CÜCem Ünlübayir

Cem Ünlübayir

*This is an algorithmically generated author record based on publicly available information.

Cem Ünlübayir has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Coupled Transient Operation and Emission Analysis of a Natural Gas-Fueled SOFC-Battery Hybrid Demonstrator for Maritime Application

    by Marc P. Heddrich, Santiago Salas Ventura, Christian Schnegelberger, Jan Hollmann, Fabian Grimm, Johannes Rex, Joakim Pagels, Cem Ünlübayir, Alessandro Sissinio, Stefan Diethelm, et al.

    Introduction Recent demonstrations of commercial stationary natural gas-fed Solid Oxide Fuel Cell (SOFC) Systems have successfully demonstrated LHV to AC electrical efficiency values well above 60% [1,2]. This represents a highly attractive alternative to conventional Diesel- or LNG-fueled gensets of seagoing vessels, as the utilization of SOFC technology can both significantly reduce CO 2 emissions and almost entirely avoid combustion byproducts such as nitrogen oxides (NO x ), carbon monoxide (CO), particulate matter (PM) as well as methane slip. However, there are presently no such gensets demonstrated in a relevant power class and overall uncertainty regarding applicability, transient capability, genset sizing and emission reduction potential remains. The recently completed project Nautilus set its objective to close this research gap by developing and testing a novel maritime genset, consisting of LNG-fueled SOFC modules coupled with battery sets to enable reliable load-following while operating at overall high conversion efficiencies. Apart from marine component qualifications such as ship motion inclination testing of SOFC modules [3] and laboratory validation of energy management systems (EMS) [4], one of the core objectives of the Nautilus project consisted of a land-based demonstration of the proposed hybrid SOFC-battery genset to emulate ship-like operating conditions. This contribution aims to give an overview on the core demonstrator results, which include steady-state and transient testing of the SOFC module itself as well as battery-coupled operation in load-following mode of scaled-down real cruise ship profiles for both hotel and propulsive load. During all relevant operating conditions, CO 2 and non-CO 2 emissions of the SOFC module exhaust were measured and are compared to conventional genset data. Functional Demonstrator Layout The land-based demonstrator with a total rated power of 80 kW el,AC was commissioned on DLR premises in Stuttgart and is connected both to the local natural gas grid and the electricity grid. The arrangement and overall layout of the system is shown in Figure 1), depicting the (i) SOFC System, (ii) Battery, Controls and EMS and (iii) emission analysis subunits. The SOFC System with a rated electrical power of 60 kW el consists of a set of 40 G8 SolydEra stacks assembled in a system environment including anode off-gas recirculation with pre-reforming, air supply, fuel gas pre-cleaning, internal heat recuperation as well as a heat recovery unit for combined heat and power (CHP) application, the latter one not being used in the testing period shown here. The natural gas is provided by means of a compressor to ensure the required fuel supply pressure of 4 bar, which is meant to emulate the fuel supply on a ship after LNG evaporation. Thus, the compressor power is not accounted for in the efficiency calculation of the genset. In the second subunit, a marine certified 40 kWh Li-Ion battery along with a bidirectional DC-DC converter is installed. Both the battery and the DC output of the SOFC module are connected to a 600 V busbar, which feeds electrical power into the local 3-phase 400 V/50 Hz electricity grid by means of a frequency inverter and a transformer. From an external PC, the instantaneous power demand value, either set manually or coming from a timeseries of the cruise ship profiles, is fed to the EMS. Depending on the employed power distribution algorithm, the EMS sends power demands to the power electronics of SOFC and battery (charge/discharge) subsystems. The performance of EMS strategies was tested in a prior laboratory environment by coupling a single-pass multi-stack arrangement with a Li-Ion battery [4]. Finally, the exhaust emission analysis subunit consists of a Fourier transform infrared spectroscopy (FTIR) gas analyzer (ppm range), ppb range analyzers for NO x and SO 2 , as well as array particle monitors to measure several properties including particle number, mass concentration, and black carbon. Demonstrator Testing and Selected Results At the time of submission, the demonstrator has been operated for a total time of 1600 h and provided a total amount of electrical energy of 62.6 MWh. The testing campaign consisted of several distinct measurement tasks, which are briefly described: SOFC module steady-state electrical efficiencies along the load range , recorded in regular intervals throughout the testing campaign. Each operating point, defined by a constant electrical current, was held for 3 hours, while only the last 30 min were utilized to determine the steady-state performance. The corresponding LHV to AC electrical efficiency measurement points and a respective curve fit are depicted in Figure 2a) in red and are compared to a recently published field demonstration study by Gandiglio et al. [2] (blue). A peak efficiency of 63.4 % LHV to AC could be observed at 73 % of rated electrical power, with the characteristic drop towards lower part load operation. Both qualitatively and quantitatively, the obtained data is in close agreement with Gandiglio et al.. In addition, the