Nannan Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nannan Liu has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Fengxiao Zhai
5 shared publications- Kun Yang
Zhongyuan University of Technology
5 shared publications - Yunqi Hao
School of Electronics and Information, Zhengzhou University of Light Industry, Zhengzhou 450001, China
5 shared publications Wenyan Zhang
4 shared publicationsFutian Li
3 shared publicationsJiahao Tian
3 shared publications
Latest Publications
- 27 October 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (31) , 11028
Dual-tapered graded-index two-mode fiber and peak-detection improvement algorithm for refractive index sensing
Dual tapers based on a graded-index (GI) two-mode (TM) fiber are proposed for refractive index (RI) sensing in this work. Sensitivity of 1433.94 nm/RIU with R 2 =0.98 is achieved using the direct peak-finding method, where the sensitivity enhancement originated from two guided modes and corresponding two sets of excited cladding modes. To improve wavelength demodulation accuracy, spatial frequency concentration algorithm is presented to filter out the influence of optical intensity fluctuations and mode noise via a bandpass filter, and yielding the sensing sensitivity 1669.61 nm/RIU and R 2 =0.9699 after data processing. Furthermore, empirical mode decomposition (EMD) is utilized to decompose transmission spectra according to their noise features. By calculating correlation coefficients between each intrinsic mode function and the raw spectrum, noise components are eliminated to smooth the spectra. The EMD-processed spectra produce the sensing sensitivity of 1458.52 nm/RIU with R 2 =0.9930 through peak-finding again. Experimental results demonstrate that the GI two-mode fiber enhances the sensing sensitivity of tapered fiber sensors, while the EMD algorithm improves the sensing accuracy. The results in this work could provide technical support for the practical sensing applications of tapered fiber sensors.
- 27 October 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (31) , 11028
Dual-tapered graded-index two-mode fiber and peak-detection improvement algorithm for refractive index sensing
Dual tapers based on a graded-index (GI) two-mode (TM) fiber are proposed for refractive index (RI) sensing in this work. Sensitivity of 1433.94 nm/RIU with R 2 =0.98 is achieved using the direct peak-finding method, where the sensitivity enhancement originated from two guided modes and corresponding two sets of excited cladding modes. To improve wavelength demodulation accuracy, spatial frequency concentration algorithm is presented to filter out the influence of optical intensity fluctuations and mode noise via a bandpass filter, and yielding the sensing sensitivity 1669.61 nm/RIU and R 2 =0.9699 after data processing. Furthermore, empirical mode decomposition (EMD) is utilized to decompose transmission spectra according to their noise features. By calculating correlation coefficients between each intrinsic mode function and the raw spectrum, noise components are eliminated to smooth the spectra. The EMD-processed spectra produce the sensing sensitivity of 1458.52 nm/RIU with R 2 =0.9930 through peak-finding again. Experimental results demonstrate that the GI two-mode fiber enhances the sensing sensitivity of tapered fiber sensors, while the EMD algorithm improves the sensing accuracy. The results in this work could provide technical support for the practical sensing applications of tapered fiber sensors.
- Open Access
- 14 October 2026
- Published by Elsevier in SSRN Electronic Journal
Optical Phase Measurement Enhanced by a Degenerate Fiber Optical Parametric Amplifier
Optical phase measurement is widely used in precision metrology and sensing, but the detection of weak phase variations can be strongly affected by detector noise and other technical noise sources, particularly at low optical powers. In this work, we demonstrate an optical phase-measurement approach based on a single-stage degenerate fiber optical parametric amplifier (DFOPA). The phase-sensitive response of the DFOPA converts the phase modulation carried by the input optical field into an amplified intensity variation, enabling direct photodetection without requiring an external local oscillator or balanced homodyne detection setup. The DFOPA exhibits a maximum phase-sensitive power gain of 24.9 dB, a minimum gain of −4.9 dB, and near-unity phase-sensitive fringe visibility. Its phase-measurement performance is quantitatively compared with that of a conventional Mach–Zehnder interferometer (MZI). At a carrier power of 1 μW, the DFOPA-based measurement achieves an SNR of 15.21±0.90 dB, compared with 6.03±0.80 dB for the MZI, corresponding to an enhancement of 9.18 dB. The effects of the operating point, carrier power, and pump power on the phase-measurement performance are further characterized. The SNR advantage becomes more pronounced at low carrier powers and increases with pump power. These results demonstrate that a DFOPA can provide an effective all-fiber approach for direct optical phase readout and SNR enhancement under low-optical-power conditions.
