Syed Riyaz Ahammed
Syed Riyaz Ahammed has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Ayyappan Susila Praveen
Department of Mechanical Engineering, Vel Tech Rangarajan Dr. Sagunthala R&D Institute of Science and Technology, Avadi, Chennai, Tamil Nadu, India
2 shared publications- A. Arul Edwin Raj
Faculty of Electrical and Electronic Engineering Universiti tun Hussein Onn Malaysia Batu Pahat Johor Malaysia
1 shared publication - Akhlaqur Rahman
Engineering Institute of Technology, Melbourne Campus, Melbourne, VIC 3000, Australia
1 shared publication - Albert T1 shared publication
- Ashok Vajravelu
Universiti Tun Hussein Onn Malaysia
1 shared publication - Asmarashid Ponniran
Faculty of Electrical and Electronic Engineering, Universiti Tun Hussein Onn Malaysia, Parit Raja, Johor, Malaysia
1 shared publication
Latest Publications
- 18 September 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (28) , 58677-58680
Direct ink writing of β-TCP bioceramic scaffolds: rheology-guided processing and structural control toward bone tissue engineering
- 18 September 2026
- Published by Elsevier in Ceramics International
- Vol. 52 (28) , 58677-58680
Direct ink writing of β-TCP bioceramic scaffolds: rheology-guided processing and structural control toward bone tissue engineering
- Open Access
- 14 September 2026
- Published by International Journal of Renewable Energy Research in Artificial Intelligence Research and Applications
- Vol. 2 (3) , 167-173
An Explainable Artificial Intelligence Model for Energy Flow Management in EV-Dominated Microgrids
Microgrids are being changed rapidly as Electric Vehicles (EVs) become more popular and many new variable and unpredictable energy loads are being added, along with an abundance of new ways to store energy using electric vehicles (EVs) through vehicle-to-grid interactions. To achieve optimal energy flow control in microgrids characterized by power generation and energy storage facilities with an overwhelming percentage of power flowing from the electric vehicle (EV), intelligent decision support systems that provide suitable solutions based on accurate and credible information must be used. This paper describes a model utilizing Explainable Artificial Intelligence (XAI) for managing the flow of energy between various types of energy generation resources, stationary energy storage resources, EVs, and the grid in order to produce a minimum cost/performance and maximum reliability. Specifically, the proposed model integrates SHAP (SHapley Additive exPlanations) and rule extraction with gradient-boosted trees to balance performance improvements, cost reductions, and grid stability. Unlike conventional black-box or purely optimization-based methods like Model Predictive Control (MPC), this approach provides explicit, quantifiable feature attributions for every operational decision. Simulation results from various types of operation demonstrate that the proposed model improves the utilization of energy, reduces peak demand, and increases transparency of decision making. The inclusion of the explainable AI aspect will enhance the level of confidence operators will place on the model and improve regulatory compliance, and therefore, this approach is a good candidate for use in future smart microgrid deployments.
- 14 September 2026
- Published by International Journal of Renewable Energy Research in Artificial Intelligence Research and Applications
- Vol. 2 (3) , 167-173
Open AccessAn Explainable Artificial Intelligence Model for Energy Flow Management in EV-Dominated Microgrids
Microgrids are being changed rapidly as Electric Vehicles (EVs) become more popular and many new variable and unpredictable energy loads are being added, along with an abundance of new ways to store energy using electric vehicles (EVs) through vehicle-to-grid interactions. To achieve optimal energy flow control in microgrids characterized by power generation and energy storage facilities with an overwhelming percentage of power flowing from the electric vehicle (EV), intelligent decision support systems that provide suitable solutions based on accurate and credible information must be used. This paper describes a model utilizing Explainable Artificial Intelligence (XAI) for managing the flow of energy between various types of energy generation resources, stationary energy storage resources, EVs, and the grid in order to produce a minimum cost/performance and maximum reliability. Specifically, the proposed model integrates SHAP (SHapley Additive exPlanations) and rule extraction with gradient-boosted trees to balance performance improvements, cost reductions, and grid stability. Unlike conventional black-box or purely optimization-based methods like Model Predictive Control (MPC), this approach provides explicit, quantifiable feature attributions for every operational decision. Simulation results from various types of operation demonstrate that the proposed model improves the utilization of energy, reduces peak demand, and increases transparency of decision making. The inclusion of the explainable AI aspect will enhance the level of confidence operators will place on the model and improve regulatory compliance, and therefore, this approach is a good candidate for use in future smart microgrid deployments.
