Maninder S. Grover
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Maninder S. Grover has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Paolo Valentini
Air Force Research Laboratory
10 shared publications - Nicholas J. Bisek
Air Force Research Laboratory, Wright-Patterson Air Force Base, OH 45433, USA
9 shared publications - Ashley M. Verhoff
Air Force Research Laboratory 2 , Wright-Patterson Air Force Base, Ohio 45433, USA
5 shared publications Richard L. Jaffe
NASA Ames Research Center, Moffett Field, California 94035, USA
1 shared publicationThomas E. Schwartzentruber
Department of Aerospace Engineering and Mechanics, University of Minnesota, Minneapolis, Minnesota 55455, USA
1 shared publication
Latest Publications
- Open Access
- 7 February 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (6) , eads2147
Ab initio investigation of a hypersonic double cone experiment
This article presents a direct molecular simulation (DMS) of a reactive Mach 8.2 oxygen flow over a double cone geometry. The free stream conditions and article configuration generate a flow with thermal and chemical nonequilibrium, which are common attributes of hypersonic flight. This scenario was first studied experimentally at Calspan University of Buffalo Research Center’s test facility. DMS is a particle method that uses quantum mechanically derived interaction potentials to simulate molecular collisions within a flow field. Since these interaction potentials are the only modeling inputs used in the simulation, all flow features can solely be attributed to the ab initio potential energy surfaces. Hence, providing a comparison of a hypersonic ground test and numerical data anchored to quantum mechanics. The fundamental nature of DMS is leveraged to investigate molecular level mechanisms prevalent in the flow, and comparisons with lower fidelity simulations are presented to highlight the role of these first principles calculations as benchmark solutions.
- 7 February 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (6) , eads2147
Open AccessAb initio investigation of a hypersonic double cone experiment
This article presents a direct molecular simulation (DMS) of a reactive Mach 8.2 oxygen flow over a double cone geometry. The free stream conditions and article configuration generate a flow with thermal and chemical nonequilibrium, which are common attributes of hypersonic flight. This scenario was first studied experimentally at Calspan University of Buffalo Research Center’s test facility. DMS is a particle method that uses quantum mechanically derived interaction potentials to simulate molecular collisions within a flow field. Since these interaction potentials are the only modeling inputs used in the simulation, all flow features can solely be attributed to the ab initio potential energy surfaces. Hence, providing a comparison of a hypersonic ground test and numerical data anchored to quantum mechanics. The fundamental nature of DMS is leveraged to investigate molecular level mechanisms prevalent in the flow, and comparisons with lower fidelity simulations are presented to highlight the role of these first principles calculations as benchmark solutions.
- Open Access
- 10 October 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 997, A27
Toward ab initio molecular simulation of reacting air: Mach 15 air flow over a blunt wedge
We present a Mach 15 air flow over a blunt two-dimensional wedge simulated using the direct molecular simulation method. As electronically excited states are not modelled, the resulting air mixture around the wedge contains the electronic ground states only, namely ${\rm N}_2(\text {X}^1 \varSigma _g^{+})$ , ${\rm O}_2(\text {X}^3 \varSigma _g^{-})$ , ${\rm NO}(\text {X}^2\varPi _r)$ , ${\rm N}(^4{\rm S})$ and ${\rm O}(^3{\rm P})$ . All the potential energy surfaces (PESs) that are used to model the various interactions between air particles are ab initio, with two notable exceptions, namely ${\rm N}_2+{\rm NO}$ and ${\rm O}_2+{\rm NO}$ . At the selected free-stream conditions, strong vibrational non-equilibrium is observed in the shock layer. The flow is characterized by significant chemical activity, with near-complete oxygen dissociation, considerable formation of NO and minimal molecular nitrogen dissociation. Complex mass diffusion kinetics, driven by composition, temperature and pressure gradients, are identified in the shock layer. All these physical phenomena are directly coupled to, and responsible for, the mechanics of the gas flow and are all solely traceable to the PESs’ inputs, without the need for any thermochemical models, mixing rules or constitutive laws for transport properties. Because the flow is entirely at near-continuum conditions, it is a gas-phase thermophysics benchmark that is useful to enhance the fidelity of continuum models used in computational fluid dynamics of hypersonic flows.- 10 October 2024
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 997, A27
Open AccessToward ab initio molecular simulation of reacting air: Mach 15 air flow over a blunt wedge