- 14 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptical Phase Measurement Enhanced by a Degenerate Fiber Optical Parametric Amplifier
Optical phase measurement is widely used in precision metrology and sensing, but the detection of weak phase variations can be strongly affected by detector noise and other technical noise sources, particularly at low optical powers. In this work, we demonstrate an optical phase-measurement approach based on a single-stage degenerate fiber optical parametric amplifier (DFOPA). The phase-sensitive response of the DFOPA converts the phase modulation carried by the input optical field into an amplified intensity variation, enabling direct photodetection without requiring an external local oscillator or balanced homodyne detection setup. The DFOPA exhibits a maximum phase-sensitive power gain of 24.9 dB, a minimum gain of −4.9 dB, and near-unity phase-sensitive fringe visibility. Its phase-measurement performance is quantitatively compared with that of a conventional Mach–Zehnder interferometer (MZI). At a carrier power of 1 μW, the DFOPA-based measurement achieves an SNR of 15.21±0.90 dB, compared with 6.03±0.80 dB for the MZI, corresponding to an enhancement of 9.18 dB. The effects of the operating point, carrier power, and pump power on the phase-measurement performance are further characterized. The SNR advantage becomes more pronounced at low carrier powers and increases with pump power. These results demonstrate that a DFOPA can provide an effective all-fiber approach for direct optical phase readout and SNR enhancement under low-optical-power conditions.
- Open Access
- 21 March 2026
- Published by Elsevier in SSRN Electronic Journal
All-fiber switchable bidirectional soliton laser: design and performance
We demonstrate a fully fiber-integrated bidirectional pulsed laser by employing thulium-doped fiber (TDF) as a saturable absorber for self-starting operation. Through precise manipulating the intracavity polarization, loss, and pump power, stable bidirectional output of diverse mode-locked pulses in both clockwise (CW) and counterclockwise (CCW) directions can be achieved and switched, which include bright solitons, bright-dark soliton pairs, and high-order harmonic mode-locking, with harmonic orders up to 6th (CW) and 5th (CCW), respectively. Notably, this work reports the first bidirectional generation of bright-dark soliton pairs. Attributed to the asymmetric design of the cavity structure, the fundamental bright solitons in bidirectional outputs exhibit a repetition frequency difference of approximately 0.56 MHz, enabling direct deployment as a single-cavity dual-comb source. Moreover, this fully fiber-structure laser with high stability and good tunability, can be compatible with a variety of fiber-optic systems. The unique properties of bidirectional operation with repetition rate disparity, provide a viable solution for optical frequency comb generation and precision spectral measurements.
- 21 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAll-fiber switchable bidirectional soliton laser: design and performance
We demonstrate a fully fiber-integrated bidirectional pulsed laser by employing thulium-doped fiber (TDF) as a saturable absorber for self-starting operation. Through precise manipulating the intracavity polarization, loss, and pump power, stable bidirectional output of diverse mode-locked pulses in both clockwise (CW) and counterclockwise (CCW) directions can be achieved and switched, which include bright solitons, bright-dark soliton pairs, and high-order harmonic mode-locking, with harmonic orders up to 6th (CW) and 5th (CCW), respectively. Notably, this work reports the first bidirectional generation of bright-dark soliton pairs. Attributed to the asymmetric design of the cavity structure, the fundamental bright solitons in bidirectional outputs exhibit a repetition frequency difference of approximately 0.56 MHz, enabling direct deployment as a single-cavity dual-comb source. Moreover, this fully fiber-structure laser with high stability and good tunability, can be compatible with a variety of fiber-optic systems. The unique properties of bidirectional operation with repetition rate disparity, provide a viable solution for optical frequency comb generation and precision spectral measurements.