- 4 June 2026
- Published by International Journal of Renewable Energy Research in Artificial Intelligence Research and Applications
- Vol. 2 (2) , 124-130
Autonomous Scheduling of Electric Vehicle Charging in Renewable Microgrids Using Deep Reinforcement Learning
This study outlines an autonomous charging schedule for electric vehicles (EVs) within a renewable microgrid that uses deep policy learning. Renewable energy-based micro-grid energy management systems are combined with a reinforcement learning agent that balances demand for EV charging, PV production and battery storage (i.e., variable energy sources) through EV charging identified by an agent observing the state of the microgrid, renewable resource forecasts and vehicle arrival profiles in order to select charge rates that result in minimum cost, peak demand reduction and maximization of renewable resource use. Simulation experiments of realistic load and generation time histories indicate that the proposed strategy produces a better utilization of renewable energy than heuristic scheduling methods, as well as providing potential cost savings from improving renewable energy utilization. The simulation results also demonstrate that the scheduling strategy is capable of making continuous adaptions to the variability in loads, generation and constraints of the microgrid while still meeting the charging demands of users and maintaining compliance with microgrid regulations. Through its scalability, capability to accommodate multiple vehicles simultaneously and ability to adapt continuously to changes in operating conditions, this framework provides lower operating costs, reduced emissions and increased resilience for renewable energy-based micro-grids. Future research will investigate methods for coordinating multiple agents and deploying the framework in the field. Extensive ablation studies will help quantify the contribution of each component and determine the stability of the charging policy under various scenarios.
- 4 June 2026
- Published by International Journal of Renewable Energy Research in Artificial Intelligence Research and Applications
- Vol. 2 (2) , 124-130
Autonomous Scheduling of Electric Vehicle Charging in Renewable Microgrids Using Deep Reinforcement Learning
This study outlines an autonomous charging schedule for electric vehicles (EVs) within a renewable microgrid that uses deep policy learning. Renewable energy-based micro-grid energy management systems are combined with a reinforcement learning agent that balances demand for EV charging, PV production and battery storage (i.e., variable energy sources) through EV charging identified by an agent observing the state of the microgrid, renewable resource forecasts and vehicle arrival profiles in order to select charge rates that result in minimum cost, peak demand reduction and maximization of renewable resource use. Simulation experiments of realistic load and generation time histories indicate that the proposed strategy produces a better utilization of renewable energy than heuristic scheduling methods, as well as providing potential cost savings from improving renewable energy utilization. The simulation results also demonstrate that the scheduling strategy is capable of making continuous adaptions to the variability in loads, generation and constraints of the microgrid while still meeting the charging demands of users and maintaining compliance with microgrid regulations. Through its scalability, capability to accommodate multiple vehicles simultaneously and ability to adapt continuously to changes in operating conditions, this framework provides lower operating costs, reduced emissions and increased resilience for renewable energy-based micro-grids. Future research will investigate methods for coordinating multiple agents and deploying the framework in the field. Extensive ablation studies will help quantify the contribution of each component and determine the stability of the charging policy under various scenarios.
- Open Access
- 1 January 2026
- Published by Wiley in International Journal of Intelligent Systems
- Vol. 2026 (1)
Machine Learning Classifier–Based Breast Thermography Enhancement Using Adaptive Multiaverage Gamma Correction for Breast Cancer Diagnosis
Detecting breast cancer has always been a challenging task in medicinal field. Among various screening techniques, breast thermography proves to be a reliable technique. Though it aids in the diagnosis of tumors, its low color contrast between diseased and normal tissues makes it difficult to identify subtle image features and detect cancer in thick breast tissues. To solve these problems, this study presents an adaptive multiaverage gamma correction (AMAGC) technique that improves breast thermograms by increasing contrast between cancerous and normal regions. Using an enhanced greyscale image as a reference, the AMAGC method separates the grayscale thermogram into several subimages according to their different brightness levels (low, medium, and high). This is followed by applying customized average gamma corrections to each subimage, and then performing histogram matching on the Value (V) component of the HSV color model. This technique was implemented on PC running MATLAB 2016a. Comprehensive objective quality measures, such as PSNR, AMBE, SSIM, and DSSIM, were used for validation. Dimension‐reduced GLCM features were used for classification using a Random Forest (RF) classifier created in Python/Jupiter. The classification stage is used exclusively to test the diagnostic value of the improved thermograms. A total of 120 segmented thermal pictures received from the Indira Gandhi Centre for Atomic Research (IGCAR) in Kalpakkam, India, constitute the dataset. With the RF classifier achieving 95.3% accuracy, 97.2% sensitivity, and 95.7% specificity, experimental results showed that AMAGC significantly outperformed traditional methods, such as BBHE, DSIHE, and RETINEX, in both subjective and objective assessments, emphasizing the efficacy of the proposed improvement method in computer‐aided diagnosis in breast cancer cases.
