Chenjie Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Chenjie Lin has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Amir Ranjbar
University of Texas at Dallas
1 shared publication- Ashfanoor Kabir
Corporate Research, ABB, United States
1 shared publication Babak Fahimi
University of Texas at Dallas
1 shared publication- Federico Bertoldi
Corporate Research, ABB, 18922 Sweden
1 shared publication Joseph David Hearron
University of Texas at Dallas
1 shared publication- Matthew M. McDonough
Department of Orthopaedics and Rehabilitation, Womack Army Medical Center , Fort Bragg, NC 28310
1 shared publication
Latest Publications
- 15 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (8) , 6584-6594
Self-Excited Synchronous Machine Using Airgap Harmonics
This paper introduces a self-excitation technology for Field Wound Synchronous Machines (FWSM) to eliminate conventional components required by brushless and brushed static excitation systems. This technology is based on the utilization of pre-existing airgap flux harmonics, so no exciter or brush is required. The energy of these airgap harmonics at the slotting frequency is captured using rotor-mounted harvesting coils. A power electronic converter is then used to rectify the induced harvesting coil voltage and regulate the field winding current of the FWSM. Simulation results are presented showing the efficacy of the proposed method for a prototype FWSM under various loading conditions. For demonstration, a full scale 5.4MVA synchronous generator is used for design and validation.
- 15 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industrial Electronics
- Vol. 68 (8) , 6584-6594
Self-Excited Synchronous Machine Using Airgap Harmonics
This paper introduces a self-excitation technology for Field Wound Synchronous Machines (FWSM) to eliminate conventional components required by brushless and brushed static excitation systems. This technology is based on the utilization of pre-existing airgap flux harmonics, so no exciter or brush is required. The energy of these airgap harmonics at the slotting frequency is captured using rotor-mounted harvesting coils. A power electronic converter is then used to rectify the induced harvesting coil voltage and regulate the field winding current of the FWSM. Simulation results are presented showing the efficacy of the proposed method for a prototype FWSM under various loading conditions. For demonstration, a full scale 5.4MVA synchronous generator is used for design and validation.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19388756,p. 1-6
The sustainability of new technologies in vehicular transportation
This paper compares the sustainability of three new technologies in vehicular transportation which consist of (1) innovations in the fuel the vehicles use and (2) innovations in the vehicle design itself. An array of vehicle platforms, which consist of different vehicle designs and fuels types, are modeled and a life cycle analysis (LCA) is performed to find the total energy consumption and emissions of each model. As high energy consumption and pollution become growing concerns, this paper aims to provide a better understanding of where new advancements in vehicular technology should be focused.
- 1 September 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 19388756,p. 1-6
The sustainability of new technologies in vehicular transportation
This paper compares the sustainability of three new technologies in vehicular transportation which consist of (1) innovations in the fuel the vehicles use and (2) innovations in the vehicle design itself. An array of vehicle platforms, which consist of different vehicle designs and fuels types, are modeled and a life cycle analysis (LCA) is performed to find the total energy consumption and emissions of each model. As high energy consumption and pollution become growing concerns, this paper aims to provide a better understanding of where new advancements in vehicular technology should be focused.