- Open Access
- 17 March 2026
- Published by Elsevier in SSRN Electronic Journal
Sensitivity Enhancement of Dual-Tapered Fiber Refractive Index Sensor Assisted by Tilted Fiber Bragg Grating
Without further pulling the fiber diameter to only several micrometer and to keep the mechanical strength of fiber tapers, the sensitivity enhancement scheme of refractive index (RI) sensing based on dual-tapered fiber is proposed in this paper. A tilted fiber Bragg grating (TFBG) is cascaded to the fiber tapers; and the superimposed envelope spectrum is extracted via Hilbert transform. Within RI range 1.3325-1.3382, experimental results show that sensitivity of the TFBG assisted dual-tapers structure has been improved to 84.245 nm/RIU from 37.511 nm/RIU for the same 20.11 µm waist diameter. Comparatively, the RI sensitivity is boosted only 12.12% to 42.131 nm/RIU with the spatial frequency concentrated algorithm in the data processing for the single dual-taper. The sensitivity amplification factor is 2.25 for the TFBG assisted dual-tapers sensor, providing a low-cost and effective solution for trace detection in biological sensing and environmental monitoring, etc.
- 17 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSensitivity Enhancement of Dual-Tapered Fiber Refractive Index Sensor Assisted by Tilted Fiber Bragg Grating
Without further pulling the fiber diameter to only several micrometer and to keep the mechanical strength of fiber tapers, the sensitivity enhancement scheme of refractive index (RI) sensing based on dual-tapered fiber is proposed in this paper. A tilted fiber Bragg grating (TFBG) is cascaded to the fiber tapers; and the superimposed envelope spectrum is extracted via Hilbert transform. Within RI range 1.3325-1.3382, experimental results show that sensitivity of the TFBG assisted dual-tapers structure has been improved to 84.245 nm/RIU from 37.511 nm/RIU for the same 20.11 µm waist diameter. Comparatively, the RI sensitivity is boosted only 12.12% to 42.131 nm/RIU with the spatial frequency concentrated algorithm in the data processing for the single dual-taper. The sensitivity amplification factor is 2.25 for the TFBG assisted dual-tapers sensor, providing a low-cost and effective solution for trace detection in biological sensing and environmental monitoring, etc.
- Open Access
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Dual-tapered graded-index two-mode fiber and peak-detection improvement algorithm for refractive index sensing
Dual-tapers based on graded index (GI) two-mode (TM) fiber are proposed for refractive index (RI) sensing, and the spatial frequency concentration algorithm for wavelength demodulation accuracy is presented to improve the sensing sensitivity. The transmission spectrum is comb-like with extinction ratio (ER) 24.74dB and free spectrum range (FSR) 11.76nm. With direct peak-finding method, its sensitivity is 2033.33 nm/RIU, which is about twice as single-mode dual-tapers. To eliminate influence of optical intensity fluctuation and mode noise, spatial frequency concentrated algorithm is applied on the RI sensing spectra; sensitivity 2333.33nm/RIU is obtained, about 14% improvement to direct peak-finding. Three peak-detection algorithms including quadratic polynomial fitting, Gaussian fitting, Gaussian-polynomial fitting are subsequently compared to locate the peak-wavelength accurately, corresponding to sensitivities 16477.45nm/RIU, 13823.38nm/RIU, 12787.45nm/RIU and standard deviations 0.8160, 0.8281, 0.8342. Comparison results show that GI TM tapers together with frequency concentration algorithm and quadratic polynomial fitting method has the highest 8.1 times sensitivity enhancement. This GI TM tapers and peak-wavelength detection algorithm have potential for trace detection in chemical and biomedical sensing fields.
- 13 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDual-tapered graded-index two-mode fiber and peak-detection improvement algorithm for refractive index sensing
Dual-tapers based on graded index (GI) two-mode (TM) fiber are proposed for refractive index (RI) sensing, and the spatial frequency concentration algorithm for wavelength demodulation accuracy is presented to improve the sensing sensitivity. The transmission spectrum is comb-like with extinction ratio (ER) 24.74dB and free spectrum range (FSR) 11.76nm. With direct peak-finding method, its sensitivity is 2033.33 nm/RIU, which is about twice as single-mode dual-tapers. To eliminate influence of optical intensity fluctuation and mode noise, spatial frequency concentrated algorithm is applied on the RI sensing spectra; sensitivity 2333.33nm/RIU is obtained, about 14% improvement to direct peak-finding. Three peak-detection algorithms including quadratic polynomial fitting, Gaussian fitting, Gaussian-polynomial fitting are subsequently compared to locate the peak-wavelength accurately, corresponding to sensitivities 16477.45nm/RIU, 13823.38nm/RIU, 12787.45nm/RIU and standard deviations 0.8160, 0.8281, 0.8342. Comparison results show that GI TM tapers together with frequency concentration algorithm and quadratic polynomial fitting method has the highest 8.1 times sensitivity enhancement. This GI TM tapers and peak-wavelength detection algorithm have potential for trace detection in chemical and biomedical sensing fields.
