Dandan Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Dandan Li has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Qichi Le
The Key Laboratory of Electromagnetic Processing of Materials Ministry of Education Northeastern University Shenyang 110819 China
5 shared publicationsXiaoqiang Li
4 shared publicationsChenglu Hu
3 shared publicationsPing Wang
3 shared publicationsXiong Zhou
3 shared publicationsDexue Liu
School of Materials Science and Engineering Lanzhou University of Technology Lanzhou 730050 China
2 shared publications
Latest Publications
- 2 September 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (21)
The Influence of Bending Temperature on the Bending Formability and Microstructure of Mg‐2Zn‐Based Alloy Thin‐Walled Tubes
Strong basal textures in magnesium alloy tubes impair their secondary formability. This study developed Mg‐2Zn‐0.4Ce‐0.4Mn‐0.2Ca (ZMEX, 2#) thin‐walled magnesium alloy tubes with both low cost and weak texture through micro‐alloying with Ce and Ca. Mg‐2Zn‐0.4Ce‐0.4Mn (ZME, 1#) tubes serve as the control group. The microstructure and bendability of both tubes are investigated at different bending temperatures. Results indicate that cracking occurred on the upper walls of both alloys during room temperature bending, though the severity is lower in the 2# tube than in the 1# tube. As bending temperature increases, cracking disappears in both alloys. Their peak load displacement (PLD) and maximum bending displacement (MBD) values gradually rise, while total energy absorption (TEA) shows an initial increase followed by a decrease. Compared to the 1# tube, the 2# tube demonstrates superior bending formability, particularly at 200 °C (PLD, 14.5 ± 0.5 mm; MBD, 45.0 ± 3.3 mm; TEA, 142.9 ± 1.7 J). Electron backscattered diffraction analysis reveals that the enhanced bending performance of the 2# tube primarily stem from weak texture promoting slip activity, refined grain size, and Zn/Ca elemental segregation at grain boundaries. This study provides a theoretical basis for developing magnesium alloy tubes with good secondary formability.
- 2 September 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (21)
The Influence of Bending Temperature on the Bending Formability and Microstructure of Mg‐2Zn‐Based Alloy Thin‐Walled Tubes
Strong basal textures in magnesium alloy tubes impair their secondary formability. This study developed Mg‐2Zn‐0.4Ce‐0.4Mn‐0.2Ca (ZMEX, 2#) thin‐walled magnesium alloy tubes with both low cost and weak texture through micro‐alloying with Ce and Ca. Mg‐2Zn‐0.4Ce‐0.4Mn (ZME, 1#) tubes serve as the control group. The microstructure and bendability of both tubes are investigated at different bending temperatures. Results indicate that cracking occurred on the upper walls of both alloys during room temperature bending, though the severity is lower in the 2# tube than in the 1# tube. As bending temperature increases, cracking disappears in both alloys. Their peak load displacement (PLD) and maximum bending displacement (MBD) values gradually rise, while total energy absorption (TEA) shows an initial increase followed by a decrease. Compared to the 1# tube, the 2# tube demonstrates superior bending formability, particularly at 200 °C (PLD, 14.5 ± 0.5 mm; MBD, 45.0 ± 3.3 mm; TEA, 142.9 ± 1.7 J). Electron backscattered diffraction analysis reveals that the enhanced bending performance of the 2# tube primarily stem from weak texture promoting slip activity, refined grain size, and Zn/Ca elemental segregation at grain boundaries. This study provides a theoretical basis for developing magnesium alloy tubes with good secondary formability.
- Open Access
- 10 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 6902-6913
Research on predicting the thermocompression deformation behavior of Mg–Li matrix composite using machine learning and traditional techniques
- 10 November 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 33, 6902-6913
Open AccessResearch on predicting the thermocompression deformation behavior of Mg–Li matrix composite using machine learning and traditional techniques
- Open Access
- 1 March 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (3) , 1054-1067
Study on the low mechanical anisotropy of extruded Mg-Zn-Mn-Ce-Ca alloy tube in the compression process
- 1 March 2024
- Published by KEAI Publishing in Journal of Magnesium and Alloys
- Vol. 12 (3) , 1054-1067
Open AccessStudy on the low mechanical anisotropy of extruded Mg-Zn-Mn-Ce-Ca alloy tube in the compression process
- Open Access
- 19 August 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 20, 3485-3498
The influence of initial texture, microstructure and deformation behavior on the low mechanical anisotropy of extruded Mg alloy tube
- 19 August 2022
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 20, 3485-3498
Open AccessThe influence of initial texture, microstructure and deformation behavior on the low mechanical anisotropy of extruded Mg alloy tube