Hongxi Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hongxi Wang has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Guanwei Wang
School of Mechatronic Engineering, Xi’an Technological University, Xi’an, China
3 shared publications - Wenhong Liang
School of Mechatronic Engineering, Xi’an Technological University, Xi’an, China
3 shared publications Bohan Zhao
2 shared publicationsHui-Hui Tian
School of Mechatronic Engineering , Xi’an Technological University Xi’an , China
2 shared publications- Huihui Tian
School of Mechatronic Engineering, Xi’an Technological University, Xi’an, China
2 shared publications - Jian Zhao
Department of Automotive Engineering, School of Mechanical Engineering, Dalian University of Technology, Dalian, China
2 shared publications
Latest Publications
- 1 August 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (15) , 155228
Engineering design and performance evaluation of a soft crawling robot driven by a rolled dielectric elastomer actuator
Dielectric elastomer actuators (DEA) are lightweight and compliant actuators for soft crawling robots, but converting actuator deformation into stable directional locomotion remains challenging because of structural compliance, passive foot-ground interaction and material hysteresis. In this work, a soft crawling robot driven by a rolled DEA (RDEA) is designed, fabricated and experimentally evaluated. The robot consists of a spring-supported rolled actuator and two passive asymmetric-friction feet, which convert voltage-induced axial deformation into forward crawling motion. An equivalent finite element model of the active rolled actuator was developed in ABAQUS to analyse the voltage-dependent axial deformation under equibiaxial pre-stretching, spring pre-compression and Maxwell-pressure loading. Under a 300% × 300% pre-stretch and a driving voltage of 7 kV, the model predicted an electrostatic deformation ratio of 16.9%, providing the kinematic input for estimating the ideal crawling velocity. A square-wave voltage driving system was then used to evaluate the crawling behaviour of the fabricated prototype under fixed test-surface conditions. The robot reached a maximum measured crawling speed of 4 mm s −1 at 7 kV and 2 Hz, corresponding to approximately 0.04 body lengths per second. The measured velocity was lower than the ideal estimate, mainly because of foot slip, frictional dissipation, structural compliance, dielectric loss and elastomer viscoelasticity. These results indicate that a RDEA combined with passive asymmetric-friction feet provides a simple actuation scheme for compact soft crawling mechanisms, while improvements in foot design, electrical efficiency and long-term motion stability remain necessary.
- 1 August 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (15) , 155228
Engineering design and performance evaluation of a soft crawling robot driven by a rolled dielectric elastomer actuator
Dielectric elastomer actuators (DEA) are lightweight and compliant actuators for soft crawling robots, but converting actuator deformation into stable directional locomotion remains challenging because of structural compliance, passive foot-ground interaction and material hysteresis. In this work, a soft crawling robot driven by a rolled DEA (RDEA) is designed, fabricated and experimentally evaluated. The robot consists of a spring-supported rolled actuator and two passive asymmetric-friction feet, which convert voltage-induced axial deformation into forward crawling motion. An equivalent finite element model of the active rolled actuator was developed in ABAQUS to analyse the voltage-dependent axial deformation under equibiaxial pre-stretching, spring pre-compression and Maxwell-pressure loading. Under a 300% × 300% pre-stretch and a driving voltage of 7 kV, the model predicted an electrostatic deformation ratio of 16.9%, providing the kinematic input for estimating the ideal crawling velocity. A square-wave voltage driving system was then used to evaluate the crawling behaviour of the fabricated prototype under fixed test-surface conditions. The robot reached a maximum measured crawling speed of 4 mm s −1 at 7 kV and 2 Hz, corresponding to approximately 0.04 body lengths per second. The measured velocity was lower than the ideal estimate, mainly because of foot slip, frictional dissipation, structural compliance, dielectric loss and elastomer viscoelasticity. These results indicate that a RDEA combined with passive asymmetric-friction feet provides a simple actuation scheme for compact soft crawling mechanisms, while improvements in foot design, electrical efficiency and long-term motion stability remain necessary.