- Open Access
Multiple Dissipative Solitons in an Erbium-Doped Fiber Laser Mode-Locked with Ethylene Glycol
We report the experimental observation of dissipative solitons (DS) in an erbium-doped fiber laser mode-locked with ethylene glycol. Stable individual dissipative solitons with the fundamental repetition frequency of 35.17 MHz are obtained. The spectral profiles exhibit dynamic variation, adopting either a parabolic-like or an M-like shape at varying pump levels. Moreover, through increasing the pump power and/or appropriately regulating the polarization controller, multiple dissipative solitons, including soliton pairs and soliton triplet states have also been achieved. The generation mechanism is attributed to the phenomenon of peak clamping effect. This is the first demonstration of a dissipative soliton laser utilizing ethylene glycol as a saturable absorber. It is anticipated that this demonstration will spur further attention on organic liquid SAs and potentially extend significant influence for the application of ultrafast lasers.
Open AccessMultiple Dissipative Solitons in an Erbium-Doped Fiber Laser Mode-Locked with Ethylene Glycol
We report the experimental observation of dissipative solitons (DS) in an erbium-doped fiber laser mode-locked with ethylene glycol. Stable individual dissipative solitons with the fundamental repetition frequency of 35.17 MHz are obtained. The spectral profiles exhibit dynamic variation, adopting either a parabolic-like or an M-like shape at varying pump levels. Moreover, through increasing the pump power and/or appropriately regulating the polarization controller, multiple dissipative solitons, including soliton pairs and soliton triplet states have also been achieved. The generation mechanism is attributed to the phenomenon of peak clamping effect. This is the first demonstration of a dissipative soliton laser utilizing ethylene glycol as a saturable absorber. It is anticipated that this demonstration will spur further attention on organic liquid SAs and potentially extend significant influence for the application of ultrafast lasers.
- Open Access
- 22 August 2025
- Published by MDPI AG in Preprints.org
Multiple Dissipative Solitons in an Erbium-Doped Fiber Laser Mode-Locked with Ethylene Glycol
We report the experimental observation of dissipative solitons (DS) in an erbium-doped fiber laser mode locked with ethylene glycol. Stable individual dissipative solitons with nanosecond pulse duration are obtained. The spectral profiles exhibit dynamic variation, adopting either a parabolic-like or an M-like shape at varying pump levels. Moreover, through increasing the pump power and/or appropriately regulating the polarization controller, multiple dissipative solitons, including soliton pairs and soliton triplet states have also been achieved. The generation mechanism is attributed to the phenomenon of peak clamping effect. This is the first demonstration of a dissipative soliton laser utilizing ethylene glycol as a saturable absorber. It is anticipated that this demonstration will spur further attention on organic liquid SAs and potentially extend significant influence for the application of ultrafast lasers.
- 22 August 2025
- Published by MDPI AG in Preprints.org
Open AccessMultiple Dissipative Solitons in an Erbium-Doped Fiber Laser Mode-Locked with Ethylene Glycol
We report the experimental observation of dissipative solitons (DS) in an erbium-doped fiber laser mode locked with ethylene glycol. Stable individual dissipative solitons with nanosecond pulse duration are obtained. The spectral profiles exhibit dynamic variation, adopting either a parabolic-like or an M-like shape at varying pump levels. Moreover, through increasing the pump power and/or appropriately regulating the polarization controller, multiple dissipative solitons, including soliton pairs and soliton triplet states have also been achieved. The generation mechanism is attributed to the phenomenon of peak clamping effect. This is the first demonstration of a dissipative soliton laser utilizing ethylene glycol as a saturable absorber. It is anticipated that this demonstration will spur further attention on organic liquid SAs and potentially extend significant influence for the application of ultrafast lasers.
