Ljubica Milović
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ljubica Milović has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Vujadin Aleksić
Institute for Materials Testing (IMS), 11000 Belgrade, Bulevar vojvode Mišića 43, Serbia
9 shared publications - Bojana Zečević
University of Belgrade, Innovation Centre of Faculty of Technology and Metallurgy, Karnegijeva 4, Belgrade, Serbia
8 shared publications - Ana Maksimović
Innovation Centre of the Faculty of Technology and Metallurgy, Belgrade, Serbia
6 shared publications - Srđan Bulatović
Institute for Materials Testing (IMS), 11000 Belgrade, Bulevar vojvode Mišića 43, Serbia
4 shared publications - Aleksandar Sedmak
University of Belgrade, Faculty of Mechanical Engineering, Belgrade, Serbia
3 shared publications - Mohammed Hadj Meliani
LPTPM, Hassiba Benbouali University of Chlef, Chlef, Algeria
3 shared publications
Latest Publications
- 12 October 2026
- Published by Institute of Metals and Technology in Materiali in tehnologije
- Vol. 60 (5)
METHODOLOGY FOR DETERMINING PLASTIC DEFORMATION BY PROCESSING DATA FROM LOW-CYCLE FATIGUE TESTS OF STEEL
The behavior of steel under low-cycle fatigue (LCF) was examined experimentally in accordance with the relevant standards. The stress-strain response under low-cycle fatigue takes the form of an idealized hysteresis loop. The strain range (Δε) corresponds to the total width of the loop, while the force (ΔF) or stress (Δσ) range corresponds to its total height. This paper presents a method for determining the intersection point of the idealized hysteresis loop with the positive part of the strain axis to determine the values of the elastic (Δεe/2) and plastic (Δεp/2) components of the strain half-amplitude to characterize steel behavior under low-cycle fatigue. The values of the elastic (Δεe/2) and plastic (Δεp/2) components of the strain half-amplitude are required to determine the characteristic low-cycle fatigue curves, namely the Cyclic Stress-Strain Curve (CSSC) and the Low-Cycle Fatigue Baseline Curve (LCFBC), which describe the behavior of steel under low-cycle fatigue conditions. The developed data-processing methodology for low-cycle fatigue (LCF) testing enables both the plastic and elastic components of the load to be determined at a given strain-amplitude level, in addition to defining the characteristic hysteresis loops.
- 12 October 2026
- Published by Institute of Metals and Technology in Materiali in tehnologije
- Vol. 60 (5)
METHODOLOGY FOR DETERMINING PLASTIC DEFORMATION BY PROCESSING DATA FROM LOW-CYCLE FATIGUE TESTS OF STEEL
The behavior of steel under low-cycle fatigue (LCF) was examined experimentally in accordance with the relevant standards. The stress-strain response under low-cycle fatigue takes the form of an idealized hysteresis loop. The strain range (Δε) corresponds to the total width of the loop, while the force (ΔF) or stress (Δσ) range corresponds to its total height. This paper presents a method for determining the intersection point of the idealized hysteresis loop with the positive part of the strain axis to determine the values of the elastic (Δεe/2) and plastic (Δεp/2) components of the strain half-amplitude to characterize steel behavior under low-cycle fatigue. The values of the elastic (Δεe/2) and plastic (Δεp/2) components of the strain half-amplitude are required to determine the characteristic low-cycle fatigue curves, namely the Cyclic Stress-Strain Curve (CSSC) and the Low-Cycle Fatigue Baseline Curve (LCFBC), which describe the behavior of steel under low-cycle fatigue conditions. The developed data-processing methodology for low-cycle fatigue (LCF) testing enables both the plastic and elastic components of the load to be determined at a given strain-amplitude level, in addition to defining the characteristic hysteresis loops.
- 1 May 2026
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 26 (1) , 3-7
Mechanical and metallographic properties of steel NIOMOL 490K SAW-joint
Bearing in mind the use of fine-grained micro alloyed steel NIOMOL 490K for welded structures exposed to impact loading at low temperatures, the mechanical and metallographic properties of its welded joint obtained by submerged arc welding (SAW), are examined. A filler metal, EPP 2NiMo2 Ø4 mm wire is used, in combination with OP 40 TT flux powder. The final aim of this research is to analyse the behaviour of welded joints under impact load at low temperatures in order to evaluate its fitness-to-service in real operating conditions.