- Open Access
- 26 August 2025
- Published by MDPI AG in Multimodal Technologies and Interaction
- Vol. 9 (9) , 89
Cognitive Workload Assessment in Aerospace Scenarios: A Cross-Modal Transformer Framework for Multimodal Physiological Signal Fusion
In the field of cognitive workload assessment for aerospace training, existing methods exhibit significant limitations in unimodal feature extraction and in leveraging complementary synergy among multimodal signals, while current fusion paradigms struggle to effectively capture nonlinear dynamic coupling characteristics across modalities. This study proposes DST-Net (Cross-Modal Downsampling Transformer Network), which synergistically integrates pilots’ multimodal physiological signals (electromyography, electrooculography, electrodermal activity) with flight dynamics data through an Anti-Aliasing and Average Pooling LSTM (AAL-LSTM) data fusion strategy combined with cross-modal attention mechanisms. Evaluation on the “CogPilot” dataset for flight task difficulty prediction demonstrates that AAL-LSTM achieves substantial performance improvements over existing approaches (AUC = 0.97, F1 Score = 94.55). Given the dataset’s frequent sensor data missingness, the study further enhances simulated flight experiments. By incorporating eye-tracking features via cross-modal attention mechanisms, the upgraded DST-Net framework achieves even higher performance (AUC = 0.998, F1 Score = 97.95) and reduces the root mean square error (RMSE) of cumulative flight error prediction to 1750. These advancements provide critical support for safety-critical aviation training systems.
- 26 August 2025
- Published by MDPI AG in Multimodal Technologies and Interaction
- Vol. 9 (9) , 89
Open AccessCognitive Workload Assessment in Aerospace Scenarios: A Cross-Modal Transformer Framework for Multimodal Physiological Signal Fusion
In the field of cognitive workload assessment for aerospace training, existing methods exhibit significant limitations in unimodal feature extraction and in leveraging complementary synergy among multimodal signals, while current fusion paradigms struggle to effectively capture nonlinear dynamic coupling characteristics across modalities. This study proposes DST-Net (Cross-Modal Downsampling Transformer Network), which synergistically integrates pilots’ multimodal physiological signals (electromyography, electrooculography, electrodermal activity) with flight dynamics data through an Anti-Aliasing and Average Pooling LSTM (AAL-LSTM) data fusion strategy combined with cross-modal attention mechanisms. Evaluation on the “CogPilot” dataset for flight task difficulty prediction demonstrates that AAL-LSTM achieves substantial performance improvements over existing approaches (AUC = 0.97, F1 Score = 94.55). Given the dataset’s frequent sensor data missingness, the study further enhances simulated flight experiments. By incorporating eye-tracking features via cross-modal attention mechanisms, the upgraded DST-Net framework achieves even higher performance (AUC = 0.998, F1 Score = 97.95) and reduces the root mean square error (RMSE) of cumulative flight error prediction to 1750. These advancements provide critical support for safety-critical aviation training systems.