We present a Mach 15 air flow over a blunt two-dimensional wedge simulated using the direct molecular simulation method. As electronically excited states are not modelled, the resulting air mixture around the wedge contains the electronic ground states only, namely ${\rm N}_2(\text {X}^1 \varSigma _g^{+})$ , ${\rm O}_2(\text {X}^3 \varSigma _g^{-})$ , ${\rm NO}(\text {X}^2\varPi _r)$ , ${\rm N}(^4{\rm S})$ and ${\rm O}(^3{\rm P})$ . All the potential energy surfaces (PESs) that are used to model the various interactions between air particles are ab initio, with two notable exceptions, namely ${\rm N}_2+{\rm NO}$ and ${\rm O}_2+{\rm NO}$ . At the selected free-stream conditions, strong vibrational non-equilibrium is observed in the shock layer. The flow is characterized by significant chemical activity, with near-complete oxygen dissociation, considerable formation of NO and minimal molecular nitrogen dissociation. Complex mass diffusion kinetics, driven by composition, temperature and pressure gradients, are identified in the shock layer. All these physical phenomena are directly coupled to, and responsible for, the mechanics of the gas flow and are all solely traceable to the PESs’ inputs, without the need for any thermochemical models, mixing rules or constitutive laws for transport properties. Because the flow is entirely at near-continuum conditions, it is a gas-phase thermophysics benchmark that is useful to enhance the fidelity of continuum models used in computational fluid dynamics of hypersonic flows. - 1 May 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (5)
Validity of Stokes' hypothesis for near-continuum hypersonic flows
The alternative interpretation of Stokes' hypothesis provided by Buresti [Acta Mech. 226, 3555–3559 (2015)] is investigated by an analysis of a near-continuum, hypersonic flow of oxygen over a double cone obtained from a large-scale direct simulation Monte Carlo computation. We show that for molecular oxygen, which has comparable bulk and shear viscosity coefficients, the difference between mechanical and thermodynamic pressure is negligible throughout most of the flow. This result justifies neglecting viscous stresses in the normal stress tensor associated with fluid particle dilatation, as is often done in continuum descriptions of compressible flows. The violation of the revisited Stokes' hypothesis was only observed in highly nonequilibrium regions of the flow (shocks and strong expansions) and wherever non-continuum effects become significant. For nonequilibrium flows of gases with large bulk viscosity relative to their shear viscosity, the revisited Stokes' assumption may still breakdown and requires further investigation.
- 1 May 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (5)
Validity of Stokes' hypothesis for near-continuum hypersonic flows
The alternative interpretation of Stokes' hypothesis provided by Buresti [Acta Mech. 226, 3555–3559 (2015)] is investigated by an analysis of a near-continuum, hypersonic flow of oxygen over a double cone obtained from a large-scale direct simulation Monte Carlo computation. We show that for molecular oxygen, which has comparable bulk and shear viscosity coefficients, the difference between mechanical and thermodynamic pressure is negligible throughout most of the flow. This result justifies neglecting viscous stresses in the normal stress tensor associated with fluid particle dilatation, as is often done in continuum descriptions of compressible flows. The violation of the revisited Stokes' hypothesis was only observed in highly nonequilibrium regions of the flow (shocks and strong expansions) and wherever non-continuum effects become significant. For nonequilibrium flows of gases with large bulk viscosity relative to their shear viscosity, the revisited Stokes' assumption may still breakdown and requires further investigation.
- 9 January 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (1) , 013401
Molecular diffusion of mass and energy predicted by ab initio potential energy surfaces for air components at high temperatures
The thermal conductivity and self-diffusion coefficients for molecular nitrogen and oxygen are investigated with the direct molecular simulation (DMS) technique using high-fidelity, ab initio potential energy surfaces. The DMS results are compared to available experimental data, and remarkable agreement is observed in all cases. Such comparisons are restricted to relatively low temperature, typically below 2000 K. For temperatures up to 10 000 K, the DMS data are also in excellent agreement with the corresponding transport properties obtained using kinetic theory based on collision integrals evaluated with simplified, point-particle interatomic potentials. An analysis of the Eucken approximation shows that the Eucken correction factor is based upon reasonably accurate assumptions, but a significant improvement can be obtained by properly accounting for the ratio of mass to momentum diffusion. Finally, it is shown that the DMS transport data for mass, momentum, and energy are consistent with kinetic theory across a wide range of temperatures, thus offering convincing evidence for the reliability of the methodologies employed for their determination.