- 1 May 2026
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 26 (1) , 3-7
Mechanical and metallographic properties of steel NIOMOL 490K SAW-joint
Bearing in mind the use of fine-grained micro alloyed steel NIOMOL 490K for welded structures exposed to impact loading at low temperatures, the mechanical and metallographic properties of its welded joint obtained by submerged arc welding (SAW), are examined. A filler metal, EPP 2NiMo2 Ø4 mm wire is used, in combination with OP 40 TT flux powder. The final aim of this research is to analyse the behaviour of welded joints under impact load at low temperatures in order to evaluate its fitness-to-service in real operating conditions.
- 1 May 2026
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 26 (1) , 192
Corrigendum - Numerical study of baffle parameters effect on field flow and power consumption
The current state of research in the field of stirred tanks across diverse industrial sectors places significant focus on the design of stirred tanks, turbine blades, and baffles. This research involves a numerical investigation which focuses on examining the velocity field in a tank subjected to mechanical agitation through a Rushton turbine, particularly in turbulent flow conditions. The study utilises a Newtonian fluid as the working medium and explores the influence of various factors, including the number and placement of baffles. The investigation employs a specialised calculation code called CFX 18.0. The numerical results are analysed to determine and discuss the impact of geometrical parameters, such as the number two, three and four shape, and spacing between vertical tubular baffles, on the power characteristics obtained for each impeller type.
- 1 May 2026
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 26 (1) , 192
Corrigendum - Numerical study of baffle parameters effect on field flow and power consumption
The current state of research in the field of stirred tanks across diverse industrial sectors places significant focus on the design of stirred tanks, turbine blades, and baffles. This research involves a numerical investigation which focuses on examining the velocity field in a tank subjected to mechanical agitation through a Rushton turbine, particularly in turbulent flow conditions. The study utilises a Newtonian fluid as the working medium and explores the influence of various factors, including the number and placement of baffles. The investigation employs a specialised calculation code called CFX 18.0. The numerical results are analysed to determine and discuss the impact of geometrical parameters, such as the number two, three and four shape, and spacing between vertical tubular baffles, on the power characteristics obtained for each impeller type.
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 340-345
A critical review on energy dissipator control strategies for structural vibration control
Passive control is one of the oldest systems of structure safety against dynamic loads. This strategy offers a structural protection using passive devices without needing any energy source or automation. Around the world, several of structures and tall buildings are equipped by these control devices. The passive control consists of a passive device superposed onto the main structure to improve the flexibility or damping. Therefore, during earthquake or wind excitation the additional devices absorb or reduce the caused shock and vibration of the structure. However, the literature is full of studies and investigations on the passive control application in the civil engineering area. Several of these investigations consider the effectiveness of energy dissipater devices to overcome structural disaster during earthquake loads. The main focus of the paper is to discuss the state-of-the-art of the passive control energy dissipater system. Different passive devices are described and the robustness in mitigating of earthquake structural vibration is discussed.
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 340-345
A critical review on energy dissipator control strategies for structural vibration control
Passive control is one of the oldest systems of structure safety against dynamic loads. This strategy offers a structural protection using passive devices without needing any energy source or automation. Around the world, several of structures and tall buildings are equipped by these control devices. The passive control consists of a passive device superposed onto the main structure to improve the flexibility or damping. Therefore, during earthquake or wind excitation the additional devices absorb or reduce the caused shock and vibration of the structure. However, the literature is full of studies and investigations on the passive control application in the civil engineering area. Several of these investigations consider the effectiveness of energy dissipater devices to overcome structural disaster during earthquake loads. The main focus of the paper is to discuss the state-of-the-art of the passive control energy dissipater system. Different passive devices are described and the robustness in mitigating of earthquake structural vibration is discussed.
