Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yeşim Tarhan has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Phosphogypsum and Borogypsum as Additives for Sustainable and High-Performance 3D-Printable Concrete

    by Yeşim Tarhan, Berrin Atalay

    3D-printable concretes often require high binder content. This study evaluates the use of industrial gypsum by-products, phosphogypsum (PG) and borogypsum (BG), as partial cement replacements to enhance sustainability without compromising printability. PG and BG were incorporated at 2.5–10 wt% to replace the gypsum fraction in cement-based mortars containing fly ash (FA) or ground granulated blast-furnace slag (GGBS), with and without fibers. The fresh properties (spread flow diameter, open time, air content, density, and pH) and compressive strength were measured. At 28 days, the highest strength was achieved with a 7.5% PG addition to the GGBS system (~51 MPa), which exceeded the strength of the GGBS control C1 (~47.6 MPa). In the FA system, 2.5% PG reached 42.5 MPa, comparable to the FA control C2 (41.2 MPa). BG caused pronounced strength penalties at ≥7.5% across both binder systems, indicating a practical BG ceiling of ≤5%. Open time increased from ~0.75 h in the controls to ~2–2.5 h in BG-FA mixes with fibers, whereas PG mixes generally maintained a stable, printable window close to control levels. Overall, adding 5–7.5% PG, particularly in the presence of GGBS, improved mechanical performance without compromising workability. However, BG should be limited to ≤5% unless extended open time is the primary objective. These findings provide quantitative guidance on selecting PG/BG dosages and FA/GGBS systems to balance strength and printability in cement-based, 3D-printable concretes.


  • Open Access

    Nonlinear in-plane response of 3D-printed concrete walls with varied infill patterns: Experimental mix design and numerical structural assessment

    by İsmail Hakkı Tarhan, Yeşim Tarhan

    This study investigates the nonlinear in-plane structural behavior of 3D-printed concrete wall elements with two representative internal infill patterns ‒ lattice (L) and triangular (T) ‒ using finite element modeling informed by experimentally derived material properties. A printable concrete mixture was specifically developed using CEM I 42.5 R Portland cement, silica sand, and hydroxypropyl methylcellulose (HPMC) as a viscosity-modifying agent. Conventional cast specimens (40×40×160 mm³) achieved a 28-day flexural strength of 8.7 MPa and a compressive strength of approximately 63 MPa. Nonlinear behavior of wall panels with both infill types was investigated using numerical methods with advanced constitutive laws. These models account for the distinct compressive–tensile response of concrete and damage evolution under monotonic lateral loading, allowing assessment of the influence of geometry on load-bearing capacity and failure mechanisms. The results reveal that both infill patterns exhibit nonlinear load–displacement responses with an initial elastic regime, an early localized cracking peak, followed by a notable recovery in load-bearing capacity, and subsequently a global peak load prior to progressive post-peak softening. While the overall performance of both infill types was comparable, the T pattern exhibited a marginally higher peak load (1.7–2.7%) and improved ductility relative to the L form. These distinctions are attributed to the T-pattern’s more efficient diagonal force transfer and the development of a single continuous diagonal shear band, as opposed to the L-pattern’s multiple discontinuous cracks and broader damage zones.


  • Open Access

    Improving bond performance of 3D-printable earth-based mortar reinforced with jute fibers

    by Yeşim Tarhan, İsmail Hakkı Tarhan, Arnaud Perrot

    3D printing technology has transformed the construction industry by enabling rapid and cost-effective production of complex geometries. However, it faces significant challenges, including sustainability concerns due to cement's environmental impact and reinforcement issues arising from the incompatibility of traditional steel. These challenges necessitate the development of innovative material solutions. This study aims to enhance the bond strength between sustainable earth-based mortar and jute fibers used as reinforcement in 3D printed structures by exploring the effects of different treatments and compositions. Bond strength was evaluated by considering the effect of different treatments on the resistance of the fiber to being pulled out of the mortar. Pull-out tests were conducted on specimens with varying compositions and treatments. Results demonstrated substantial improvement in bond performance; specifically, the reference sand-free earth-clay mortar exhibited the lowest interfacial shear strength of 0.30 MPa. The most remarkable enhancement was observed in specimen which jute fibers pre-treated by immersion in mud slurry, which showed a 147% increase, reaching an interfacial shear strength of 0.74 MPa. Combining sand addition and fiber pre-treatment, however, did not yield additional benefits. These results indicate that simple, cost-effective local treatments can notably enhance fiber-matrix bond strength in 3D-printed earth-based structures without necessitating additional equipment or significant expense.