- 1 January 2026
- Published by Wiley in International Journal of Intelligent Systems
- Vol. 2026 (1)
Open AccessMachine Learning Classifier–Based Breast Thermography Enhancement Using Adaptive Multiaverage Gamma Correction for Breast Cancer Diagnosis
Detecting breast cancer has always been a challenging task in medicinal field. Among various screening techniques, breast thermography proves to be a reliable technique. Though it aids in the diagnosis of tumors, its low color contrast between diseased and normal tissues makes it difficult to identify subtle image features and detect cancer in thick breast tissues. To solve these problems, this study presents an adaptive multiaverage gamma correction (AMAGC) technique that improves breast thermograms by increasing contrast between cancerous and normal regions. Using an enhanced greyscale image as a reference, the AMAGC method separates the grayscale thermogram into several subimages according to their different brightness levels (low, medium, and high). This is followed by applying customized average gamma corrections to each subimage, and then performing histogram matching on the Value (V) component of the HSV color model. This technique was implemented on PC running MATLAB 2016a. Comprehensive objective quality measures, such as PSNR, AMBE, SSIM, and DSSIM, were used for validation. Dimension‐reduced GLCM features were used for classification using a Random Forest (RF) classifier created in Python/Jupiter. The classification stage is used exclusively to test the diagnostic value of the improved thermograms. A total of 120 segmented thermal pictures received from the Indira Gandhi Centre for Atomic Research (IGCAR) in Kalpakkam, India, constitute the dataset. With the RF classifier achieving 95.3% accuracy, 97.2% sensitivity, and 95.7% specificity, experimental results showed that AMAGC significantly outperformed traditional methods, such as BBHE, DSIHE, and RETINEX, in both subjective and objective assessments, emphasizing the efficacy of the proposed improvement method in computer‐aided diagnosis in breast cancer cases.
- Open Access
- 30 April 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (9) , 3788
An Optimization Algorithm for Embedded Raspberry Pi Pico Controllers for Solar Tree Systems
Solar photovoltaic (PV) systems stand out as a promising solution for generating clean, carbon-free energy. However, traditional solar panel installations often require extensive land resources, which could become scarce as the population grows. To address this challenge, innovative approaches are needed to maximize solar power generation within limited spaces. One promising concept involves the development of biological tree-like structures housing solar panels. These “solar trees” mimic the arrangement of branches and leaves found in natural trees, following patterns akin to phyllotaxy, which correlates with the Fibonacci sequence and golden ratio. By adopting an alternative 1:3 phyllotaxy pattern, three solar panels can be efficiently arranged along the stem of the solar tree structure, each rotated at a 120-degree displacement. Optimizing the performance of solar trees requires effective maximum power point tracking (MPPT), a crucial process for extracting the maximum available power from solar panels to enhance the overall efficiency. In this study, a novel metaheuristic algorithm called horse herd optimization (HHO) is employed for MPPT in solar tree applications. Moreover, to efficiently manage the generated power, a cascaded buck–boost converter is utilized. This converter is capable of adjusting the DC voltage levels to match the system requirements within a single topology. The algorithm is implemented using MATLAB and embedded within a Raspberry Pi Pico controller, which facilitates the generation of pulse-width modulation (PWM) signals to control the cascaded buck–boost converter. Through extensive validation, this study confirms the effectiveness of the proposed HHO algorithm integrated into the Raspberry Pi Pico controller for optimizing solar trees under various shading conditions. In essence, this research highlights the potential of solar tree structures coupled with advanced MPPT algorithms and power management systems to maximize solar energy utilization, offering a sustainable solution for clean energy generation within limited land resources.