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 329-335
Inspection by NDT-DT to analyse and control friction rotating welding of AISI 304L and AISI 316L stainless steel grade
The quality of the weld primarily depends on the parameters used during the welding process, including rotational speed, friction time and pressure, and forging time and pressure. Initially, welding operations are carried out on austenitic stainless steel bars, specifically from the AISI 304L and AISI 316L families, under a constant rotational speed. The first objective is to analyse the steel AISI 304L using the effect of two simultaneous parameters, namely two different forging times and two different forging pressures. The second objective is to evaluate the effect of five different friction phase times on AISI 316L, while keeping the other parameters constant, including friction pressure and forging pressure. Subsequently, a quality control is performed on all welded joints using non-destructive testing (NDT) techniques such as dye penetration testing, X-rays, and ultrasonics, in order to assess the impact of the aforementioned welding parameters on the quality of the joints. The results obtained indicate the presence of defects in some of the welded joints, estimated at 25 % in terms of joints, predominantly associated with low forging times or pressures.
- 30 November 2025
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 25 (2) , 329-335
Inspection by NDT-DT to analyse and control friction rotating welding of AISI 304L and AISI 316L stainless steel grade
The quality of the weld primarily depends on the parameters used during the welding process, including rotational speed, friction time and pressure, and forging time and pressure. Initially, welding operations are carried out on austenitic stainless steel bars, specifically from the AISI 304L and AISI 316L families, under a constant rotational speed. The first objective is to analyse the steel AISI 304L using the effect of two simultaneous parameters, namely two different forging times and two different forging pressures. The second objective is to evaluate the effect of five different friction phase times on AISI 316L, while keeping the other parameters constant, including friction pressure and forging pressure. Subsequently, a quality control is performed on all welded joints using non-destructive testing (NDT) techniques such as dye penetration testing, X-rays, and ultrasonics, in order to assess the impact of the aforementioned welding parameters on the quality of the joints. The results obtained indicate the presence of defects in some of the welded joints, estimated at 25 % in terms of joints, predominantly associated with low forging times or pressures.
- 24 December 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (3) , 407-413
Numerical study of baffle parameters effect on field flow and power consumption
The current state of research in the field of stirred tanks across diverse industrial sectors places significant focus on the design of stirred tanks, turbine blades, and baffles. This research involves a numerical investigation which focuses on examining the velocity field in a tank subjected to mechanical agitation through a Rushton turbine, particularly in turbulent flow conditions. The study utilises a Newtonian fluid as the working medium and explores the influence of various factors, including the number and placement of baffles. The investigation employs a specialised calculation code called CFX 18.0. The numerical results are analysed to determine and discuss the impact of geometrical parameters, such as the number two, three and four shape, and spacing between vertical tubular baffles, on the power characteristics obtained for each impeller type.
- 24 December 2024
- Published by Society for Structural Integrity and Life "Prof. dr Stojan Sedmak" in Structural Integrity and Life
- Vol. 24 (3) , 407-413
Numerical study of baffle parameters effect on field flow and power consumption
The current state of research in the field of stirred tanks across diverse industrial sectors places significant focus on the design of stirred tanks, turbine blades, and baffles. This research involves a numerical investigation which focuses on examining the velocity field in a tank subjected to mechanical agitation through a Rushton turbine, particularly in turbulent flow conditions. The study utilises a Newtonian fluid as the working medium and explores the influence of various factors, including the number and placement of baffles. The investigation employs a specialised calculation code called CFX 18.0. The numerical results are analysed to determine and discuss the impact of geometrical parameters, such as the number two, three and four shape, and spacing between vertical tubular baffles, on the power characteristics obtained for each impeller type.
- Open Access
Numerical Investigation of Fatigue Behavior in Ti-6Al-4V Orthopedic Hip Implants Subjected to Different Environments
In this paper, hip implants made of Ti-6Al-4V titanium alloy are analyzed numerically using Extended Finite Element Method XFEM. The combined effect of corrosion and fatigue was considered here since this is a common cause of failure of hip implants. Experimental testing of Ti-6Al-4V alloy was performed to determine its mechanical properties under different working environments, including normal, salty, and humid conditions. The integrity and life of the hip implant were assessed using the Linear Elastic Fracture Mechanics (LEFM) approach. For this purpose, the conditional fracture toughness Kq using CT specimens from all three groups (normal, humid, salty conditions) were determined. This provided insight into how different aggressive environments affect the behavior of Ti-6Al-4V alloy; i.e., how much its resistance to crack growth would degrade depending on conditions corresponding to the real exploitation of hip implants. Next, analytical and XFEM analyses of fatigue behavior in terms of the number of cycles were performed for all three groups, and the obtained results showed good agreement, confirming the validity of the integrity assessment approach shown in this work, which also represented a novel approach since fatigue and corrosion effects were investigated simultaneously.
