Smail Chtita
Smail Chtita has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
Abdelaziz El Ghzizal
EST SMBA University Fez Morocco
2 shared publications- Aziz Derouich
Sidi Mohamed Ben Abdellah University
2 shared publications - Saad Motahhir
National School of Applied Sciences of Fez, Sidi Mohamed Ben Abdellah University, Fez, Morocco
2 shared publications - Badre El Majid
Independent Scientist, Rabat, Morocco
1 shared publication Jamal Belkadid
Laboratory of Transmission and Processing Information, Laboratory of Transmission and Processing Information, Fez, Morocco
1 shared publicationSaad Motahhir
ENSA SMBA University Fez Morocco
1 shared publication
Latest Publications
- 12 October 2024
- Published by Springer Nature in Euro-Mediterranean Journal for Environmental Integration
- Vol. 10 (1) , 281-289
Automated cleaning of solar panels using a three-rotor drone
- 12 October 2024
- Published by Springer Nature in Euro-Mediterranean Journal for Environmental Integration
- Vol. 10 (1) , 281-289
Automated cleaning of solar panels using a three-rotor drone
- 12 January 2024
- Published by Wiley in Energy Technology
- Vol. 12 (4)
A New Design and Embedded Implementation of a Low‐Cost Maximum Power Point Tracking Charge Controller for Stand‐Alone Photovoltaic Systems
This article presents a low‐cost maximum power point tracking (MPPT) charge controller designed to efficiently charge solar batteries using a simple and robust MPPT method, while providing protection against over‐currents and over‐voltages. The proposed MPPT approach utilizes a modified Incremental Conductance (INC) algorithm adapted to low‐cost embedded controllers, as it avoids all the mathematical division calculations typically used in the conventional INC algorithm. It also introduces a modified step size based only on photovoltaic (PV) power change to enhance tracking accuracy and convergence speed. Furthermore, to reduce the stress and switching losses of DC–DC converter, a feedback control with two proportional and integral (PI) compensators is also used to control both the PV voltage and to protect the battery from over‐currents using PV power limitation technique. Simulation results, carried out under MATLAB/Simulink, demonstrate the good performance of the proposed control scheme regarding any variations in atmospheric conditions, both for the MPPT control and for the battery charge control. Finally, a processor‐in‐the‐loop (PIL) test using a low‐cost Arduino MKR ZERO board is also performed to verify the hardware implementation of the proposed method. PIL results are in totally accordance with MATLAB/Simulink simulation results, which further proves the effectiveness of the proposed method.
- 12 January 2024
- Published by Wiley in Energy Technology
- Vol. 12 (4)
A New Design and Embedded Implementation of a Low‐Cost Maximum Power Point Tracking Charge Controller for Stand‐Alone Photovoltaic Systems
This article presents a low‐cost maximum power point tracking (MPPT) charge controller designed to efficiently charge solar batteries using a simple and robust MPPT method, while providing protection against over‐currents and over‐voltages. The proposed MPPT approach utilizes a modified Incremental Conductance (INC) algorithm adapted to low‐cost embedded controllers, as it avoids all the mathematical division calculations typically used in the conventional INC algorithm. It also introduces a modified step size based only on photovoltaic (PV) power change to enhance tracking accuracy and convergence speed. Furthermore, to reduce the stress and switching losses of DC–DC converter, a feedback control with two proportional and integral (PI) compensators is also used to control both the PV voltage and to protect the battery from over‐currents using PV power limitation technique. Simulation results, carried out under MATLAB/Simulink, demonstrate the good performance of the proposed control scheme regarding any variations in atmospheric conditions, both for the MPPT control and for the battery charge control. Finally, a processor‐in‐the‐loop (PIL) test using a low‐cost Arduino MKR ZERO board is also performed to verify the hardware implementation of the proposed method. PIL results are in totally accordance with MATLAB/Simulink simulation results, which further proves the effectiveness of the proposed method.
- 1 May 2021
- Published by Elsevier in Solar Energy
- Vol. 220, 927-941
An improved control strategy for charging solar batteries in off-grid photovoltaic systems
- 1 May 2021
- Published by Elsevier in Solar Energy
- Vol. 220, 927-941
An improved control strategy for charging solar batteries in off-grid photovoltaic systems
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Modeling and Simulation of a Photovoltaic Panel Based on a Triple Junction Cells for a Nanosatellite
This paper gives a simplified modelling of a Photovoltaic (PV) panel used in nanosatellite applications. For this reason, a single diode equivalent circuit model is proposed. Thereafter, a description of the triple-junction cell is presented. Then, the parameters extraction process of the used PV cell equivalent circuit is performed. In order to study the electrical performance of the equivalent circuit model, the nominal values provided by the manufacturer, namely: open circuit voltage, short-circuit current, the maximum power voltage and current are used to extract the unknown parameters ( Iph, Irs, R s , nand Rsh) using mathematical equations. The novelty of this work is a modelling and a simulation of a Nanosatellite PV panel. In order to accurate the results, the extracted current-voltage (I-V) and power-voltage (P-V) characteristics are compared to the provided ones from Psim Software for various levels of irradiance and temperature corresponding to the solar spectrum outside the AM0 atmosphere. The proposed method presents high performance and simple behavior which makes it applicable for the nanosatellite panels.
- 1 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Modeling and Simulation of a Photovoltaic Panel Based on a Triple Junction Cells for a Nanosatellite
This paper gives a simplified modelling of a Photovoltaic (PV) panel used in nanosatellite applications. For this reason, a single diode equivalent circuit model is proposed. Thereafter, a description of the triple-junction cell is presented. Then, the parameters extraction process of the used PV cell equivalent circuit is performed. In order to study the electrical performance of the equivalent circuit model, the nominal values provided by the manufacturer, namely: open circuit voltage, short-circuit current, the maximum power voltage and current are used to extract the unknown parameters ( Iph, Irs, R s , nand Rsh) using mathematical equations. The novelty of this work is a modelling and a simulation of a Nanosatellite PV panel. In order to accurate the results, the extracted current-voltage (I-V) and power-voltage (P-V) characteristics are compared to the provided ones from Psim Software for various levels of irradiance and temperature corresponding to the solar spectrum outside the AM0 atmosphere. The proposed method presents high performance and simple behavior which makes it applicable for the nanosatellite panels.