- 30 April 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (9) , 3788
Open AccessAn Optimization Algorithm for Embedded Raspberry Pi Pico Controllers for Solar Tree Systems
Solar photovoltaic (PV) systems stand out as a promising solution for generating clean, carbon-free energy. However, traditional solar panel installations often require extensive land resources, which could become scarce as the population grows. To address this challenge, innovative approaches are needed to maximize solar power generation within limited spaces. One promising concept involves the development of biological tree-like structures housing solar panels. These “solar trees” mimic the arrangement of branches and leaves found in natural trees, following patterns akin to phyllotaxy, which correlates with the Fibonacci sequence and golden ratio. By adopting an alternative 1:3 phyllotaxy pattern, three solar panels can be efficiently arranged along the stem of the solar tree structure, each rotated at a 120-degree displacement. Optimizing the performance of solar trees requires effective maximum power point tracking (MPPT), a crucial process for extracting the maximum available power from solar panels to enhance the overall efficiency. In this study, a novel metaheuristic algorithm called horse herd optimization (HHO) is employed for MPPT in solar tree applications. Moreover, to efficiently manage the generated power, a cascaded buck–boost converter is utilized. This converter is capable of adjusting the DC voltage levels to match the system requirements within a single topology. The algorithm is implemented using MATLAB and embedded within a Raspberry Pi Pico controller, which facilitates the generation of pulse-width modulation (PWM) signals to control the cascaded buck–boost converter. Through extensive validation, this study confirms the effectiveness of the proposed HHO algorithm integrated into the Raspberry Pi Pico controller for optimizing solar trees under various shading conditions. In essence, this research highlights the potential of solar tree structures coupled with advanced MPPT algorithms and power management systems to maximize solar energy utilization, offering a sustainable solution for clean energy generation within limited land resources.
- Open Access
- 8 March 2024
- Published by Carbon Magics Ltd in International Journal of Vehicle Structures & Systems
- Vol. 16 (1)
Performance Analysis of a DI Diesel Engine using Prosopis Juliflora Biodiesel in Conjunction with Hydrogen Fuel
This paper focusing on introduction of hydrogen effect on diesel engine performance and emissions. Researchers are exploring alternatives to petroleum fuels amid a rapid depletion of petroleum resources. As a low-cost raw material, waste can be exploited for economic gain. One might anticipate lower manufacturing costs by utilising lignocellulosic materials, such as Prosopis Juliflora. Prosopis Juliflora, an arid and semi-arid plant feedstock, was utilised to make biodiesel. To determine the performance and emissions characteristics of Prosopis Juliflora biodiesel (PJB), this paper combines hydrogen gas as dual fuel. The fuel's performance was tested using a single cylinder diesel engine. There was no significant difference in performance between the various fuels. Smoke emissions were reduced, NOx levels were increased, and thermal efficiency was improved.
- 8 March 2024
- Published by Carbon Magics Ltd in International Journal of Vehicle Structures & Systems
- Vol. 16 (1)
Open AccessPerformance Analysis of a DI Diesel Engine using Prosopis Juliflora Biodiesel in Conjunction with Hydrogen Fuel
This paper focusing on introduction of hydrogen effect on diesel engine performance and emissions. Researchers are exploring alternatives to petroleum fuels amid a rapid depletion of petroleum resources. As a low-cost raw material, waste can be exploited for economic gain. One might anticipate lower manufacturing costs by utilising lignocellulosic materials, such as Prosopis Juliflora. Prosopis Juliflora, an arid and semi-arid plant feedstock, was utilised to make biodiesel. To determine the performance and emissions characteristics of Prosopis Juliflora biodiesel (PJB), this paper combines hydrogen gas as dual fuel. The fuel's performance was tested using a single cylinder diesel engine. There was no significant difference in performance between the various fuels. Smoke emissions were reduced, NOx levels were increased, and thermal efficiency was improved.
