Paulette Antoinette Loichet Torres
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Paulette Antoinette Loichet Torres has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Hubert Andreas Gasteiger
Technical University of Munich
2 shared publications - Peter Fischer
Applied Electrochemistry, Fraunhofer Institute for Chemical Technology ICT, Joseph-von-Fraunhofer Straße 7, 76327 Pfinztal, Germany
2 shared publications Christian H. Liebscher
Max-Planck-Institut für Eisenforschung GmbH, Max-Planck-Straße 1, D-40237 Düsseldorf, Germany
1 shared publicationCorbinian Grön
Chair of Technical Electrochemistry, Department of Chemistry and Catalysis Research Center, School of Natural Sciences, Technical University of Munich, D-85748 Garching, Germany
1 shared publicationDavide Menga
1 shared publicationEmeline Meyer
Applied Electrochemistry Fraunhofer Institute for Chemical Technology ICT Joseph-von-Fraunhofer Straße 7 76327 Pfinztal Germany
1 shared publication
Latest Publications
- Open Access
- 1 December 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (12) , 124503
ORR Activity and Voltage-Cycling Stability of a Carbon-Supported PtxY Alloy Catalyst Evaluated in a PEM Fuel Cell
Platinum-yttrium alloys (PtxY) are suggested to have superior oxygen reduction reaction (ORR) activity and long-term stability in proton exchange membrane fuel cells (PEMFCs). However, the actual ORR activity and stability of a PtxY catalyst with a high electrochemically active surface area (ECSA) in a PEMFC remains uncertain. Here, a Ketjen black (KB) carbon supported PtxY/KB catalyst with a high ECSA (∼60 m2/g) was synthesized using a carbon nitride precursor. Based on elemental analysis, XRD, electron microscopy, and a mass-balance based model, it was shown that the acid-leached PtxY nanoparticles of the catalyst consist of a ∼0.7 nm thick Pt-shell and a Pt3Y core. Rotating disk electrode (RDE) and 5 cm2 single-cell PEMFC measurements indicated that the ORR activity of the acid-leached PtxY/KB catalyst is similar to an analogously synthesized Pt/KB reference catalyst with the same ECSA. Voltage-cycling accelerated stress tests (ASTs) between 0.6−1.0 V (in H2/N2 at 80 °C/95% RH) in 5 cm2 single-cells showed that the ORR activity and durability of the PtxY/KB catalyst is similar to that of the Pt/KB reference catalyst. Thus, the high durability of Pt-rare Earth alloys that has been claimed on the basis of RDE measurements is not observed in actual PEMFCs.
- 1 December 2023
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 170 (12) , 124503
Open AccessORR Activity and Voltage-Cycling Stability of a Carbon-Supported PtxY Alloy Catalyst Evaluated in a PEM Fuel Cell
Platinum-yttrium alloys (PtxY) are suggested to have superior oxygen reduction reaction (ORR) activity and long-term stability in proton exchange membrane fuel cells (PEMFCs). However, the actual ORR activity and stability of a PtxY catalyst with a high electrochemically active surface area (ECSA) in a PEMFC remains uncertain. Here, a Ketjen black (KB) carbon supported PtxY/KB catalyst with a high ECSA (∼60 m2/g) was synthesized using a carbon nitride precursor. Based on elemental analysis, XRD, electron microscopy, and a mass-balance based model, it was shown that the acid-leached PtxY nanoparticles of the catalyst consist of a ∼0.7 nm thick Pt-shell and a Pt3Y core. Rotating disk electrode (RDE) and 5 cm2 single-cell PEMFC measurements indicated that the ORR activity of the acid-leached PtxY/KB catalyst is similar to an analogously synthesized Pt/KB reference catalyst with the same ECSA. Voltage-cycling accelerated stress tests (ASTs) between 0.6−1.0 V (in H2/N2 at 80 °C/95% RH) in 5 cm2 single-cells showed that the ORR activity and durability of the PtxY/KB catalyst is similar to that of the Pt/KB reference catalyst. Thus, the high durability of Pt-rare Earth alloys that has been claimed on the basis of RDE measurements is not observed in actual PEMFCs.
- Open Access
- 18 February 2022
- Published by Wiley in Chemistry – A European Journal
- Vol. 28 (13) , e202103491
Properties of Bromine Fused Salts Based on Quaternary Ammonium Molecules and Their Relevance for Use in a Hydrogen Bromine Redox Flow Battery
Bromine complexing agents (BCA) in aqueous electrolytes for hydrogen bromine flow batteries are used to reduce bromine‘s vapour pressure, while an insoluble and liquid fused salt is formed. The properties (concentrations, composition, conductivity and viscosity) of this fused salt are investigated in this study systematically ex situ by using 7 BCAs at different state of charge in HBr/Br2/H2O electrolytes with a theoretical capacity of 179.6 Ah L−1. Bromine is stored in the fused salt at concentrations up to 13.6 M, reaching theoretical volumetrical capacities up to 730 Ah L−1 in fused salts. The fused salt consists of a pure, bromine‐ and water‐free ionic liquid of organic [BCA]+ cations and polybromides, and its conductivity bases on a hopping mechanism among the polybromides. Alkyl side chain length of the BCAs and distribution of polybromides influence strongly the conductivity and viscosity of the fused salts. 1‐ethylpyridin‐1‐iumbromide results to be favoured BCA for application.