potential thermal and combined CHP efficiency achievable with the built-in heat exchanger was estimated assuming exhaust recuperation down to 100°C, reaching values of up to 85 %. SOFC module load ramp tests to identify the transient performance without battery assist, at varying ramp rates (0.5, 2 and 4 % of rated module power per minute). The highest chosen ramp rate was given as a constraint from the SOFC system integrator due to balance of plant performance limitations. All load ramps tested on the demonstrator could be followed precisely (see Figure 2b) and without signs of negative impact of fuel and air supply dynamics on the stack, such as drops in stack voltage due to short-term fuel starvation, thus confirming the internal SOFC system control functionality for the depicted ramp tests. Higher ramp rates were tested in a dedicated SOFC single-pass lab test environment with identical stacks, exemplarily shown by a 10 %/min ramp as green line in Figure 2b). While downward ramps could be performed as intended, the upwards ramping capability was constrained due to minimum voltage constraints for cases where the stacks had remained at low part load for an extended period, resulting in lower stack temperatures. As longer time periods at low part load are to be expected in maritime applications, this characteristic represents a possible system constraint relevant for EMS design. CO 2 and non-CO 2 exhaust emissions along the steady-state load range and during transient operation . The non-CO 2 exhaust emissions, such as NO x and CO gas emissions, were found to vary substantially with load. Part load operation below 50% was particularly unfavorable, while 50% and above had low emission factors, especially for NO x . The emissions were not severely impacted by transient load changes other than that of the described effect from the load. The methane slip was practically negligible, with slightly increased emissions at very high load ramp rates. SOFC module continuous load ramp cycling between minimum and maximum permissible load at 4 % rated power per minute for a total repetition of 240 cycles, to stress the system and investigate if these operating regimes lead to degradation of the stacks. During and after completion of cycling, the steady state performance as described in (i) was repeated regularly, indicating that no relevant degradation could be observed, confirming that load ramps up to 4%/min are not significantly stressing the system. Performance during non-normal operation in a genset context , such as load rejection and black start capability. It could be demonstrated, that after a load rejection from the electrical grid, the SOFC module itself was able to switch into a safe electrically isolated hot standby mode at low electrical current by using the generated stack power to run the BoP consumers and electrically heating the inlet gases to sufficient temperatures, thus not requiring forming gas. It further could be shown that only the battery power was required to return the busbar to nominal voltage enabling resumption of energy flow to the grid, confirming the envisioned black start capability concept. Coupled SOFC-battery operation in load-following mode : Load profiles, deducted from real cruise ship power demands, including both propulsive and hotel load, were scaled to the demonstrator’s rated power to emulate the operation on a seagoing vessel under realistic conditions. Successful co-operation of battery and SOFC could be demonstrated, utilizing two rule-based power distribution strategies, investigated in prior laboratory tests [4]. For a given SOFC System load ramp rate of 2 %/min and cruise ship profiles, the required battery capacities were determined and recently published [5]. Conclusion By presenting these results in detail, the authors aim to provide a profound overview and reliable basis to the scientific community for designing and sizing hybrid SOFC battery gensets for MW-powertrain applications on seagoing vessels. Emission analysis has further confirmed the overall positive environmental impact of employing such systems to reduce the maritime carbon footprint. References Åström, K.; Hakala, T.; and Fontell, E. (2020), Product development and experiences of a new Convion SOFC system , Proceedings of the 14 th European SOFC & SOE Forum, A0602, 124-130. Gandiglio, M.; Marocco, P.; Nieminen, A.; Santarelli, M.; and Kiviaho, J. (2024). Energy and environmental performance from field operation of commercial-scale SOFC systems . International Journal of Hydrogen Energy, 85, 997–1009. https://doi.org/10.1016/j.ijhydene.2024.08.332 van Veldhuizen, B. N., Zera, E., van Biert, L., Modena, S., Visser, K., & Aravind, P. V. (2023). Experimental evaluation of a solid oxide fuel cell system exposed to inclinations and accelerations by ship motions . Journal of Power Sources, 585, 233634. https://doi.org/10.1016/j.jpowsour.2023.233634 Ünlübayir, C., Youssfi, H., Khan, R. A., Ventura, S. S., Fortunati, D., Rinner, J., Börner, M. F., Qaude, K. L., Ringbeck, F., and Sauer, D. U. (2024). Comparative analysis and test bench validation of energy management methods for a hybrid marine propulsion system powered by batteries and solid oxide fuel cells . Applied Energy, 376, 124183. https://doi.org/10.1016/j.apenergy.2024.124183 van Veldhuizen, B. N., van Biert, L., Ünlübayir, C., Visser, K., Hopman, J. J., & Aravind, P. V. (2025). Component sizing and dynamic simulation of a low-emission power plant for cruise ships with solid oxide fuel cells. Energy Conversion and Management, 326, 119477. https://doi.org/10.1016/j.enconman.2024.119477 Figure 1


