Jian Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jian Li has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Cuiyong Tang
College of Mechanical and Electrical Engineering, Fujian Agriculture and Forestry University, Fuzhou 350002, China
2 shared publications Peng Zou
National Key Laboratory of Strength and Structural Integrity, Aircraft Strength Research Institute of China, Xi’an, China
2 shared publicationsHaibo Li
College of Mechanical and Electrical Engineering, Fujian Agriculture and Forestry University, Fuzhou, People’s Republic of China
1 shared publicationJianfeng Wen
School of Mechanical and Power Engineering, East China University of Science and Technology, Shanghai, China
1 shared publication- Peng Zou
National Key Laboratory of Strength and Structural Integrity Aircraft Strength Research Institute of China Xi'an Shaanxi China
1 shared publication Pengwan Zhu
School of Physics and Electromechanical Engineering, Longyan University, Longyan, China
1 shared publication
Latest Publications
- 27 October 2026
- Published by Springer Nature in JOM
- p. 1-13
Optimization of Process Parameters for Laser-Cladded Fe-Based Amorphous Alloy Composite Coatings via Response Surface Methodology
- 27 October 2026
- Published by Springer Nature in JOM
- p. 1-13
Optimization of Process Parameters for Laser-Cladded Fe-Based Amorphous Alloy Composite Coatings via Response Surface Methodology
- Open Access
- 27 April 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (4)
Effect of imbalanced interface pre-tightening force on the bearing behavior of carbon fiber reinforced polymer interference-fit lap joint
Interference-fit is attracting increasing attention in the aerospace field because of its excellent enhancement of the sealing and fatigue life of carbon fiber reinforced plastic (CFRP). However, it also induces imbalanced pre-tightening forces on the interface, and affects its mechanical behavior. A series of experiments were conducted to assess the imbalanced pre-tightening force of CFRP interference bolted joints and its effects. High-precision washer force sensors were used to measure the pre-tightening force between upper and lower surfaces at various interference-fit and torque. Strain gauges were used to estimate the varying effect on the imbalanced pre-tightening force during tensile tests. The effects of varying interference-fit and torque on pre-loaded transfer, surface strain distribution, tensile strength, and damage mode were identified. The results show that the synergy of interference-fit and torque induces an imbalanced pre-tightening force, which, in turn, changes the stress-strain evolution of the surface, and a special “transition regime” was identified in the evolution curves. Compared with clearance-fit, the ultimate strength and optimal torque of interference-fit joints could be significantly enhanced. In addition, the damage originates from fiber/matrix slipping to the upper surface with a low pre-tightening force and the formation of stack buckling, which then causes delamination fracture.
- 27 April 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (4)
Open AccessEffect of imbalanced interface pre-tightening force on the bearing behavior of carbon fiber reinforced polymer interference-fit lap joint
Interference-fit is attracting increasing attention in the aerospace field because of its excellent enhancement of the sealing and fatigue life of carbon fiber reinforced plastic (CFRP). However, it also induces imbalanced pre-tightening forces on the interface, and affects its mechanical behavior. A series of experiments were conducted to assess the imbalanced pre-tightening force of CFRP interference bolted joints and its effects. High-precision washer force sensors were used to measure the pre-tightening force between upper and lower surfaces at various interference-fit and torque. Strain gauges were used to estimate the varying effect on the imbalanced pre-tightening force during tensile tests. The effects of varying interference-fit and torque on pre-loaded transfer, surface strain distribution, tensile strength, and damage mode were identified. The results show that the synergy of interference-fit and torque induces an imbalanced pre-tightening force, which, in turn, changes the stress-strain evolution of the surface, and a special “transition regime” was identified in the evolution curves. Compared with clearance-fit, the ultimate strength and optimal torque of interference-fit joints could be significantly enhanced. In addition, the damage originates from fiber/matrix slipping to the upper surface with a low pre-tightening force and the formation of stack buckling, which then causes delamination fracture.