Open AccessNumerical Investigation of Fatigue Behavior in Ti-6Al-4V Orthopedic Hip Implants Subjected to Different Environments
In this paper, hip implants made of Ti-6Al-4V titanium alloy are analyzed numerically using Extended Finite Element Method XFEM. The combined effect of corrosion and fatigue was considered here since this is a common cause of failure of hip implants. Experimental testing of Ti-6Al-4V alloy was performed to determine its mechanical properties under different working environments, including normal, salty, and humid conditions. The integrity and life of the hip implant were assessed using the Linear Elastic Fracture Mechanics (LEFM) approach. For this purpose, the conditional fracture toughness Kq using CT specimens from all three groups (normal, humid, salty conditions) were determined. This provided insight into how different aggressive environments affect the behavior of Ti-6Al-4V alloy; i.e., how much its resistance to crack growth would degrade depending on conditions corresponding to the real exploitation of hip implants. Next, analytical and XFEM analyses of fatigue behavior in terms of the number of cycles were performed for all three groups, and the obtained results showed good agreement, confirming the validity of the integrity assessment approach shown in this work, which also represented a novel approach since fatigue and corrosion effects were investigated simultaneously.
- 29 February 2024
- Published by Springer Nature
- p. 132-147
Corrosion Damages of Pipelines Assessment by Using the Finite Element Method
- 29 February 2024
- Published by Springer Nature
- p. 132-147
Corrosion Damages of Pipelines Assessment by Using the Finite Element Method
- Open Access
- 2 December 2023
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 48 (2) , 69-76
Numerical Determination of the Life of Steel Exposed To Low Cycle Fatigue
In the paper, based on the results of the experimental research of high-strength low-alloy steel (HSLA), Nionicral 70 (NN-70), under conditions of low-cycle fatigue (LCF), a numerical analysis of stress and determination of the life of steel samples was performed. Experimental testing of the behavior of the samples were performed with controlled and fully reversible strain (/2 = const, R = min/max = -1), according to the standard ISO 12106:2003 (E). For computational analyses, the following were used: the method of least squares and the method of finite elements (FEM). On the basis of the analysis of the results of the stress-deformation state and the determination of the life span through the isolines of the life span and comparison with the results of experimental tests, a graphic representation is given. The analysis justified the effort to numerically solve the estimation of the lifespan of steel under low cycle fatigue (LCF).
- 2 December 2023
- Published by Faculty of Technical Sciences in Advanced Technologies & Materials
- Vol. 48 (2) , 69-76
Open AccessNumerical Determination of the Life of Steel Exposed To Low Cycle Fatigue
In the paper, based on the results of the experimental research of high-strength low-alloy steel (HSLA), Nionicral 70 (NN-70), under conditions of low-cycle fatigue (LCF), a numerical analysis of stress and determination of the life of steel samples was performed. Experimental testing of the behavior of the samples were performed with controlled and fully reversible strain (/2 = const, R = min/max = -1), according to the standard ISO 12106:2003 (E). For computational analyses, the following were used: the method of least squares and the method of finite elements (FEM). On the basis of the analysis of the results of the stress-deformation state and the determination of the life span through the isolines of the life span and comparison with the results of experimental tests, a graphic representation is given. The analysis justified the effort to numerically solve the estimation of the lifespan of steel under low cycle fatigue (LCF).
- Open Access
- 15 February 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (1) , 148-152
Experimental Determination of the Critical Value of the J-Integral that Refers to the HSLA Steel Welded Joint
Fracture mechanics, as a scientific discipline dealing with the study of cracks in welded structures, has defined parameters and introduced new test methods in order to better determine the tendency to crack growth, critical conditions for rapid frac...
- 15 February 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (1) , 148-152
Open AccessExperimental Determination of the Critical Value of the J-Integral that Refers to the HSLA Steel Welded Joint
Fracture mechanics, as a scientific discipline dealing with the study of cracks in welded structures, has defined parameters and introduced new test methods in order to better determine the tendency to crack growth, critical conditions for rapid frac...