Hao Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hao Li has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Yinglin Ke
State Key Laboratory of Fluid Power and Mechatronic System, School of Mechanical Engineering, Zhejiang University, Hangzhou, China
3 shared publicationsLingyun Wang
State Key Laboratory of Fluid Power and Mechatronic System, School of Mechanical Engineering, Zhejiang University, Hangzhou, China
2 shared publications- Qiang Xu
State Key Laboratory of Fluid Power and Mechatronic System, School of Mechanical Engineering, Zhejiang University, Hangzhou, China
2 shared publications Junxia Jiang
State Key Laboratory of Fluid Power and Mechatronic Systems, School of Mechanical Engineering, Zhejiang University, Hangzhou, China
1 shared publication- Ning Li
Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Dalian, 116023, China
1 shared publication - Tiancheng Huang
College of Computing and Data Science, Nanyang Technological University
1 shared publication
Latest Publications
- 16 September 2022
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 56 (27) , 4101-4112
Optimization of the curing cycle for the large-scale composite stiffened panel based on the response surface methodology and Fgoalattain algorithm
The autoclave curing process of the large-scale composite stiffened panel greatly affects the manufacturing quality of the component, especially the curing quality of stiffeners and the bonding quality between stiffeners and the panel. In this paper, a multi-objective optimization method is developed to optimize the curing cycle for the composite T-stiffened fuselage panel, which aims to minimize the temperature difference within the component to achieve better forming quality. The autoclave curing model considering thermal properties of composites is established and verified by the experiment first. The response surface models are then built up with the Finite Element Method (FEM) and the Box-Behnken Design (BBD). The fgoalattain algorithm is applied to solve the multi-objective optimization problem with nonlinear constraints. Results show that the maximum temperature difference of the two groups of monitoring points decreases by 22.91% and 21.42%, respectively. Besides, the total curing time is also reduced by 11 mins.
- 16 September 2022
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 56 (27) , 4101-4112
Optimization of the curing cycle for the large-scale composite stiffened panel based on the response surface methodology and Fgoalattain algorithm
The autoclave curing process of the large-scale composite stiffened panel greatly affects the manufacturing quality of the component, especially the curing quality of stiffeners and the bonding quality between stiffeners and the panel. In this paper, a multi-objective optimization method is developed to optimize the curing cycle for the composite T-stiffened fuselage panel, which aims to minimize the temperature difference within the component to achieve better forming quality. The autoclave curing model considering thermal properties of composites is established and verified by the experiment first. The response surface models are then built up with the Finite Element Method (FEM) and the Box-Behnken Design (BBD). The fgoalattain algorithm is applied to solve the multi-objective optimization problem with nonlinear constraints. Results show that the maximum temperature difference of the two groups of monitoring points decreases by 22.91% and 21.42%, respectively. Besides, the total curing time is also reduced by 11 mins.
- 3 May 2022
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 42 (1-2) , 17-25
A manta-ray-inspired bionic curing mold for autoclave process of composite manufacturing
The temperature distribution of the mold is directly linked to the manufacturing quality of the composite component. In this paper, a bionic mold based on the analysis of a manta ray in swimming is developed to improve the thermal performance of the mold during the autoclave curing process. The bionic mold has fewer frames and better air permeability, and the mold weight is decreased by 42.95% while the stiffness is proved to satisfy the requirement. The model of the autoclave curing process which is verified by experiments is established to carry out the thermal analysis of the mold. Results show that the air velocity in the mold is increased with the bionic design, which can reduce not only the maximum temperature difference of the mold plate (−30.35%) but also the percentage of low-temperature areas. Besides, the heating rate and the heat preservation time of the mold are also improved.
- 3 May 2022
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 42 (1-2) , 17-25
A manta-ray-inspired bionic curing mold for autoclave process of composite manufacturing
The temperature distribution of the mold is directly linked to the manufacturing quality of the composite component. In this paper, a bionic mold based on the analysis of a manta ray in swimming is developed to improve the thermal performance of the mold during the autoclave curing process. The bionic mold has fewer frames and better air permeability, and the mold weight is decreased by 42.95% while the stiffness is proved to satisfy the requirement. The model of the autoclave curing process which is verified by experiments is established to carry out the thermal analysis of the mold. Results show that the air velocity in the mold is increased with the bionic design, which can reduce not only the maximum temperature difference of the mold plate (−30.35%) but also the percentage of low-temperature areas. Besides, the heating rate and the heat preservation time of the mold are also improved.
- 21 April 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 236 (1) , 183-190
Design and analysis of the mandrel structure for a composite S-shaped inlet
Automated fiber placement (AFP) combining with the autoclave curing process is the main manufacturing method for large-scale rotary composite parts. During the forming process, the mandrel plays an important role that affects the forming quality of the part directly. In this study, design and analysis of the mandrel structure for a composite S-shaped inlet are carried out. The preforming process of the rotary composite part using the AFP technique is introduced first. Then, design principles of the shaft are presented and applied to the shaft design for the mandrel of the S-shaped inlet, which then is transformed into an optimization problem. The internal penalty function method is adopted to solve this optimization problem in order to obtain the optimal axis position and axle diameter. Moreover, detailed structure design of the mandrel is proposed which takes the demolding into consideration, and the wall thickness is designed considering the total weight and the stiffness. The static analysis and modal analysis are also carried out by the finite element method to verify the feasibility of the proposed mandrel structure.
- 21 April 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering
- Vol. 236 (1) , 183-190
Design and analysis of the mandrel structure for a composite S-shaped inlet
Automated fiber placement (AFP) combining with the autoclave curing process is the main manufacturing method for large-scale rotary composite parts. During the forming process, the mandrel plays an important role that affects the forming quality of the part directly. In this study, design and analysis of the mandrel structure for a composite S-shaped inlet are carried out. The preforming process of the rotary composite part using the AFP technique is introduced first. Then, design principles of the shaft are presented and applied to the shaft design for the mandrel of the S-shaped inlet, which then is transformed into an optimization problem. The internal penalty function method is adopted to solve this optimization problem in order to obtain the optimal axis position and axle diameter. Moreover, detailed structure design of the mandrel is proposed which takes the demolding into consideration, and the wall thickness is designed considering the total weight and the stiffness. The static analysis and modal analysis are also carried out by the finite element method to verify the feasibility of the proposed mandrel structure.
- 17 August 2019
- Published by Springer Nature
- p. 769-777
Digital Human Modeling for Performance Evaluation During Marine Vehicle Operation
- 17 August 2019
- Published by Springer Nature
- p. 769-777
Digital Human Modeling for Performance Evaluation During Marine Vehicle Operation