  • Open Access

    Component sizing and dynamic simulation of a low-emission power plant for cruise ships with solid oxide fuel cells

    by B.N. van Veldhuizen, L. van Biert, C. Ünlübayir, K. Visser, J.J. Hopman, P.V. Aravind


  • Open Access

    A Data-Driven Approach to Ship Energy Management: Incorporating Automated Tracking System Data and Weather Information

    by Cem Ünlübayir, Ulrich Hermann Mierendorff, Martin Florian Börner, Katharina Lilith Quade, Alexander Blömeke, Florian Ringbeck, Dirk Uwe Sauer

    This research paper presents a data-based energy management method for a vessel that predicts the upcoming load demands based on data from weather information and its automated tracking system. The vessel is powered by a hybrid propulsion system consisting of a high-temperature fuel cell system to cover the base load and a battery system to compensate for the fuel cell’s limited dynamic response capability to load fluctuations. The developed energy management method predicts the load demand of the next time steps by analyzing physical relationships utilizing operational and positional data of a real vessel. This allows a steadier operation of the fuel cell and reduces stress factors leading to accelerated aging and increasing the resource efficiency of the propulsion system. Since large ships record tracking data of their cruise and no a priori training is required to adjust the energy management, the proposed method can be implemented with small additional computational effort. The functionality of the energy management method was verified using data from a real ship and records of the water currents in the North Sea. The accuracy of the load prediction is 2.7% and the attenuation of the fuel cell’s power output could be increased by approximately 32%.


  • Transient Solid Oxide Cell Reactor Model Used in rSOC Mode-Switching Analysis and Power Split Control of an SOFC-Battery Hybrid

    by Santiago Salas Ventura, Matthias Metten, Marius Tomberg, Dirk Ullmer, Cem Ünlübayir, Marc P. Heddrich, S. Asif Ansar

