Riccardo Barbone
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Riccardo Barbone has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Mattia Ricco
University of Bologna
5 shared publications - Riccardo Mandrioli
University of Bologna
5 shared publications - Gabriele Grandi
Department of Electrical, Electronic, and Information Engineering, University of Bologna, 40136 Bologna, Italy
3 shared publications - Vincenzo Cirimele
Department of Electrical, Electronic and Information Engineering, University of Bologna, 40136 Bologna, Italy
3 shared publications - Rudolf Francesco Paternost
Department of Electrical, Electronic, and Information Engineering, University of Bologna, 40136 Bologna, Italy
2 shared publications - Aleksandr Viatkin
Hitachi Energy Sweden AB
1 shared publication
Latest Publications
- Open Access
- 15 October 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Computational cost reduction in electric traction network modelling and simulation
- 15 October 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Open AccessComputational cost reduction in electric traction network modelling and simulation
- Open Access
- 6 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 35022-35034
Development of a High-Precision and Flexible Model for Accurate Simulation of Trolleybus Grids
The reduction of climate-changing emissions is vital, particularly in urban areas. To achieve this goal, the decarbonization of the transport sector is decisive. Trolleybus systems represent a solution towards sustainability as long as the integration of the electrical infrastructure with renewable sources as well as the introduction of full-electric fleets are actualized. To ensure a smart electrical transition the circuit modelling phase is crucial and must enable the most accurate simulations possible. The modularity of the catenary model and a versatile graphical user interface, which allows extensive topological change flexibility, distinguish the novel trolleybus network simulator presented in this study. The model completes the gaps left by earlier block-based simulation tools with its high precision and low processing effort. The suggested model’s enhancement in precision is evidenced by a graphical study of the voltage distribution examined in a section of Bologna’s trolleybus grid. Finally, albeit non-iterative and thus computationally even cheaper, the proposed model is applicable for the simulation of more complex realistic scenarios involving the non-linearity of the equivalent power grid. The article will show satisfactory results on the convergence of the simulator.
- 6 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 35022-35034
Open AccessDevelopment of a High-Precision and Flexible Model for Accurate Simulation of Trolleybus Grids
The reduction of climate-changing emissions is vital, particularly in urban areas. To achieve this goal, the decarbonization of the transport sector is decisive. Trolleybus systems represent a solution towards sustainability as long as the integration of the electrical infrastructure with renewable sources as well as the introduction of full-electric fleets are actualized. To ensure a smart electrical transition the circuit modelling phase is crucial and must enable the most accurate simulations possible. The modularity of the catenary model and a versatile graphical user interface, which allows extensive topological change flexibility, distinguish the novel trolleybus network simulator presented in this study. The model completes the gaps left by earlier block-based simulation tools with its high precision and low processing effort. The suggested model’s enhancement in precision is evidenced by a graphical study of the voltage distribution examined in a section of Bologna’s trolleybus grid. Finally, albeit non-iterative and thus computationally even cheaper, the proposed model is applicable for the simulation of more complex realistic scenarios involving the non-linearity of the equivalent power grid. The article will show satisfactory results on the convergence of the simulator.
- Open Access
- 13 September 2022
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 13 (9) , 169
Catenary-Powered Electric Traction Network Modeling: A Data-Driven Analysis for Trolleybus System Simulation
In the context of smart cities, direct current overhead contact lines, usually adopted to power urban transportation systems such as trolleybuses, tramways, metros, and railways, can serve as a backbone to connect different modern emerging technologies. Among these, in-motion charging (IMC) trolleybuses with on-board batteries are expected to be very impactful on the DC network’s power flow and may require specific voltage and current control. These factors motivate the development of a simulation tool able to emulate these devices’ absorption and their effect on the supply infrastructure. The main innovative value of the work is to improve a simulation model of a trolleybus grid through a data-driven approach by using measurements of voltage and current output from a traction substation. The measurements are essential for understanding the behavior of vehicle weight variation throughout the day. Thanks to this information, a characterization of the current draw by conventional trolleybuses and IMC trolleybuses is then provided for each trolleybus route in a specific power section of the Bologna trolleybus system. By integrating the variation in vehicle weight within the model, a simulation of a possible daily operation of a trolleybus feeding section has been performed, obtaining a 7% error between the daily energy calculated from the simulation and that obtained through measurements. This analysis demonstrates the feasibility of the adopted simulation tool, which can also be used to evaluate additional hypothetical trolleybus operation scenarios. One of these possible scenarios considers IMC vehicles, and it is also evaluated in this paper.