- 17 June 2025
- Published by Elsevier in Precision Engineering
- Vol. 96, 246-256
A high-reliability acceleration switch based on a compliant bistable mechanism
- 17 June 2025
- Published by Elsevier in Precision Engineering
- Vol. 96, 246-256
A high-reliability acceleration switch based on a compliant bistable mechanism
- 24 October 2024
- Published by Elsevier in Measurement
- Vol. 242
Docking pose analytical calculation method for large components based on draw-wire displacement sensors
- 24 October 2024
- Published by Elsevier in Measurement
- Vol. 242
Docking pose analytical calculation method for large components based on draw-wire displacement sensors
- 27 June 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (9) , 095113
Construction of a measurement system and analytical solution for docking pose of large aircraft components based on draw-wire displacement sensors
Relative pose detection is a key technology in large component automatic docking systems. In this paper, a measurement system has been developed to detect the relative pose of large aircraft components with draw-wire displacement sensors, while an analytical calculation method has been proposed to determine the docking pose of large aircraft components. This method establishes a measurement model for the docking pose of large components and separates the position and orientation solutions based on the distances between seven sets of measurement points measured by the draw-wire displacement sensors. First, the principle of three-dimensional rendezvous positioning is refined to ascertain the relative position of the components. Then, by analyzing the properties of the rotation matrix and the coupling relationship between the position and orientation variables of the movable component, 15 compatible equations containing only two variables with a maximum degree of four are obtained. Based on this set of equations, a unique solution for the rotation matrix was obtained through the variable substitution method, gradually eliminating higher-order terms. Finally, the correctness of the method is verified through numerical examples. Unlike typical parallel mechanism models, this model can directly obtain 15 compatible equations without the need for methods such as Gröbner bases. Moreover, compared to the measurement method using six draw-wire displacement sensors, a unique solution can be directly determined, solving the problem of multiple solution selection. This measurement method only requires measuring the distance between measurement points to solve the relative pose, with low equipment costs and less susceptibility to external environmental factors.
- 27 June 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (9) , 095113
Construction of a measurement system and analytical solution for docking pose of large aircraft components based on draw-wire displacement sensors
Relative pose detection is a key technology in large component automatic docking systems. In this paper, a measurement system has been developed to detect the relative pose of large aircraft components with draw-wire displacement sensors, while an analytical calculation method has been proposed to determine the docking pose of large aircraft components. This method establishes a measurement model for the docking pose of large components and separates the position and orientation solutions based on the distances between seven sets of measurement points measured by the draw-wire displacement sensors. First, the principle of three-dimensional rendezvous positioning is refined to ascertain the relative position of the components. Then, by analyzing the properties of the rotation matrix and the coupling relationship between the position and orientation variables of the movable component, 15 compatible equations containing only two variables with a maximum degree of four are obtained. Based on this set of equations, a unique solution for the rotation matrix was obtained through the variable substitution method, gradually eliminating higher-order terms. Finally, the correctness of the method is verified through numerical examples. Unlike typical parallel mechanism models, this model can directly obtain 15 compatible equations without the need for methods such as Gröbner bases. Moreover, compared to the measurement method using six draw-wire displacement sensors, a unique solution can be directly determined, solving the problem of multiple solution selection. This measurement method only requires measuring the distance between measurement points to solve the relative pose, with low equipment costs and less susceptibility to external environmental factors.
- Open Access
- 1 March 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (3)
Design and analysis of a microgripper for trans-scale clamping based on a compliant multistable mechanism
Piezoelectric actuators commonly used in microgrippers have a small stroke, and their accuracy is reduced by the transmission amplification unit, which leads to a contradiction between the clamping range and the clamping accuracy in existing piezoelectric-actuated microgrippers. This paper proposes a design scheme to divide the total clamping range of the microgripper into segments based on the compliant multistable mechanism (CMM). First, by using the stable equilibrium positions of the CMM, the total clamping range of the microgripper is divided into multiple smaller clamping sub-intervals to accommodate objects of different scales. Then, the theoretical models of the displacement amplification ratio of the microgripper amplification mechanism and the stiffness of the microgripper in different clamping sub-intervals are established, and the force-displacement characteristics of the CMM are analyzed. Next, through finite element simulation, the correctness of the theoretical analyses is verified, and it is shown that objects between 0 µm and 1.650 mm can be clamped using four clamping sub-intervals under a five times displacement amplification ratio. Finally, a microgripper of the CMM consisting of two three-segment fully compliant bistable mechanisms connected in series is designed and machined, and microgripper segmented clamping experiments are conducted. The experimental results demonstrate the feasibility of the design scheme proposed in this paper.
