Jaimyun Jung
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jaimyun Jung has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Ho Won Lee
Korea Institute of Materials Science
6 shared publications - Se-Jong Kim
Materials Data & Analysis Research Division, Korea Institute of Materials Science, 797 Changwondaero, Changwon 51508, Gyeongnam, Republic of Korea
6 shared publications - Seong-Hoon Kang
Korea Institute of Materials Science, Changwon, Republic of Korea
6 shared publications - Young-Seok Oh
Department of Materials AI & Big-Data, Korea Institute of Materials Science, 797 Changwon-daero, Seongsan-gu, Changwon-si 51508, Korea
6 shared publications - In Yong Moon
Korea Institute of Materials Science
5 shared publications Byung-Jin Choi
Technical Support Team, Forge Master Korea, Changwon 51395, Korea
1 shared publication
Latest Publications
- Open Access
- 30 April 2024
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 31 (2) , 137-145
Data-driven Approach to Explore the Contribution of Process Parameters for Laser Powder Bed Fusion of a Ti-6Al-4V Alloy
In order to predict the process window of laser powder bed fusion (LPBF) for printing metallic components, the calculation of volumetric energy density (VED) has been widely calculated for controlling process parameters. However, because it is assumed that the process parameters contribute equally to heat input, the VED still has limitation for predicting the process window of LPBF-processed materials. In this study, an explainable machine learning (xML) approach was adopted to predict and understand the contribution of each process parameter to defect evolution in Ti alloys in the LPBF process. Various ML models were trained, and the Shapley additive explanation method was adopted to quantify the importance of each process parameter. This study can offer effective guidelines for fine-tuning process parameters to fabricate high-quality products using LPBF.
- 30 April 2024
- Published by The Korean Powder Metallurgy & Materials Institute in Journal of Powder Materials
- Vol. 31 (2) , 137-145
Open AccessData-driven Approach to Explore the Contribution of Process Parameters for Laser Powder Bed Fusion of a Ti-6Al-4V Alloy
In order to predict the process window of laser powder bed fusion (LPBF) for printing metallic components, the calculation of volumetric energy density (VED) has been widely calculated for controlling process parameters. However, because it is assumed that the process parameters contribute equally to heat input, the VED still has limitation for predicting the process window of LPBF-processed materials. In this study, an explainable machine learning (xML) approach was adopted to predict and understand the contribution of each process parameter to defect evolution in Ti alloys in the LPBF process. Various ML models were trained, and the Shapley additive explanation method was adopted to quantify the importance of each process parameter. This study can offer effective guidelines for fine-tuning process parameters to fabricate high-quality products using LPBF.
- Open Access
Suppressed Plastic Anisotropy via Sigma-Phase Precipitation in CoCrFeMnNi High-Entropy Alloys
The effect of sigma-phase precipitation on plastic anisotropy of the equiatomic CoCrFeMnNi high-entropy alloy was investigated. Annealing at 700 °C after cold-rolling leads to the formation of the Cr-rich σ phase with a fraction of 2.7%. It is experimentally found that the planar anisotropy (∆r = −0.16) of the CoCrFeMnNi alloy annealed at 700 °C is two times lower than that of the alloy annealed at 800 °C (∆r = −0.35). This observation was further supported by measuring the earing profile of cup specimens after the deep drawing process. The plastic strain ratio, normal anisotropy, and planar anisotropy were also predicted using the visco-plastic self-consistent model. The results indirectly indicated that the reduction of plastic anisotropy in alloy annealed at 700 °C can be attributed to the formation of the σ phase.
Open AccessSuppressed Plastic Anisotropy via Sigma-Phase Precipitation in CoCrFeMnNi High-Entropy Alloys
The effect of sigma-phase precipitation on plastic anisotropy of the equiatomic CoCrFeMnNi high-entropy alloy was investigated. Annealing at 700 °C after cold-rolling leads to the formation of the Cr-rich σ phase with a fraction of 2.7%. It is experimentally found that the planar anisotropy (∆r = −0.16) of the CoCrFeMnNi alloy annealed at 700 °C is two times lower than that of the alloy annealed at 800 °C (∆r = −0.35). This observation was further supported by measuring the earing profile of cup specimens after the deep drawing process. The plastic strain ratio, normal anisotropy, and planar anisotropy were also predicted using the visco-plastic self-consistent model. The results indirectly indicated that the reduction of plastic anisotropy in alloy annealed at 700 °C can be attributed to the formation of the σ phase.