- 13 September 2022
- Published by MDPI AG in World Electric Vehicle Journal
- Vol. 13 (9) , 169
Open AccessCatenary-Powered Electric Traction Network Modeling: A Data-Driven Analysis for Trolleybus System Simulation
In the context of smart cities, direct current overhead contact lines, usually adopted to power urban transportation systems such as trolleybuses, tramways, metros, and railways, can serve as a backbone to connect different modern emerging technologies. Among these, in-motion charging (IMC) trolleybuses with on-board batteries are expected to be very impactful on the DC network’s power flow and may require specific voltage and current control. These factors motivate the development of a simulation tool able to emulate these devices’ absorption and their effect on the supply infrastructure. The main innovative value of the work is to improve a simulation model of a trolleybus grid through a data-driven approach by using measurements of voltage and current output from a traction substation. The measurements are essential for understanding the behavior of vehicle weight variation throughout the day. Thanks to this information, a characterization of the current draw by conventional trolleybuses and IMC trolleybuses is then provided for each trolleybus route in a specific power section of the Bologna trolleybus system. By integrating the variation in vehicle weight within the model, a simulation of a possible daily operation of a trolleybus feeding section has been performed, obtaining a 7% error between the daily energy calculated from the simulation and that obtained through measurements. This analysis demonstrates the feasibility of the adopted simulation tool, which can also be used to evaluate additional hypothetical trolleybus operation scenarios. One of these possible scenarios considers IMC vehicles, and it is also evaluated in this paper.
- Open Access
- 15 March 2022
- Published by MDPI AG in Electronics
- Vol. 11 (6) , 915
Novel Multi-Vehicle Motion-Based Model of Trolleybus Grids towards Smarter Urban Mobility
Trolleybus systems are resurfacing as a steppingstone to carbon-neutral urban transport. With an eye on smart city evolution, the study and simulation of a proper monitoring system for trolleybus infrastructures will be essential. This paper merges the authors’ engineering knowledge and sources available in the literature on designing and modeling catenary-based electric traction networks and performs a critical review of them to lay the foundations for proposing possible optimal alternatives. A novel multi-vehicle motion-based model of the DC catenary system is then devised and simulated in Matlab-Simulink, which could prove useful in predicting possible technical obstacles arising from the next-future introduction of smart electric traction grids, inevitably featuring greater morphological intricacy. The modularity property characterizing the created model allows an accurate, detailed, and flexible simulation of sophisticated catenary systems. By means of graphical and numerical results illustrating the behavior of the main electrical line parameters, the presented approach demonstrates today’s obsolescence of conventional design methods used so far. The trolleybus network of the city of Bologna was chosen as a case study.
- 15 March 2022
- Published by MDPI AG in Electronics
- Vol. 11 (6) , 915
Open AccessNovel Multi-Vehicle Motion-Based Model of Trolleybus Grids towards Smarter Urban Mobility
Trolleybus systems are resurfacing as a steppingstone to carbon-neutral urban transport. With an eye on smart city evolution, the study and simulation of a proper monitoring system for trolleybus infrastructures will be essential. This paper merges the authors’ engineering knowledge and sources available in the literature on designing and modeling catenary-based electric traction networks and performs a critical review of them to lay the foundations for proposing possible optimal alternatives. A novel multi-vehicle motion-based model of the DC catenary system is then devised and simulated in Matlab-Simulink, which could prove useful in predicting possible technical obstacles arising from the next-future introduction of smart electric traction grids, inevitably featuring greater morphological intricacy. The modularity property characterizing the created model allows an accurate, detailed, and flexible simulation of sophisticated catenary systems. By means of graphical and numerical results illustrating the behavior of the main electrical line parameters, the presented approach demonstrates today’s obsolescence of conventional design methods used so far. The trolleybus network of the city of Bologna was chosen as a case study.
- Open Access
- 24 April 2021
- Published by MDPI AG in Electronics
- Vol. 10 (9) , 1016
Phase and Neutral Current Ripple Analysis in Three-Phase Four-Wire Split-Capacitor Grid Converter for EV Chargers
The current switching ripple in a three-phase four-wire split-capacitor converter is analyzed in this paper for all the four ac output wires in relation to both balanced and unbalanced working conditions. Specifically, analytical formulations of the peak-to-peak and root mean square (RMS) current ripples are originally evaluated as a function of the modulation index, separately for the three phases and the neutral wire. Initially, the single-carrier sinusoidal pulse width modulation (PWM) technique is outlined, as it generally concerns a straightforward and effective modulation. With the aim of mitigating the current ripple in the neutral wire, the interleaved multiple-carrier PWM strategy is adopted, also avoiding any repercussion on the phase one. Numerical simulations and experimental tests were carried out to verify all the analytical developments.
- 24 April 2021
- Published by MDPI AG in Electronics
- Vol. 10 (9) , 1016
Open AccessPhase and Neutral Current Ripple Analysis in Three-Phase Four-Wire Split-Capacitor Grid Converter for EV Chargers
The current switching ripple in a three-phase four-wire split-capacitor converter is analyzed in this paper for all the four ac output wires in relation to both balanced and unbalanced working conditions. Specifically, analytical formulations of the peak-to-peak and root mean square (RMS) current ripples are originally evaluated as a function of the modulation index, separately for the three phases and the neutral wire. Initially, the single-carrier sinusoidal pulse width modulation (PWM) technique is outlined, as it generally concerns a straightforward and effective modulation. With the aim of mitigating the current ripple in the neutral wire, the interleaved multiple-carrier PWM strategy is adopted, also avoiding any repercussion on the phase one. Numerical simulations and experimental tests were carried out to verify all the analytical developments.