- 1 March 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (3)
Open AccessDesign and analysis of a microgripper for trans-scale clamping based on a compliant multistable mechanism
Piezoelectric actuators commonly used in microgrippers have a small stroke, and their accuracy is reduced by the transmission amplification unit, which leads to a contradiction between the clamping range and the clamping accuracy in existing piezoelectric-actuated microgrippers. This paper proposes a design scheme to divide the total clamping range of the microgripper into segments based on the compliant multistable mechanism (CMM). First, by using the stable equilibrium positions of the CMM, the total clamping range of the microgripper is divided into multiple smaller clamping sub-intervals to accommodate objects of different scales. Then, the theoretical models of the displacement amplification ratio of the microgripper amplification mechanism and the stiffness of the microgripper in different clamping sub-intervals are established, and the force-displacement characteristics of the CMM are analyzed. Next, through finite element simulation, the correctness of the theoretical analyses is verified, and it is shown that objects between 0 µm and 1.650 mm can be clamped using four clamping sub-intervals under a five times displacement amplification ratio. Finally, a microgripper of the CMM consisting of two three-segment fully compliant bistable mechanisms connected in series is designed and machined, and microgripper segmented clamping experiments are conducted. The experimental results demonstrate the feasibility of the design scheme proposed in this paper.
- Open Access
- 1 October 2023
- Published by Walter de Gruyter GmbH in Measurement Science Review
- Vol. 23 (5) , 210-216
Docking Pose Measurement Method for Large Components Based on Draw-Wire Displacement Sensors
A method for measuring the docking pose of large components based on the draw-wire displacement sensor is proposed. In this method, coordinate systems and measurement points are established on the docking surfaces of fixed and moving components. The draw-wire displacement sensor is used to measure the distances between these measurement points. A mathematical model based on the distances between the measurement points is established, and the three-sphere rendezvous positioning principle is optimized to obtain the spatial positions of the measurement points. Consequently, the pose deviations of the fixed and moving components in all six degrees of freedom (6DOF) are determined. A simulation analysis of the measurement uncertainty of the obtained pose deviations is performed, resulting in a composite standard uncertainty obtained from the measurement standard uncertainties of different sensors. The simulation results show that the composite standard uncertainty is most affected in the x-axis translation direction and least affected in the x-axis rotation direction. With this method, only the distances between the measurement points need to be measured to determine the corresponding pose relationships. The cost of the equipment is low, and it is not easily affected by external factors such as the environment.
- 1 October 2023
- Published by Walter de Gruyter GmbH in Measurement Science Review
- Vol. 23 (5) , 210-216
Open AccessDocking Pose Measurement Method for Large Components Based on Draw-Wire Displacement Sensors
A method for measuring the docking pose of large components based on the draw-wire displacement sensor is proposed. In this method, coordinate systems and measurement points are established on the docking surfaces of fixed and moving components. The draw-wire displacement sensor is used to measure the distances between these measurement points. A mathematical model based on the distances between the measurement points is established, and the three-sphere rendezvous positioning principle is optimized to obtain the spatial positions of the measurement points. Consequently, the pose deviations of the fixed and moving components in all six degrees of freedom (6DOF) are determined. A simulation analysis of the measurement uncertainty of the obtained pose deviations is performed, resulting in a composite standard uncertainty obtained from the measurement standard uncertainties of different sensors. The simulation results show that the composite standard uncertainty is most affected in the x-axis translation direction and least affected in the x-axis rotation direction. With this method, only the distances between the measurement points need to be measured to determine the corresponding pose relationships. The cost of the equipment is low, and it is not easily affected by external factors such as the environment.