- 9 January 2024
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 9 (1) , 013401
Molecular diffusion of mass and energy predicted by ab initio potential energy surfaces for air components at high temperatures
The thermal conductivity and self-diffusion coefficients for molecular nitrogen and oxygen are investigated with the direct molecular simulation (DMS) technique using high-fidelity, ab initio potential energy surfaces. The DMS results are compared to available experimental data, and remarkable agreement is observed in all cases. Such comparisons are restricted to relatively low temperature, typically below 2000 K. For temperatures up to 10 000 K, the DMS data are also in excellent agreement with the corresponding transport properties obtained using kinetic theory based on collision integrals evaluated with simplified, point-particle interatomic potentials. An analysis of the Eucken approximation shows that the Eucken correction factor is based upon reasonably accurate assumptions, but a significant improvement can be obtained by properly accounting for the ratio of mass to momentum diffusion. Finally, it is shown that the DMS transport data for mass, momentum, and energy are consistent with kinetic theory across a wide range of temperatures, thus offering convincing evidence for the reliability of the methodologies employed for their determination.
- Open Access
- 1 August 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (8)
First principles simulation of reacting hypersonic flow over a blunt wedge
This article presents molecular-level analysis of a reactive, near-continuum, Mach 21 nitrogen flow over a blunt wedge using the direct molecular simulation (DMS) method. The flow conditions lead to internal energy excitation and dissociation in the flow field, resulting in thermal and chemical nonequilibrium in the flow. Thermal nonequilibrium in the vibrational mode is observed to extend to the molecular level, where the vibrational energy distributions at various points in the flow field are observed to be non-Boltzmann. Furthermore, this is the first reactive DMS calculation where the wall is assumed to be isothermal and full momentum accommodation of the particles is enforced, hence incorporating viscous wall effects. Since the DMS method uses a quantum mechanically generated interaction potential as its only modeling input, all thermochemical and transport properties of the flow field can directly be attributed to the ab initio potential energy surface. Using the DMS solution as a benchmark, this article assesses the performance of Navier–Stokes computational fluid dynamics solutions using lower fidelity two-temperature models. Two models are chosen as points of comparison: the well-known Park two-temperature model and the recently developed modified Marrone and Treanor model.
- 1 August 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (8)
Open AccessFirst principles simulation of reacting hypersonic flow over a blunt wedge
This article presents molecular-level analysis of a reactive, near-continuum, Mach 21 nitrogen flow over a blunt wedge using the direct molecular simulation (DMS) method. The flow conditions lead to internal energy excitation and dissociation in the flow field, resulting in thermal and chemical nonequilibrium in the flow. Thermal nonequilibrium in the vibrational mode is observed to extend to the molecular level, where the vibrational energy distributions at various points in the flow field are observed to be non-Boltzmann. Furthermore, this is the first reactive DMS calculation where the wall is assumed to be isothermal and full momentum accommodation of the particles is enforced, hence incorporating viscous wall effects. Since the DMS method uses a quantum mechanically generated interaction potential as its only modeling input, all thermochemical and transport properties of the flow field can directly be attributed to the ab initio potential energy surface. Using the DMS solution as a benchmark, this article assesses the performance of Navier–Stokes computational fluid dynamics solutions using lower fidelity two-temperature models. Two models are chosen as points of comparison: the well-known Park two-temperature model and the recently developed modified Marrone and Treanor model.