- Open Access
- 22 June 2021
- Published by EDP Sciences in International Journal for Simulation and Multidisciplinary Design Optimization
- Vol. 12, 7
Optimization parameters effects on electrical conductivity of 3D printed circuits fabricated by direct ink writing method using functionalized multiwalled carbon nanotubes and polyvinyl alcohol conductive ink
Fabrication of electronic circuits and the effects of optimization parameters on electrical conductivity of the printed circuits fabricated by direct ink writing method (D.I.W); one of the novel methods in 3D printing technologies is discussed in this work. This paper focuses on fabrication of electronic circuits using F-MWCNT/PVA conductive ink and analyses the effect of input printing process parameters namely nozzle diameter, extrusion pressure, printing speed on evaluating the electrical conductivity. Box–Behnken approach is followed to generate the levels of experiments and the performance of developed model is assessed using ANOVA. Response surface method is incorporated to find the influencing parameters on electrical conductivity response. Two-point probe measurement method is performed to analyse the output response of the printed electronic circuits. Optimized printing parameters such as nozzle diameter of 0.8 mm, extrusion pressure of 0.1 MPa and printing speed of 4 mm/sec are found to be the best the for printing electronic circuits with high electrical conductivity.
- 22 June 2021
- Published by EDP Sciences in International Journal for Simulation and Multidisciplinary Design Optimization
- Vol. 12, 7
Open AccessOptimization parameters effects on electrical conductivity of 3D printed circuits fabricated by direct ink writing method using functionalized multiwalled carbon nanotubes and polyvinyl alcohol conductive ink
Fabrication of electronic circuits and the effects of optimization parameters on electrical conductivity of the printed circuits fabricated by direct ink writing method (D.I.W); one of the novel methods in 3D printing technologies is discussed in this work. This paper focuses on fabrication of electronic circuits using F-MWCNT/PVA conductive ink and analyses the effect of input printing process parameters namely nozzle diameter, extrusion pressure, printing speed on evaluating the electrical conductivity. Box–Behnken approach is followed to generate the levels of experiments and the performance of developed model is assessed using ANOVA. Response surface method is incorporated to find the influencing parameters on electrical conductivity response. Two-point probe measurement method is performed to analyse the output response of the printed electronic circuits. Optimized printing parameters such as nozzle diameter of 0.8 mm, extrusion pressure of 0.1 MPa and printing speed of 4 mm/sec are found to be the best the for printing electronic circuits with high electrical conductivity.
- 21 April 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (3) , 2496-2509
Direct writing of electronic circuits using functionalised multi-walled carbon nanotubes and polyvinyl alcohol conductive ink
Direct Ink writing, one of the types of 3D-printing technologies is a novel method for fabricating electronic circuits. This method of printing electronic circuits is a one-step process and overcomes the limitations of fused deposition modelling where the fabrication of circuits is possible if the material is in filament form and the usage of material is limited to thermoplastic. This work proposes the fabrication of strain gage circuit using functionalised Multi-walled carbon nanotubes (MWCNTs) and Polyvinyl alcohol (PVA) conductive ink by direct writing method. In this work, Fourier-transform infrared analysis is performed to study the existence of functional groups on acid treated MWCNT. According to micro-structural studies, it is observed that MWCNTs were homogeneously distributed. Rheology tests carried out using cone and plate method concluded that the prepared inks exhibited shear thinning behaviour, which is a very important parameter to state the ink made is appropriate for printing electronic circuits. The effects of functionalised MWCNT (a-MWCNT) concentration on the printed strain gage circuitry are analysed using two-point probe method and electrical properties like resistance, resistivity and electrical conductivity are studied. The electrical conductivity of the 3D-printed strain gage circuit is found to be 2.53 × 102 S/m for PVA/a-MWCNT(0.5) ink. Varying the concentration of a-MWCNT, electrical conductivity is observed to be increased to 4.08 × 102 S/m for PVA/a-MWCNT(1.0) and 7.87 × 102 S/m for PVA/a-MWCNT(1.5). Flexibility of PVA and conductivity of a–MWCNT contributed to superior performance of the printed circuit.
