Siyu Yang

With the utilization of advanced microfluidic techniques, the microfluidic particle counter demonstrates significant potential due to its high efficiency, precise manipulation, and portability. This work focuses on a photodetection counter based on optical absorption. To achieve precise particle detection, a Christmas tree-like structure was implemented to separate a single particle from a cluster, which was then detected in independent multiple parallel channels. The system exhibits a high degree of reliability, as evidenced by a linear correlation coefficient over 0.99 obtained during testing with gradient-concentrated beads. Furthermore, when the calculated density of NIH 3T3 cells is compared with that of a traditional flow cytometer, the system achieves a substantial agreement percentage ranging from 87.5 to 99.9%. The system’s ability to perform high-throughput analysis with a high acquisition rate positions it as a promising tool for real-time point-of-care testing.

Polydimethylsiloxane (PDMS) has been widely used to make lab-on-a-chip devices, such as reactors and sensors, for biological research. Real-time nucleic acid testing is one of the main applications of PDMS microfluidic chips due to their high biocompatibility and transparency. However, the inherent hydrophobicity and excessive gas permeability of PDMS hinder its applications in many fields. This study developed a silicon-based polydimethylsiloxane-polyethylene-glycol (PDMS-PEG) copolymer microfluidic chip, the PDMS-PEG copolymer silicon chip (PPc-Si chip), for biomolecular diagnosis. By adjusting the modifier formula for PDMS, the hydrophilic switch occurred within 15 s after contact with water, resulting in only a 0.8% reduction in transmittance after modification. In addition, we evaluated the transmittance at a wide range of wavelengths from 200 nm to 1000 nm to provide a reference for its optical property study and application in optical-related devices. The improved hydrophilicity was achieved by introducing a large number of hydroxyl groups, which also resulted in excellent bonding strength of PPc-Si chips. The bonding condition was easy to achieve and time-saving. Real-time PCR tests were successfully conducted with higher efficiency and lower non-specific absorption. This chip has a high potential for a wide range of applications in point-of-care tests (POCT) and rapid disease diagnosis.

Real-time polymerase chain reaction (real-time PCR) tests were successfully conducted in an aluminum-based microfluidic chip developed in this work. The reaction chamber was coated with silicone-modified epoxy resin to isolate the reaction system from metal surfaces, preventing the metal ions from interfering with the reaction process. The patterned aluminum substrate was bonded with a hydroxylated glass mask using silicone sealant at room temperature. The effect of thermal expansion was counteracted by the elasticity of cured silicone. With the heating process closely monitored, real-time PCR testing in reaction chambers proceeded smoothly, and the results show similar quantification cycle values to those of traditional test sets. Scanning electron microscope (SEM) and atomic force microscopy (AFM) images showed that the surface of the reaction chamber was smoothly coated, illustrating the promising coating and isolating properties. Energy-dispersive X-ray spectroscopy (EDS), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma-optical emission spectrometer (ICP-OES) showed that no metal ions escaped from the metal to the chip surface. Fourier-transform infrared spectroscopy (FTIR) was used to check the surface chemical state before and after tests, and the unchanged infrared absorption peaks indicated the unreacted, antifouling surface. The limit of detection (LOD) of at least two copies can be obtained in this chip.

Real-time polymerase chain reaction (real-time PCR) brings a more efficient and accurate method for detecting and analyzing nucleic acids in hospitals and laboratories. To solve the inconvenience of PCR reagent delivery and storage via cold-chain transportation, a solid-state reagent with robust characteristics should be employed. In this report, a lyophilized mix containing all necessary components for real-time PCR and its production method was designed, and its stability was tested at different temperatures. Some cryoprotectants and carriers are required to protect the function of the enzyme and primer as much as possible and provide the cake structure. Formulations with polyhydroxy compounds were considered to have the potential for protecting the enzymatic microstructure and functionality of dried mixes during the whole manufacturing and cold-free storage. The final products with the most superior protective formulation containing trehalose, Ficoll 400, and gelatin were able to provide the totally same testing result and sensitivity as the freshly made mix after 300 days of storage at 45 °C and can be deduced to maintain the function at room temperature (22.5–25.5 °C) for about 2 years.