- Open Access
- 1 April 2023
- Published by Walter de Gruyter GmbH in Measurement Science Review
- Vol. 23 (2) , 72-79
Design and Experimental Study of a Probe for Crankshaft Full-automatic Measuring Machine
The Crankshaft Full-automatic Measuring Machine (CFMM) features high accuracy, high efficiency and complete measurement parameters, and represents the forefront of a geometric crankshaft accuracy measuring instrument. One of its core technologies is the high-precision radial following the crankshaft connecting rod journal measurement. In this paper, an independent probe design scheme combining the flexible dual-complex parallel four-bar guide mechanism and double displacement sensors based on the contact measurement method was proposed. It was suitable for the measurement of precision parts with eccentric characteristics such as crankshaft and camshaft measurement. Taking the spring as the flexible part, the probe prototype’s optimization design, processing and assembly were completed, the test device was built, and the system accuracy was calibrated under various positions and feed quantities of the probe. The results revealed that the expanded measurement uncertainty after double-sensor compensation was enhanced from 1.53 μm in single-sensor measurement to 0.44 μm, satisfying the high-precision requirements of engineering measurement accuracy and reducing the measurement cost.
- 1 April 2023
- Published by Walter de Gruyter GmbH in Measurement Science Review
- Vol. 23 (2) , 72-79
Open AccessDesign and Experimental Study of a Probe for Crankshaft Full-automatic Measuring Machine
The Crankshaft Full-automatic Measuring Machine (CFMM) features high accuracy, high efficiency and complete measurement parameters, and represents the forefront of a geometric crankshaft accuracy measuring instrument. One of its core technologies is the high-precision radial following the crankshaft connecting rod journal measurement. In this paper, an independent probe design scheme combining the flexible dual-complex parallel four-bar guide mechanism and double displacement sensors based on the contact measurement method was proposed. It was suitable for the measurement of precision parts with eccentric characteristics such as crankshaft and camshaft measurement. Taking the spring as the flexible part, the probe prototype’s optimization design, processing and assembly were completed, the test device was built, and the system accuracy was calibrated under various positions and feed quantities of the probe. The results revealed that the expanded measurement uncertainty after double-sensor compensation was enhanced from 1.53 μm in single-sensor measurement to 0.44 μm, satisfying the high-precision requirements of engineering measurement accuracy and reducing the measurement cost.
- Open Access
Dynamic Programming BN Structure Learning Algorithm Integrating Double Constraints under Small Sample Condition
The Bayesian Network (BN) structure learning algorithm based on dynamic programming can obtain global optimal solutions. However, when the sample cannot fully contain the information of the real structure, especially when the sample size is small, the obtained structure is inaccurate. Therefore, this paper studies the planning mode and connotation of dynamic programming, restricts its process with edge and path constraints, and proposes a dynamic programming BN structure learning algorithm with double constraints under small sample conditions. The algorithm uses double constraints to limit the planning process of dynamic programming and reduces the planning space. Then, it uses double constraints to limit the selection of the optimal parent node to ensure that the optimal structure conforms to prior knowledge. Finally, the integrating prior-knowledge method and the non-integrating prior-knowledge method are simulated and compared. The simulation results verify the effectiveness of the method proposed and prove that the integrating prior knowledge can significantly improve the efficiency and accuracy of BN structure learning.
Open AccessDynamic Programming BN Structure Learning Algorithm Integrating Double Constraints under Small Sample Condition
The Bayesian Network (BN) structure learning algorithm based on dynamic programming can obtain global optimal solutions. However, when the sample cannot fully contain the information of the real structure, especially when the sample size is small, the obtained structure is inaccurate. Therefore, this paper studies the planning mode and connotation of dynamic programming, restricts its process with edge and path constraints, and proposes a dynamic programming BN structure learning algorithm with double constraints under small sample conditions. The algorithm uses double constraints to limit the planning process of dynamic programming and reduces the planning space. Then, it uses double constraints to limit the selection of the optimal parent node to ensure that the optimal structure conforms to prior knowledge. Finally, the integrating prior-knowledge method and the non-integrating prior-knowledge method are simulated and compared. The simulation results verify the effectiveness of the method proposed and prove that the integrating prior knowledge can significantly improve the efficiency and accuracy of BN structure learning.