- Open Access
- 24 April 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (5) , 055203
Dispersion measurement of optical fibers based on a phase-locked unbalanced Mach–Zehnder interferometer
Accurate measurement of optical fiber dispersion is important for optical processing, such as optical communication, optical fiber-based quantum state generation, etc. In this paper, we propose a new method for measuring optical fiber dispersion that can accurately measure the dispersion of long optical fibers in a wide spectral range. By using a femtosecond laser and unbalanced Mach–Zehnder interferometer with a phase-locking system, the coherence length of the optical source and stability of dispersion measurement have been improved. Thus, we overcome the shortcomings of traditional dispersion measurement methods that are difficult to make compatible with long fibers and wide spectral ranges. Using this method, we measure the dispersion parameters of two pieces of dispersion shifted fiber (DSF) with lengths of 200 m and 300 m, respectively, in the wavelength range 1500–1600 nm. Measurement results show that the zero-dispersion wavelength (ZDW) and the zero-dispersion slope (ZDS) of the 200 m DSF are 1535.53 ± 0.05 nm and 0.034 ± 10−4 ps nm–2 km−1, respectively, while the ZDW and ZDS of the 300 m DSF are 1551.26 ± 0.06 nm and 0.040 ± 10−5 ps nm–2 km−1, respectively. We test the stability of the system by using the root-mean-square (RMS) fluctuations of six measurements of the dispersion parameter D(λ) for the two pieces of fiber; the RMS values are both less than 0.02 ps nm–1 km−1. Our research is valuable for measurement of dispersion for long fibers within a wide spectral range, considering the effects of fiber uniformity.
- 24 April 2025
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 36 (5) , 055203
Open AccessDispersion measurement of optical fibers based on a phase-locked unbalanced Mach–Zehnder interferometer
Accurate measurement of optical fiber dispersion is important for optical processing, such as optical communication, optical fiber-based quantum state generation, etc. In this paper, we propose a new method for measuring optical fiber dispersion that can accurately measure the dispersion of long optical fibers in a wide spectral range. By using a femtosecond laser and unbalanced Mach–Zehnder interferometer with a phase-locking system, the coherence length of the optical source and stability of dispersion measurement have been improved. Thus, we overcome the shortcomings of traditional dispersion measurement methods that are difficult to make compatible with long fibers and wide spectral ranges. Using this method, we measure the dispersion parameters of two pieces of dispersion shifted fiber (DSF) with lengths of 200 m and 300 m, respectively, in the wavelength range 1500–1600 nm. Measurement results show that the zero-dispersion wavelength (ZDW) and the zero-dispersion slope (ZDS) of the 200 m DSF are 1535.53 ± 0.05 nm and 0.034 ± 10−4 ps nm–2 km−1, respectively, while the ZDW and ZDS of the 300 m DSF are 1551.26 ± 0.06 nm and 0.040 ± 10−5 ps nm–2 km−1, respectively. We test the stability of the system by using the root-mean-square (RMS) fluctuations of six measurements of the dispersion parameter D(λ) for the two pieces of fiber; the RMS values are both less than 0.02 ps nm–1 km−1. Our research is valuable for measurement of dispersion for long fibers within a wide spectral range, considering the effects of fiber uniformity.
- 8 February 2025
- Published by Elsevier in Optical Fiber Technology
- Vol. 91
Generation of two-channel intensity difference squeezing by using a single fiber-optical parametric amplifier
- 8 February 2025
- Published by Elsevier in Optical Fiber Technology
- Vol. 91
Generation of two-channel intensity difference squeezing by using a single fiber-optical parametric amplifier
- 25 November 2024
- Published by American Physical Society (APS) in Physical Review A
- Vol. 110 (5)
Scalable quantum optical tap for the distribution of quantum information encoded in entangled fields
- 25 November 2024
- Published by American Physical Society (APS) in Physical Review A
- Vol. 110 (5)
Scalable quantum optical tap for the distribution of quantum information encoded in entangled fields