- 8 March 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (11) , 4780-4794
Influence of tensile properties on hole expansion ratio investigated using a generative adversarial imputation network with explainable artificial intelligence
- 8 March 2023
- Published by Springer Nature in Journal of Materials Science
- Vol. 58 (11) , 4780-4794
Influence of tensile properties on hole expansion ratio investigated using a generative adversarial imputation network with explainable artificial intelligence
- Open Access
Predicting High Temperature Flow Stress of Nickel Alloy A230 Based on an Artificial Neural Network
The high-temperature deformation behavior of metals and alloys undergoes complex mechanisms depending on the deformation conditions. The microstructure and mechanical properties after deformation are important factors that determine the strength and durability of the final product. Therefore, many studies to predict the microstructure and mechanical properties have been conducted. In this regard, numerous mathematical approaches for predicting microstructure and flow stress have been proposed over the past half century. Accordingly, many advances have been made in the field of material science. Nevertheless, there are limitations in the mathematical modeling method as there is a complex relationship between the deformation conditions and the mechanical properties. Therefore, in this study, flow stress prediction was performed by applying conventional constitutive equation and artificial intelligence technology, which is known to be effective in modeling complex relationships. As a result, it was confirmed that the flow stresses modeled by the artificial neural network showed a higher accuracy than the flow stresses modeled by the conventional Arrhenius hyperbolic sine equation.
Open AccessPredicting High Temperature Flow Stress of Nickel Alloy A230 Based on an Artificial Neural Network
The high-temperature deformation behavior of metals and alloys undergoes complex mechanisms depending on the deformation conditions. The microstructure and mechanical properties after deformation are important factors that determine the strength and durability of the final product. Therefore, many studies to predict the microstructure and mechanical properties have been conducted. In this regard, numerous mathematical approaches for predicting microstructure and flow stress have been proposed over the past half century. Accordingly, many advances have been made in the field of material science. Nevertheless, there are limitations in the mathematical modeling method as there is a complex relationship between the deformation conditions and the mechanical properties. Therefore, in this study, flow stress prediction was performed by applying conventional constitutive equation and artificial intelligence technology, which is known to be effective in modeling complex relationships. As a result, it was confirmed that the flow stresses modeled by the artificial neural network showed a higher accuracy than the flow stresses modeled by the conventional Arrhenius hyperbolic sine equation.
- Open Access
Evolution of Microstructure, Mechanical Properties and Residual Stress of a Cold Rolled Invar Sheet Due to Heat Treatment
Invar alloy possesses a uniquely low coefficient of thermal expansion, making it an ideal material for fine metal masks. To manufacture fine metal masks, Invar alloys are often cold-rolled, during which residual stress develops. Heat treatment is an effective means to control residual stress that develops within Invar sheets after cold rolling, but the treatment should be carried out with care. In this article, a comprehensive study on the effect of heat treatment on the residual stress, microstructure, and mechanical properties of a cold-rolled Invar sheet is reported. We show that while both recovery and recrystallization are effective means of reducing residual stress, substantial microstructural changes and, therefore, notable changes in mechanical properties and residual stress, occur after recrystallization. Moreover, residual stress release due to recrystallization can be affected by microstructure and texture prior to heat treatment as these factors play a significant role in recrystallization.
Open AccessEvolution of Microstructure, Mechanical Properties and Residual Stress of a Cold Rolled Invar Sheet Due to Heat Treatment
Invar alloy possesses a uniquely low coefficient of thermal expansion, making it an ideal material for fine metal masks. To manufacture fine metal masks, Invar alloys are often cold-rolled, during which residual stress develops. Heat treatment is an effective means to control residual stress that develops within Invar sheets after cold rolling, but the treatment should be carried out with care. In this article, a comprehensive study on the effect of heat treatment on the residual stress, microstructure, and mechanical properties of a cold-rolled Invar sheet is reported. We show that while both recovery and recrystallization are effective means of reducing residual stress, substantial microstructural changes and, therefore, notable changes in mechanical properties and residual stress, occur after recrystallization. Moreover, residual stress release due to recrystallization can be affected by microstructure and texture prior to heat treatment as these factors play a significant role in recrystallization.