- 18 February 2022
- Published by Wiley in Chemistry – A European Journal
- Vol. 28 (13) , e202103491
Open AccessProperties of Bromine Fused Salts Based on Quaternary Ammonium Molecules and Their Relevance for Use in a Hydrogen Bromine Redox Flow Battery
Bromine complexing agents (BCA) in aqueous electrolytes for hydrogen bromine flow batteries are used to reduce bromine‘s vapour pressure, while an insoluble and liquid fused salt is formed. The properties (concentrations, composition, conductivity and viscosity) of this fused salt are investigated in this study systematically ex situ by using 7 BCAs at different state of charge in HBr/Br2/H2O electrolytes with a theoretical capacity of 179.6 Ah L−1. Bromine is stored in the fused salt at concentrations up to 13.6 M, reaching theoretical volumetrical capacities up to 730 Ah L−1 in fused salts. The fused salt consists of a pure, bromine‐ and water‐free ionic liquid of organic [BCA]+ cations and polybromides, and its conductivity bases on a hopping mechanism among the polybromides. Alkyl side chain length of the BCAs and distribution of polybromides influence strongly the conductivity and viscosity of the fused salts. 1‐ethylpyridin‐1‐iumbromide results to be favoured BCA for application.
- Open Access
- 1 July 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (7) , 070554
Impact of Plasma and Thermal Treatment on the Long-term Performance of Vanadium Redox Flow Electrodes – Significance of Surface Structure vs Oxygen Functionalities
Graphite felt (GF) electrodes of vanadium redox flow batteries show enhanced performance when thermally treated before their assembly. Thermal treatment works by simultaneously increasing electrode wettability, kinetic activity, and total surface area (TSA). This study examines these performance determining yet inseparable effects, especially considering the electrodes’ long-term operation. We exposed GF electrodes to 5 min plasma treatment, ensuring equal wettability, and thermally treated them in air at 400 °C for different durations. We then linked the resulting GF surface structure with the electrode performance, monitored with a high temporal resolution, and controlled electrolyte conditions. The performance, expressed in charge-transfer resistances and voltage efficiencies, correlated accurately with the thermal treatment times. According to XPS, against expectation, the thermal treatment decreased the number of surface oxygen functionalities. Instead, SEM and krypton adsorption revealed that the surface had become rougher, and the TSA increased. Upon corrosion, the surface presumably exposed more carbon edge sites being catalytically active, explaining the improved performance. Therefore, compared with the commonly suggested surface oxygen enrichment, increasing the GF surface roughness and TSA may be the more promising strategy to enhance and stabilize the long-term VRF electrode performance.
- 1 July 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (7) , 070554
Open AccessImpact of Plasma and Thermal Treatment on the Long-term Performance of Vanadium Redox Flow Electrodes – Significance of Surface Structure vs Oxygen Functionalities
Graphite felt (GF) electrodes of vanadium redox flow batteries show enhanced performance when thermally treated before their assembly. Thermal treatment works by simultaneously increasing electrode wettability, kinetic activity, and total surface area (TSA). This study examines these performance determining yet inseparable effects, especially considering the electrodes’ long-term operation. We exposed GF electrodes to 5 min plasma treatment, ensuring equal wettability, and thermally treated them in air at 400 °C for different durations. We then linked the resulting GF surface structure with the electrode performance, monitored with a high temporal resolution, and controlled electrolyte conditions. The performance, expressed in charge-transfer resistances and voltage efficiencies, correlated accurately with the thermal treatment times. According to XPS, against expectation, the thermal treatment decreased the number of surface oxygen functionalities. Instead, SEM and krypton adsorption revealed that the surface had become rougher, and the TSA increased. Upon corrosion, the surface presumably exposed more carbon edge sites being catalytically active, explaining the improved performance. Therefore, compared with the commonly suggested surface oxygen enrichment, increasing the GF surface roughness and TSA may be the more promising strategy to enhance and stabilize the long-term VRF electrode performance.
