Bin Lu
Research Subjects
Research Interests
Bin Lu has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Xiaoying Zhang
Dimue Technologies Limited, Wuhan 430071, China
2 shared publications Aiqun Liu
Zhanjiang Branch of China National Offshore Oil Corporation Ltd., Zhanjiang 524057, China
1 shared publicationCaiwei Fan
Zhanjiang Branch of China National Offshore Oil Corporation Ltd., Zhanjiang 524057, China
1 shared publication- Changgui Xu
China Natl Off Shore Oil Ltd Corp, Beijing 101000, Peoples R China
1 shared publication - Chao Li
Sinopec Petroleum Exploration and Production Research Institute, Beijing 102206, China
1 shared publication Hu Li
Zhanjiang Branch of China National Offshore Oil Corporation Ltd., Zhanjiang 524057, China
1 shared publication
Latest Publications
- Open Access
Identification and Prediction of Allo-Source Overpressure Caused by Vertical Transfer: Example from an HTHP Gas Reservoir in the Ledong Slope in the Yinggehai Basin
The Yinggehai Basin is a typical high temperature and high pressure (HTHP) gas-bearing basin. The pressure coefficient exceeds 2.2 in deeply-buried Miocene reservoirs in the Ledong Slope, a nondiapir zone in the Yinggehai Basin. Determining the overpressure mechanisms and predicting the pore pressure are key issues for natural gas exploration and development in the Ledong Slope. In this paper, overpressure mechanisms were investigated according to the analysis of vertical effective stress-logging responses and geological evaluations, and the pore pressure was predicted using the Bowers method. The loading-unloading crossplots indicated that the overpressure that existed in reservoirs mainly consists of two types: neighbor-source and allo-source overpressure. The neighbor-source overpressure is mainly caused by the pressure transmission from the adjacent mudstone to the reservoir, with a pressure coefficient less than 1.51.6. The high-magnitude overpressure points with pressure coefficients greater than 1.6 show a typical unloading response, indicating elevated sandstone pressures rather than in situ mudstone pressures, which are most likely to be generated by overpressure vertical transfer. The high-magnitude overpressure fluid generated by the high mature ultradeep buried N1s source rock migrated to the shallower reservoirs via hidden faults/microfractures, which led to the vertical transfer of overpressure. Vertically transferred overpressure was generated at 1.50.2Ma, which is beneficial for the preservation of overpressure in lenticular sandbodies. The estimated pore pressure by the Bowers method is in good agreement with the measured pressure and provides a meaningful reference for predrilling pressure prediction in nondiapir or diapir zones in the Yinggehai Basin.
Open AccessIdentification and Prediction of Allo-Source Overpressure Caused by Vertical Transfer: Example from an HTHP Gas Reservoir in the Ledong Slope in the Yinggehai Basin
The Yinggehai Basin is a typical high temperature and high pressure (HTHP) gas-bearing basin. The pressure coefficient exceeds 2.2 in deeply-buried Miocene reservoirs in the Ledong Slope, a nondiapir zone in the Yinggehai Basin. Determining the overpressure mechanisms and predicting the pore pressure are key issues for natural gas exploration and development in the Ledong Slope. In this paper, overpressure mechanisms were investigated according to the analysis of vertical effective stress-logging responses and geological evaluations, and the pore pressure was predicted using the Bowers method. The loading-unloading crossplots indicated that the overpressure that existed in reservoirs mainly consists of two types: neighbor-source and allo-source overpressure. The neighbor-source overpressure is mainly caused by the pressure transmission from the adjacent mudstone to the reservoir, with a pressure coefficient less than 1.51.6. The high-magnitude overpressure points with pressure coefficients greater than 1.6 show a typical unloading response, indicating elevated sandstone pressures rather than in situ mudstone pressures, which are most likely to be generated by overpressure vertical transfer. The high-magnitude overpressure fluid generated by the high mature ultradeep buried N1s source rock migrated to the shallower reservoirs via hidden faults/microfractures, which led to the vertical transfer of overpressure. Vertically transferred overpressure was generated at 1.50.2Ma, which is beneficial for the preservation of overpressure in lenticular sandbodies. The estimated pore pressure by the Bowers method is in good agreement with the measured pressure and provides a meaningful reference for predrilling pressure prediction in nondiapir or diapir zones in the Yinggehai Basin.
- Open Access
Static Geological Modelling with Knowledge Driven Methodology
Geological modelling is an important topic of oil and gas exploration and production. A new knowledge driven methodology of geological modelling is proposed to address the problem of “hard data” limitation and modelling efficiency of the conventional data driven methodology. Accordingly, a new geological modelling software (DMatlas) (V1.0, Dimue, Wuhan, China) has been developed adopting a grid-free, object-based methodology. Conceptual facies models can be created for various depositional environments (such as fluvial, delta and carbonates). The models can be built largely based on geologists’ understandings with “soft data” such as outcrops analysis and geological maps from public literatures. Basic structures (fault, folds, and discrete fracture network) can be easily constructed according to their main features. In this methodology, models can be shared and re-used by other modelers or projects. Large number of model templates help to improve the modelling work efficiency. To demonstrate the tool, two case studies of geological modelling with knowledge driven methodology are introduced: (1) Suizhong 36-1 field which is a delta depositional environment in Bohai basin, China; (2) a site of the north Oman fracture system. The case studies show the efficiency and reliability within the new methodology.
Open AccessStatic Geological Modelling with Knowledge Driven Methodology
Geological modelling is an important topic of oil and gas exploration and production. A new knowledge driven methodology of geological modelling is proposed to address the problem of “hard data” limitation and modelling efficiency of the conventional data driven methodology. Accordingly, a new geological modelling software (DMatlas) (V1.0, Dimue, Wuhan, China) has been developed adopting a grid-free, object-based methodology. Conceptual facies models can be created for various depositional environments (such as fluvial, delta and carbonates). The models can be built largely based on geologists’ understandings with “soft data” such as outcrops analysis and geological maps from public literatures. Basic structures (fault, folds, and discrete fracture network) can be easily constructed according to their main features. In this methodology, models can be shared and re-used by other modelers or projects. Large number of model templates help to improve the modelling work efficiency. To demonstrate the tool, two case studies of geological modelling with knowledge driven methodology are introduced: (1) Suizhong 36-1 field which is a delta depositional environment in Bohai basin, China; (2) a site of the north Oman fracture system. The case studies show the efficiency and reliability within the new methodology.