Xing’an Liu

With the rapid development of vertical takeoff and landing (VTOL) aircraft, the blade design of a propeller suitable for VTOL aircraft with a wide range of operating conditions has become a challenging and popular task. This paper proposes a multi-objective optimization framework for a VTOL propeller using an inverse design method at the cruising stage, which is developed from the Betz optimum theory and blade element momentum theory (BEMT). Different from passing studies, the maximum thrust-to-weight ratio at hover (MTWRH) is taken as one of the two objectives in this paper, which is closely related to the wind-resistance capability and maneuverability during takeoff and landing. The other objective is the energy consumption of the whole mission profile. A fixed pitch propeller (FPP) and a variable pitch propeller (VPP) are both optimized using the proposed framework for the Vahana A³ tilt-wing aircraft and validated by the computational fluid dynamics (CFD) method. The influences of the level flight energy ratio, hover disk loading and cruising speed toward the optimization result are analyzed, respectively. The results show that the MTWRH has a significant impact on the optimization result both for the FPP and VPP. A comparison between the two propeller forms validates the advantages of the VPP both in energy saving and takeoff maneuverability. The quantitative rules of this advantage with the level flight energy ratio are calculated to provide a reference for choosing the appropriate form. Overall, the methodology and general rules presented in this paper support the propeller optimization and form selection for VTOL aircraft.

In this study, a modified Block A* algorithm is applied to the path planning of hybrid-driven underwater gliders, which combine the buoyancy-driven mode of underwater gliders and the propeller-driven mode of autonomous underwater vehicles, in the ocean environment characterized by strong currents. The objective is to predict a sequence of steering directions and the appropriate driving mode, such that vehicles can minimize their energy consumption to reach the goal region. In this work, we modify the path generation approach of the original Block A* algorithm to gain more realistic paths for hybrid-driven underwater gliders and apply an effective energy consumption model in the heap value calculation to find energy-cost optimal paths. Zermelo's function is also incorporated to select the driving mode. The performance of the presented method is then discussed by conducting simulations in three different ocean environments. The results indicate that compared to other methods, the modified Block A* method avoids local turbulent flow and gains feasible paths for hybrid-driven underwater gliders at a lower energy cost.

Nowadays, with the escalating tensions in maritime dispute and the development of marine economy, there has been renewed interest in seaplanes for their special capacity of taking off and landing on water. Prediction of take-off performance, involving aerodynamic analysis and hydrodynamic analysis, is a main challenge in seaplane design, while the prediction methods have been little improved since the 1960s. This paper aims to investigate the attitude and resistance characteristics of a seaplane at different speeds during the take-off by numerically modeling the air-water flow field using RANS equations with VOF method. The trim and heave motion of seaplane in response to aerodynamic forces, hydrodynamic forces, hydrostatic forces, and propeller thrust was realized by solving rigid body dynamics equations and adopting dynamic overset mesh technique. The variations in heave, trim angle, and resistance characteristics during the takeoff were investigated, and their inherent relationships with the aerodynamic, hydrodynamic, and hydrostatic performance were revealed. Particular investigation on the hydrodynamic resistance indicates that the stagnation line located at the convex bow would contribute a considerable increase of pressure resistance at the first hump, and the trim angel of a seaplane should be operated in an optimum trim range, typical between 4–6 deg, to minimize the hydrodynamic resistance at the second hump. Additionally, the dynamic motion convergence study proves that the utilization of damping terms was an effective way to accelerate the convergence of the dynamic motion ending with a quasi-static state.

Wing–in–ground crafts will face waves with different amplitudes when flying over the ocean, and the high amplitude situations are especially lack of exploration. Hence, the aerodynamic characteristics of the NACA 4412 airfoil in proximity to the wavy water surface for various wave amplitudes are inspected in this paper. By solving Navier–Stokes equations, the lift coefficients of the airfoil when the angle of attack ranges from 0° to 4° are obtained. The results show that the fluctuation amplitudes of aerodynamic coefficients increase remarkably with successive increases in the wave amplitude and might threaten flight safety. The flow fields at 0° with low and high wave amplitudes are investigated. It is revealed that the upward movement of the water surface is the critical factor for the change of aerodynamics, and the mechanism varies with different wave amplitudes. Comparison of the flow fields at 0° and 2° further indicates that the influence of high amplitude waves depends on the distance between the leading edge of the airfoil and the water surface. This study discovers the reasons for the different aerodynamic characteristics under various wave amplitudes and angles of attack, and is of great value for the design of wing–in–ground crafts.