- Open Access
Systematic Study of Quaternary Ammonium Cations for Bromine Sequestering Application in High Energy Density Electrolytes for Hydrogen Bromine Redox Flow Batteries
Bromine complexing agents (BCAs) are used to reduce the vapor pressure of bromine in the aqueous electrolytes of bromine flow batteries. BCAs bind hazardous, volatile bromine by forming a second, heavy liquid fused salt. The properties of BCAs in a strongly acidic bromine electrolyte are largely unexplored. A total of 38 different quaternary ammonium halides are investigated ex situ regarding their properties and applicability in bromine electrolytes as BCAs. The focus is on the development of safe and performant HBr/Br2/H2O electrolytes with a theoretical capacity of 180 Ah L−1 for hydrogen bromine redox flow batteries (H2/Br2-RFB). Stable liquid fused salts, moderate bromine complexation, large conductivities and large redox potentials in the aqueous phase of the electrolytes are investigated in order to determine the most applicable BCA for this kind of electrolyte. A detailed study on the properties of BCA cations in these parameters is provided for the first time, as well as for electrolyte mixtures at different states of charge of the electrolyte. 1-ethylpyridin-1-ium bromide [C2Py]Br is selected from 38 BCAs based on its properties as a BCA that should be focused on for application in electrolytes for H2/Br2-RFB in the future.
Open AccessSystematic Study of Quaternary Ammonium Cations for Bromine Sequestering Application in High Energy Density Electrolytes for Hydrogen Bromine Redox Flow Batteries
Bromine complexing agents (BCAs) are used to reduce the vapor pressure of bromine in the aqueous electrolytes of bromine flow batteries. BCAs bind hazardous, volatile bromine by forming a second, heavy liquid fused salt. The properties of BCAs in a strongly acidic bromine electrolyte are largely unexplored. A total of 38 different quaternary ammonium halides are investigated ex situ regarding their properties and applicability in bromine electrolytes as BCAs. The focus is on the development of safe and performant HBr/Br2/H2O electrolytes with a theoretical capacity of 180 Ah L−1 for hydrogen bromine redox flow batteries (H2/Br2-RFB). Stable liquid fused salts, moderate bromine complexation, large conductivities and large redox potentials in the aqueous phase of the electrolytes are investigated in order to determine the most applicable BCA for this kind of electrolyte. A detailed study on the properties of BCA cations in these parameters is provided for the first time, as well as for electrolyte mixtures at different states of charge of the electrolyte. 1-ethylpyridin-1-ium bromide [C2Py]Br is selected from 38 BCAs based on its properties as a BCA that should be focused on for application in electrolytes for H2/Br2-RFB in the future.
- Open Access
- 1 May 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (5) , 052508
Hydrogen Gas Promoted Self-Limiting Copper Monolayer Deposition on Platinum
A hydrogen gas promoted approach to achieve copper underpotential deposition (UPD) on platinum surfaces was developed to form a copper monolayer on polycrystalline platinum and carbon supported platinum catalysts (Pt/C) in a Cu2+-containing electrolyte, serving as alternative to the commonly used electrochemical deposition methods that require external potential control. Initially, the amount of deposited copper in the presence of dissolved hydrogen was determined via fast stripping voltammetry. Subsequently, by monitoring the open circuit potential drop of Pt disk and Pt/C thin-film electrodes upon exposure of an air saturated electrolyte to H2 containing gas, it could be shown that self-limiting Cu coverages of essentially one monolayer can reliably be obtained for 0.1% and 3% H2/Ar mixtures. In a second part, a cell was designed aiming to facilitate the gram-scale preparation of CuUPDPt/C catalysts by the H2 gas promoted approach. The formation of a Cu UPD layer on the Pt nanoparticles supported on carbon with a coverage slightly higher than a monolayer was successfully validated. However, the reaction cell introduced non-idealities at the solution/gas interface, which would need to be optimized to achieve a perfectly self-limiting Cu monolayer on the Pt nanoparticles by the H2 promoted deposition.
- 1 May 2021
- Published by The Electrochemical Society in Journal of the Electrochemical Society
- Vol. 168 (5) , 052508
Open AccessHydrogen Gas Promoted Self-Limiting Copper Monolayer Deposition on Platinum
A hydrogen gas promoted approach to achieve copper underpotential deposition (UPD) on platinum surfaces was developed to form a copper monolayer on polycrystalline platinum and carbon supported platinum catalysts (Pt/C) in a Cu2+-containing electrolyte, serving as alternative to the commonly used electrochemical deposition methods that require external potential control. Initially, the amount of deposited copper in the presence of dissolved hydrogen was determined via fast stripping voltammetry. Subsequently, by monitoring the open circuit potential drop of Pt disk and Pt/C thin-film electrodes upon exposure of an air saturated electrolyte to H2 containing gas, it could be shown that self-limiting Cu coverages of essentially one monolayer can reliably be obtained for 0.1% and 3% H2/Ar mixtures. In a second part, a cell was designed aiming to facilitate the gram-scale preparation of CuUPDPt/C catalysts by the H2 gas promoted approach. The formation of a Cu UPD layer on the Pt nanoparticles supported on carbon with a coverage slightly higher than a monolayer was successfully validated. However, the reaction cell introduced non-idealities at the solution/gas interface, which would need to be optimized to achieve a perfectly self-limiting Cu monolayer on the Pt nanoparticles by the H2 promoted deposition.