  • Open Access

    Investigation of Mechanical Properties and Microstructural Characteristics of Earth-Based Pavements Stabilised with Various Bio-Based Binders

    by Nuriye Kabakuş, Yeşim Tarhan

    For centuries, earthen materials have regained popularity because of the high carbon emissions caused by the construction sector. Although earth-based materials possess superior properties, such as recyclability, easy accessibility, affordability, and high thermal conductivity, they are not without drawbacks. They are, for instance, relatively weak and sensitive to water, and their physical and chemical properties can vary considerably depending on the source from which they are obtained. Stabilisation is often used to overcome these drawbacks. In this study, natural earth-based materials were stabilised with biopolymers of organic origin, such as alginate, Arabic gum, xanthan gum, and locust bean gum, to preserve their natural properties. To produce the samples, the earth material used in the road sub-base layer was mixed with kaolin clay and silica sand, and the mixtures were prepared by substituting biopolymer materials with clay at a ratio of 0.1%. After determining the fresh unit volume weights, spreading diameters (flow table test), penetration depths (fall cone test), and air content of the mixtures, the flexural and compressive strengths of the cured specimens were measured. In addition, scanning electron microscopy (SEM) and X-ray diffraction (XRD) analyses were performed to determine the microstructural characteristics. According to the 28-day compressive strength results, the mix with xanthan gum was found to be almost twice as strong as the other mixes. It has been concluded that biopolymer-stabilised earth mixtures can be used as a fill material in buildings where high strength is not required, or as a paving material on low-traffic roads.


  • CULTURAL HERITAGE CONSERVATION IN DIGITAL ERA: A REVIEW OF DIGITAL TWIN AND 3D PRINTING APPLICATIONS

    by İsmail Hakkı Tarhan, Yeşim Tarhan

    Digital Twin and 3D Printing technologies are advanced methods that integrate digital modeling, simulation, and automated fabrication and revolutionize various sectors. These technologies offer precise, efficient, and sustainable solutions, holding significant potential for enhancing preservation practices. Digital Twin technology enables the creation of detailed digital models, supporting real-time monitoring, predictive maintenance, and informed restoration planning. Meanwhile, 3D Printing allows the accurate reproduction of intricate architectural elements and artifacts, effectively bridging the gap between digital documentation and physical restoration. This review explores key research areas, including the replication of non-structural artifacts, structural rehabilitation, and material durability assessments. In total, 31 studies that included practical applications relevant to this study's scope were reviewed. Despite their numerous benefits, challenges such as high costs, specialized technical skills, and ethical considerations in heritage preservation remain. The study also anticipates future advancements, such as integrating smart materials, augmented reality, and robotics for autonomous restoration. This study provides insights into how Digital Twin and 3D Printing technologies can promote more effective, sustainable conservation practices in the digital age by evaluating current applications and challenges.


  • Physical Properties of Earth-Based Materials Stabilised with Biopolymer Binder

    by Nuriye Kabakuş, Yeşim Tarhan, Flavio Craveiro, Helena Bartolo

  • Open Access

    Comprehensive Review of Binder Matrices in 3D Printing Construction: Rheological Perspectives

    by Yeşim Tarhan, İsmail Hakkı Tarhan, Remzi Şahin

    Three-dimensional printing technology is transforming the construction industry, which is increasingly turning to advanced materials and techniques to meet environmental and economic challenges. This comprehensive literature review evaluated various binder materials, including cement, geopolymers, earthen materials, supplementary cementitious materials, polymers, and biopolymers, with a focus on their environmental impacts and rheological properties. The study revealed an increasing interest in cementitious binders, which deliver essential structural strength and exhibit a wide range of yield stress values (15 to 6500 Pa), influenced by binder type and supplementary materials such as nanoclay. However, the significant CO2 emissions associated with cement pose major sustainability challenges. As a sustainable alternative, geopolymers demonstrate lower yield stress values (800 to 3000 Pa) while ensuring adequate buildability for vertical printing and reducing environmental impact. These findings underscore the need to adopt sustainable binder matrices to align 3D printing construction practices with global sustainability goals.


  • Open Access

    Enhancing Sustainable Road Construction: Evaluation of the Mechanical and Durability Properties of Stabilized Earth-Based Pavement Materials

    by Yeşim Tarhan, Nuriye Kabakuş

    The materials traditionally used in the construction of flexible and rigid pavements in modern road infrastructure present challenges in achieving sustainable development goals. Advances in technology have introduced the use of different pavement material mixes, leading to the introduction of earth-based alternatives. These materials are environmentally friendly, cost-effective, recyclable, and offer excellent insulation properties. Stabilization of earth-based materials improves their mechanical properties, reducing road construction costs and increasing durability. The present study investigates the mechanical and durability properties of earth-based materials stabilized with various additives, including cement, lime, polymer, and biopolymer, over 28 and 56 days. Fresh properties are assessed using unit volume weight, flow table, air content, and fall cone tests, while hardened properties are assessed using flexural strength, compressive strength, and water absorption. Microstructural analysis is carried out using scanning electron microscopy (SEM) and X-ray diffraction (XRD). The cement-stabilized samples show improved strength and durability, with the 5% cement group showing a 67% increase in compressive strength over the control group and the 10% cement group showing over 200% higher compressive strength. These results suggest that stabilized earth-based materials could provide a cost-effective and sustainable alternative to conventional pavements for low-traffic roads.