- 21 April 2021
- Published by Taylor & Francis in Advances in Materials and Processing Technologies
- Vol. 8 (3) , 2496-2509
Direct writing of electronic circuits using functionalised multi-walled carbon nanotubes and polyvinyl alcohol conductive ink
Direct Ink writing, one of the types of 3D-printing technologies is a novel method for fabricating electronic circuits. This method of printing electronic circuits is a one-step process and overcomes the limitations of fused deposition modelling where the fabrication of circuits is possible if the material is in filament form and the usage of material is limited to thermoplastic. This work proposes the fabrication of strain gage circuit using functionalised Multi-walled carbon nanotubes (MWCNTs) and Polyvinyl alcohol (PVA) conductive ink by direct writing method. In this work, Fourier-transform infrared analysis is performed to study the existence of functional groups on acid treated MWCNT. According to micro-structural studies, it is observed that MWCNTs were homogeneously distributed. Rheology tests carried out using cone and plate method concluded that the prepared inks exhibited shear thinning behaviour, which is a very important parameter to state the ink made is appropriate for printing electronic circuits. The effects of functionalised MWCNT (a-MWCNT) concentration on the printed strain gage circuitry are analysed using two-point probe method and electrical properties like resistance, resistivity and electrical conductivity are studied. The electrical conductivity of the 3D-printed strain gage circuit is found to be 2.53 × 102 S/m for PVA/a-MWCNT(0.5) ink. Varying the concentration of a-MWCNT, electrical conductivity is observed to be increased to 4.08 × 102 S/m for PVA/a-MWCNT(1.0) and 7.87 × 102 S/m for PVA/a-MWCNT(1.5). Flexibility of PVA and conductivity of a–MWCNT contributed to superior performance of the printed circuit.
- 1 January 2020
- Published by ASTM International in Materials Performance and Characterization
- Vol. 9 (1) , 665-674
Direct Ink Writing Method for Manufacturing Electronic Circuits Using Multiwalled Carbon Nanotubes and Polyvinyl Alcohol Composites
Usage of conductive materials for manufacturing electronic circuits using 3D printing methods plays a prominent role in sensing applications and has achieved significant growth in recent years. This growth has led to the development of stretchable, flexible electronics and wearable electronics that are useful as sensing applications in the fields of real-time health monitoring systems. In this paper, a multiwalled carbon nanotube (MWCNT)-based electronic circuit was developed using the 3D printing technique called direct ink writing (DIW). Polyvinyl alcohol (PVA) was used as the binder material to make the MWCNT ink for printing. Different concentrations of MWCNT ink were prepared using 5, 10, and 15 wt. % PVA solutions. The viscosity of MWCNT inks was measured using a rheometer (cone and plate type). The ink exhibited shear thinning behavior, which is suitable for DIW. Finally, the printing of a designed electronic circuit was carried out using a pneumatic extrusion–based 3D printer. The strain sensor circuit—measuring 20 mm long, 9.2 mm wide, and 0.8 mm thick—is manufactured by the 3D printer. Electrical resistivity of strain sensor circuit is evaluated by adopting a two-probe method; the observed resistivity value was 1.7 × 10−2 Ωm for MWCNT ink made with 10 wt. % PVA solution and 1.97 × 10−2 Ωm for MWCNT ink made with 15 wt. % PVA solution.
- 1 January 2020
- Published by ASTM International in Materials Performance and Characterization
- Vol. 9 (1) , 665-674
Direct Ink Writing Method for Manufacturing Electronic Circuits Using Multiwalled Carbon Nanotubes and Polyvinyl Alcohol Composites
Usage of conductive materials for manufacturing electronic circuits using 3D printing methods plays a prominent role in sensing applications and has achieved significant growth in recent years. This growth has led to the development of stretchable, flexible electronics and wearable electronics that are useful as sensing applications in the fields of real-time health monitoring systems. In this paper, a multiwalled carbon nanotube (MWCNT)-based electronic circuit was developed using the 3D printing technique called direct ink writing (DIW). Polyvinyl alcohol (PVA) was used as the binder material to make the MWCNT ink for printing. Different concentrations of MWCNT ink were prepared using 5, 10, and 15 wt. % PVA solutions. The viscosity of MWCNT inks was measured using a rheometer (cone and plate type). The ink exhibited shear thinning behavior, which is suitable for DIW. Finally, the printing of a designed electronic circuit was carried out using a pneumatic extrusion–based 3D printer. The strain sensor circuit—measuring 20 mm long, 9.2 mm wide, and 0.8 mm thick—is manufactured by the 3D printer. Electrical resistivity of strain sensor circuit is evaluated by adopting a two-probe method; the observed resistivity value was 1.7 × 10−2 Ωm for MWCNT ink made with 10 wt. % PVA solution and 1.97 × 10−2 Ωm for MWCNT ink made with 15 wt. % PVA solution.