- Open Access
Die Design for Extrusion Process of Titanium Seamless Tube Using Finite Element Analysis
In this paper, the extrusion process of titanium seamless tubes was studied using several finite element (FE) analyses. First, the finite element result was compared with experimental extrusion data acquired to validate the current analysis. Then, the effect of design parameters of the die shape was numerically analyzed using commercial FE software, Forge NxT, for the metal forming process. Elastic FE analyses were also conducted for dies to analyze the maximum principal stress that affects the early fracture of dies during the extrusion process and the maximum von Mises stress that causes the severe deformation of dies. Consequently, the effect of the corner radius at the exit and land length on the extrusion load and die stress is negligible compared to that of the corner radius at the entrance and die angle. Finally, we suggested a die angle of 60° and a corner radius at the die entrance between 10 and 15 mm as an optimal design for the current extrusion process.
Open AccessDie Design for Extrusion Process of Titanium Seamless Tube Using Finite Element Analysis
In this paper, the extrusion process of titanium seamless tubes was studied using several finite element (FE) analyses. First, the finite element result was compared with experimental extrusion data acquired to validate the current analysis. Then, the effect of design parameters of the die shape was numerically analyzed using commercial FE software, Forge NxT, for the metal forming process. Elastic FE analyses were also conducted for dies to analyze the maximum principal stress that affects the early fracture of dies during the extrusion process and the maximum von Mises stress that causes the severe deformation of dies. Consequently, the effect of the corner radius at the exit and land length on the extrusion load and die stress is negligible compared to that of the corner radius at the entrance and die angle. Finally, we suggested a die angle of 60° and a corner radius at the die entrance between 10 and 15 mm as an optimal design for the current extrusion process.
- Open Access
Design of a Forming Process for Increasing the Contact Length of Corrugated Plates in Molten Carbonate Fuel Cells
In molten carbonate fuel cell (MCFC) systems, it is known that the shape of corrugated plates has a significant influence on performance, durability, and cost. A corrugated plate with a repeating open trapezoidal-shaped slot supports membrane electrode assembly and provides a gas flow channel. To increase the efficiency of the MCFC, the slot between the corrugated and center plates has a relatively large contact length. However, increasing the contact length of the slot increases the risk of necking or fracture generation at the corner of the slot. Therefore, we focus on the development of forming technology of corrugated plate which has large contact length of slots without any necking or fracture. To this end, numerical simulation was conducted to determine the appropriate process and tool design. In the simulation, to capture shear fracture during the forming process of slots, the normalized Cockroft–Latham ductile fracture model was used. The critical value for slitting and fracture was evaluated by comparing the deformed shapes in the slitting plane obtained from experimental and simulation results. Based on simulation results, a reasonable design concept of the two-stage forming process was suggested to increase the contact length of the slot without necking or fracture. In addition, the experiment results confirmed the validity of the proposed forming process and tool design.
Open AccessDesign of a Forming Process for Increasing the Contact Length of Corrugated Plates in Molten Carbonate Fuel Cells
In molten carbonate fuel cell (MCFC) systems, it is known that the shape of corrugated plates has a significant influence on performance, durability, and cost. A corrugated plate with a repeating open trapezoidal-shaped slot supports membrane electrode assembly and provides a gas flow channel. To increase the efficiency of the MCFC, the slot between the corrugated and center plates has a relatively large contact length. However, increasing the contact length of the slot increases the risk of necking or fracture generation at the corner of the slot. Therefore, we focus on the development of forming technology of corrugated plate which has large contact length of slots without any necking or fracture. To this end, numerical simulation was conducted to determine the appropriate process and tool design. In the simulation, to capture shear fracture during the forming process of slots, the normalized Cockroft–Latham ductile fracture model was used. The critical value for slitting and fracture was evaluated by comparing the deformed shapes in the slitting plane obtained from experimental and simulation results. Based on simulation results, a reasonable design concept of the two-stage forming process was suggested to increase the contact length of the slot without necking or fracture. In addition, the experiment results confirmed the validity of the proposed forming process and tool design.
