Rabeb Belghouthi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Rabeb Belghouthi has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Amani Rached
Department of Physics, College of Science, Imam Abdulrahman Bin Faisel University, City of Dammam, Saudi Arabia
1 shared publication- Hafedh Belmabrouk
Department of Physics, College of Science Majmaah University Al Majma'ah Saudi Arabia
1 shared publication - Jean Paul Salvestrini
CNRS, Georgia Tech—CNRS International Research Lab 1 , 2958, 2 rue Marconi, 57070 Metz
1 shared publication - Khaoula Amri
LMOPS, Université de Lorraine, CentraleSupélec, F-57000 Metz, France
1 shared publication Michel Aillerie
Laboratoire Matériaux Optiques, Photonique et Systèmes, LMOPS, EA 4423, Université de Lorraine, Metz, France
1 shared publication- Michel Aillerie
Affiliation Laboratoire Matériaux Optiques, Photonique et Systèmes (LMOPS), Université de Lorraine & CentraleSupélec, Metz, France
1 shared publication
Latest Publications
- 2 May 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (7) , 5299-5311
Numerical Investigation of Piezoelectric Potential of Nanowire for Solar Energy Harvesting Using InGaN
- 2 May 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (7) , 5299-5311
Numerical Investigation of Piezoelectric Potential of Nanowire for Solar Energy Harvesting Using InGaN
- 2 September 2023
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 52 (11) , 7566-7575
N-Face Semi-Bulk Absorber Boosts Conversion Efficiency of InGaN Solar Cell
- 2 September 2023
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 52 (11) , 7566-7575
N-Face Semi-Bulk Absorber Boosts Conversion Efficiency of InGaN Solar Cell
- Open Access
Device Optimization of a Lead-Free Perovskite/Silicon Tandem Solar Cell with 24.4% Power Conversion Efficiency
In this work, simulations were performed to optimize the parameters of a lead-free perovskite/silicon tandem solar cell for the improved efficiency and stability of commercial devices. The top sub-cell is based on a lead-free perovskite with a large bandgap of 1.8 eV, an electron transport layer of SnO2/PCBM, which is known for its anti-hysteresis effect, and a hole transport layer of NiO to improve stability, whereas the bottom sub-cell is based on n-type silicon to increase the efficiency of the whole cell. First, the two sub-cells were simulated under standalone conditions for calibration purposes. Then, the current matching condition was obtained by optimizing the thicknesses of the absorber layers of both sub-cells and the doping concentration of the back surface field (BSF) layer of the silicon sub-cell. As a result of this optimization phase, thicknesses of 380 nm and 20 µm for the top and bottom sub-cells, respectively, and a doping concentration of 1022 cm–3 were used in the configuration of the tandem cell, yielding a large open-circuit voltage of 1.76 V and a power conversion efficiency of 24.4% for the whole cell. Finally, the effect of the working temperature was evaluated, and the results reveal that the high performance of lead-free perovskite sub-cells is less affected by an increase in temperature compared to lead-based solar cells, such as those based on CH3NH3PbI3 perovskite.
Open AccessDevice Optimization of a Lead-Free Perovskite/Silicon Tandem Solar Cell with 24.4% Power Conversion Efficiency
In this work, simulations were performed to optimize the parameters of a lead-free perovskite/silicon tandem solar cell for the improved efficiency and stability of commercial devices. The top sub-cell is based on a lead-free perovskite with a large bandgap of 1.8 eV, an electron transport layer of SnO2/PCBM, which is known for its anti-hysteresis effect, and a hole transport layer of NiO to improve stability, whereas the bottom sub-cell is based on n-type silicon to increase the efficiency of the whole cell. First, the two sub-cells were simulated under standalone conditions for calibration purposes. Then, the current matching condition was obtained by optimizing the thicknesses of the absorber layers of both sub-cells and the doping concentration of the back surface field (BSF) layer of the silicon sub-cell. As a result of this optimization phase, thicknesses of 380 nm and 20 µm for the top and bottom sub-cells, respectively, and a doping concentration of 1022 cm–3 were used in the configuration of the tandem cell, yielding a large open-circuit voltage of 1.76 V and a power conversion efficiency of 24.4% for the whole cell. Finally, the effect of the working temperature was evaluated, and the results reveal that the high performance of lead-free perovskite sub-cells is less affected by an increase in temperature compared to lead-based solar cells, such as those based on CH3NH3PbI3 perovskite.
- 25 November 2017
- Published by Springer Nature
- p. 1-9
Enhancing Efficiency of InGaN Nanowire Solar Cells by Applying Stress
- 25 November 2017
- Published by Springer Nature
- p. 1-9
Enhancing Efficiency of InGaN Nanowire Solar Cells by Applying Stress