    Defossilization of the global energy system requires a transition towards intermittent renewable energy sources and approaches that enable efficient conversion of primary energy sources into electrical energy. Due to their high efficiency in converting chemical into electrical energy and vice versa, solid oxide cell (SOC) systems provide solutions for both of these aspects. Within this contribution, two researched cases utilizing SOC's are presented, based on simulation studies and experiments. Characteristically, SOC reactors produce hydrogen from steam in solid oxide electrolysis (SOE) mode, or electricity from reformates in solid oxide fuel cell (SOFC) mode. An application of both modes as reversible solid oxide cell (rSOC) is to balance a renewable power supply with storage and power production, leading to high utilization of the same equipment. An application in SOFC mode is the maritime transportation powertrain. In both cases, transient operation is needed whenever mode transitions occur. In particular, switching between rSOC modes implies transitioning exothermal SOFC, endothermal, thermoneutral and exothermal SOE operation. Similarly, supplying the power demand of a maritime drivetrain in SOFC mode leads to various exothermic levels, as pertinent to part or full load operation. Operating strategies are needed to suppress potentially damaging thermal stresses during these transitions in the electrochemical SOC reactors. In order to identify such operating strategies, experiments have been carried out and a transient model has been developed for the analysis of rSOC mode-switching and SOFC drivetrain power supply, which are presented in this study. The 1D+1D SOC dynamic multi-reactor model includes the individual SOC reactors, piping and insulation, and is implemented in the in-house developed transient energy process system simulation framework TEMPEST [1,2]. The model couples the transient balances of mass and energy with electrochemistry, internal reforming kinetics, heat transfer, and flow distribution. As a result, temperature and voltage characteristics at cell, stack, and module levels are obtained to analyze for e.g. unwanted thermal stress. In the EU project SWITCH [3], experiments were performed at DLR with a Large Stack Module (LSM) from SolydEra (formerly SOLIDpower) to validate the model in transient 75 kW electrolysis mode, 25 kW fuel cell mode and mode-switching operation between electrolysis and polygeneration mode. The so called polygeneration mode refers to simultaneous generation of hydrogen and electricity at partial fuel utilization with natural gas, biogas or e-methane. Simulative studies of mode-switching procedures from SOE to SOFC-mode polygeneration show that drawing fuel cell current soon after reaching open circuit voltage and sufficiently in advance of the methane ramp completion leads to a reduced temperature decrease at the inlet of the cell without reaching oxygen to carbon ratios low enough to favor carbon deposition. In the EU project NAUTILUS [4], the mismatch between the transient response possibilities of SOFC systems and the power demand of a ship is addressed by connecting Li-ion batteries to the powertrain. Batteries respond to highly transient ship load demand changes, while the SOFC’s provide base part load to full load, according to a power split control strategy. A battery model developed and parametrized by the Chair for Electrochemical Energy Conversion and Storage Systems of RWTH Aachen University [5] was added to TEMPEST and validated using DLR experiments with a 40 kWh Li-ion battery. Simulation results of the SOFC-battery hybrid in Figure 1 show that a rule-based power split control strategy [6] ensures that the power demand of the ship is met at all times while the battery state of charge (SoC) remains within specified range, and the SOFC power is drawn at one of three fixed power levels for reduced thermal stress. An experimental campaign to test this and other control strategies with a 32 kW LSM from SolydEra and the 40 kWh battery is in progress at DLR. Acknowledgements Project SWITCH has received funding from the Fuel Cells and Hydrogen 2 Joint Undertaking (now Clean Hydrogen Partnership) under Grant Agreement No 875148. This Joint Undertaking receives support from the European Union’s Horizon 2020 Research and Innovation program, Hydrogen Europe and Hydrogen Europe Research. Project NAUTILUS has received funding from the European Union’s Horizon 2020 research and innovation programme under grant agreement No 861647. References [1] S. Srikanth et al., Applied Energy 232 (2018) 473–488. DOI: 10.1016/j.apenergy.2018.09.186 [2] M. Tomberg et al., J. Electrochem. Soc. 2022, 169, 054530. DOI: 10.1149/1945-7111/ac7009 [3] SWITCH [Online, 16.12.2022] https://switch-fch.eu/ [4] NAUTILUS [Online, 16.12.2022] https://nautilus-project.eu/ [5] ISEA Framework [Online, 16.12.2022] https://git.rwth-aachen.de/isea/framework [6] Peng, H. et al. (2020). eTransportation, 4, 100057. DOI: 10.1016/j.etran.2020.100057 Figure 1. Transient simulation using an SOFC-battery power split algorithm and battery State of Charge (SoC). Figure 1

  • Transient Solid Oxide Cell Reactor Model Used in rSOC Mode-Switching Analysis and Power Split Control of an SOFC-Battery Hybrid

    by Santiago Salas Ventura, Matthias Metten, Marius Tomberg, Dirk Ullmer, Cem Ünlübayir, Marc P. Heddrich, S. Asif Ansar

    Defossilization of the global energy system requires a transition towards intermittent renewable energy sources and approaches that enable efficient conversion of primary energy sources into electrical energy. Due to their high efficiency in converting chemical into electrical energy and vice versa, solid oxide cell (SOC) systems provide solutions for both of these aspects. However, mode transitions in SOC operation require operating strategies to ensure that thermal gradients in the reactors are suppressed. In this study, two researched cases utilizing SOC’s are presented, based on simulation studies and experiments with an SOC multi-reactor module. The transient module model is validated in 75 kW electrolysis and polygeneration, and applied to analyze the effect of internal steam methane reforming on the temperature profile of the reactors. Subsequently, it is coupled with a validated Li-ion battery model, to test a rule-based power split control strategy suitable for a demand curve characteristic of a ship.


  • Cloud-based health-conscious energy management of hybrid battery systems in electric vehicles with deep reinforcement learning

    by Weihan Li, Han Cui, Thomas Nemeth, Jonathan Jansen, Cem Ünlübayir, Zhongbao Wei, Xuning Feng, Xuebing Han, Minggao Ouyang, Haifeng Dai, et al.