- Open Access
Investigation of the Correlation between Initial Microstructure and Critical Current Density of Nb-46.5 wt%Ti Superconducting Material
We have investigated the effect of initial microstructures on the change in critical current density (Jc) of Nb-46.5 wt%Ti (NbTi) superconducting material. It is well known that α-Ti phases distributed in NbTi material act as a flux pinning center, resulting in an improvement in critical current density. Therefore, it is crucial to obtain the grain-refined microstructure, which is strongly related with precipitation of uniformly distributed fine α-Ti phases and higher volume faction of α-Ti phases, as α-Ti phases are precipitated at the grain boundaries and triple points during heat treatments. Therefore, in order to characterize the effect of initial microstructure of NbTi on critical current density, different initial microstructures were obtained by applying equal channel angular pressing (ECAP) and hot rolling with different strains. It was revealed experimentally that hot rolling with a higher strain is efficient for obtaining the initial microstructure, which has equiaxed fine grains of β-NbTi with the aid of dynamic recrystallization, and which is helpful for precipitating fine α-Ti phases during intermediate heat treatment. Furthermore, it was confirmed that critical current density can be enhanced by obtaining a smaller α-Ti phase, a higher aspect ratio of α-Ti phase, a higher volume fraction of α-Ti phase and a ribbon-like folded α-Ti phase.
Open AccessInvestigation of the Correlation between Initial Microstructure and Critical Current Density of Nb-46.5 wt%Ti Superconducting Material
We have investigated the effect of initial microstructures on the change in critical current density (Jc) of Nb-46.5 wt%Ti (NbTi) superconducting material. It is well known that α-Ti phases distributed in NbTi material act as a flux pinning center, resulting in an improvement in critical current density. Therefore, it is crucial to obtain the grain-refined microstructure, which is strongly related with precipitation of uniformly distributed fine α-Ti phases and higher volume faction of α-Ti phases, as α-Ti phases are precipitated at the grain boundaries and triple points during heat treatments. Therefore, in order to characterize the effect of initial microstructure of NbTi on critical current density, different initial microstructures were obtained by applying equal channel angular pressing (ECAP) and hot rolling with different strains. It was revealed experimentally that hot rolling with a higher strain is efficient for obtaining the initial microstructure, which has equiaxed fine grains of β-NbTi with the aid of dynamic recrystallization, and which is helpful for precipitating fine α-Ti phases during intermediate heat treatment. Furthermore, it was confirmed that critical current density can be enhanced by obtaining a smaller α-Ti phase, a higher aspect ratio of α-Ti phase, a higher volume fraction of α-Ti phase and a ribbon-like folded α-Ti phase.
- Open Access
Analysis of the Region of Interest According to CNN Structure in Hierarchical Pattern Surface Inspection Using CAM
A convolutional neural network (CNN), which exhibits excellent performance in solving image-based problem, has been widely applied to various industrial problems. In general, the CNN model was applied to defect inspection on the surface of raw materials or final products, and its accuracy also showed better performance compared to human inspection. However, surfaces with heterogeneous and complex backgrounds have difficulties in separating defects region from the background, which is a typical challenge in this field. In this study, the CNN model was applied to detect surface defects on a hierarchical patterned surface, one of the representative complex background surfaces. In order to optimize the CNN structure, the change in inspection performance was analyzed according to the number of layers and kernel size of the model using evaluation metrics. In addition, the change of the CNN’s decision criteria according to the change of the model structure was analyzed using a class activation map (CAM) technique, which can highlight the most important region recognized by the CNN in performing classification. As a result, we were able to accurately understand the classification manner of the CNN for the hierarchical pattern surface, and an accuracy of 93.7% was achieved using the optimized model.
Open AccessAnalysis of the Region of Interest According to CNN Structure in Hierarchical Pattern Surface Inspection Using CAM
A convolutional neural network (CNN), which exhibits excellent performance in solving image-based problem, has been widely applied to various industrial problems. In general, the CNN model was applied to defect inspection on the surface of raw materials or final products, and its accuracy also showed better performance compared to human inspection. However, surfaces with heterogeneous and complex backgrounds have difficulties in separating defects region from the background, which is a typical challenge in this field. In this study, the CNN model was applied to detect surface defects on a hierarchical patterned surface, one of the representative complex background surfaces. In order to optimize the CNN structure, the change in inspection performance was analyzed according to the number of layers and kernel size of the model using evaluation metrics. In addition, the change of the CNN’s decision criteria according to the change of the model structure was analyzed using a class activation map (CAM) technique, which can highlight the most important region recognized by the CNN in performing classification. As a result, we were able to accurately understand the classification manner of the CNN for the hierarchical pattern surface, and an accuracy of 93.7% was achieved using the optimized model.