- Open Access
- 4 July 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 966, A32
Near-continuum, hypersonic oxygen flow over a double cone simulated by direct simulation Monte Carlo informed from quantum chemistry
A large-scale, fully resolved direct simulation Monte Carlo (DSMC) computation of a non-equilibrium, reactive flow of pure oxygen over a double cone is presented. Under the simulated near-continuum conditions, the computational demands are shown to be significant because of the wide range of length scales that must be resolved. Therefore, robust grid adaption capabilities and efficient parallelization of the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code that is utilized in this work are essential. The thermochemical and transport collision models were selected for efficiency and simplicity. First-principles data, obtained from the highly accurate direct molecular simulation method, were used to inform the collision models’ parameters. Importantly, because SPARTA implements molecular collision models using collision-specific energies, the resulting macroscopic relaxation rates were evaluateda posteriorivia zero-dimensional heat bath simulations. The comparisons of surface properties, namely heat flux and pressure, show very close agreement with previous computational fluid dynamics (CFD) results. Differences with the measurements were found to be similar to the CFD simulations. The unresolved discrepancy with the measurements could be due to inconsistent free stream conditions with the actual experimental data or missing physical phenomena altogether, for example atomic and molecular oxygen electronically excited states, three-dimensional effects, or more complex gas–surface interactions. As shown in this work, the advantages of obtaining a DSMC particle solution for these flows reside in the method's ability to be directly informed from first principles and to seamlessly describe internal energy non-equilibrium for all modes. With the advent of exascale computing and beyond, particle methods will be an increasingly important tool to verify the validity of physical assumptions in reduced-order models via fully resolved, experimental-scale simulations, down to the level of molecular-level distributions.
- 4 July 2023
- Published by Cambridge University Press (CUP) in Journal of Fluid Mechanics
- Vol. 966, A32
Open AccessNear-continuum, hypersonic oxygen flow over a double cone simulated by direct simulation Monte Carlo informed from quantum chemistry
A large-scale, fully resolved direct simulation Monte Carlo (DSMC) computation of a non-equilibrium, reactive flow of pure oxygen over a double cone is presented. Under the simulated near-continuum conditions, the computational demands are shown to be significant because of the wide range of length scales that must be resolved. Therefore, robust grid adaption capabilities and efficient parallelization of the Stochastic PArallel Rarefied-gas Time-accurate Analyzer (SPARTA) code that is utilized in this work are essential. The thermochemical and transport collision models were selected for efficiency and simplicity. First-principles data, obtained from the highly accurate direct molecular simulation method, were used to inform the collision models’ parameters. Importantly, because SPARTA implements molecular collision models using collision-specific energies, the resulting macroscopic relaxation rates were evaluateda posteriorivia zero-dimensional heat bath simulations. The comparisons of surface properties, namely heat flux and pressure, show very close agreement with previous computational fluid dynamics (CFD) results. Differences with the measurements were found to be similar to the CFD simulations. The unresolved discrepancy with the measurements could be due to inconsistent free stream conditions with the actual experimental data or missing physical phenomena altogether, for example atomic and molecular oxygen electronically excited states, three-dimensional effects, or more complex gas–surface interactions. As shown in this work, the advantages of obtaining a DSMC particle solution for these flows reside in the method's ability to be directly informed from first principles and to seamlessly describe internal energy non-equilibrium for all modes. With the advent of exascale computing and beyond, particle methods will be an increasingly important tool to verify the validity of physical assumptions in reduced-order models via fully resolved, experimental-scale simulations, down to the level of molecular-level distributions.
- 8 December 2022
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 7 (12) , 123401
Comparative analysis of internal energy excitation and dissociation of nitrogen predicted by independently developed ab initio potential energy surfaces
In this article we present a comparative atomic level study analyzing the vibrational excitation and dissociation of molecular nitrogen due to and interactions governed by independently developed potential energy surfaces at the University of Minnesota and NASA Ames Research Center. Vibrational excitation was studied for interactions from to K and for from to K. Nonequilibrium dissociation is studied from to K under the quasi-steady-state condition for and interactions. Finally, an inviscid Mach 20 dissociating nitrogen flow over a cylinder with a Knudsen number of 0.015 is carried out to study the impact of molecular interactions predicted by independently developed potential energy surfaces on a canonical hypersonic flow.- 8 December 2022
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 7 (12) , 123401
Comparative analysis of internal energy excitation and dissociation of nitrogen predicted by independently developed ab initio potential energy surfaces
In this article we present a comparative atomic level study analyzing the vibrational excitation and dissociation of molecular nitrogen due to and interactions governed by independently developed potential energy surfaces at the University of Minnesota and NASA Ames Research Center. Vibrational excitation was studied for interactions from to K and for from to K. Nonequilibrium dissociation is studied from to K under the quasi-steady-state condition for and interactions. Finally, an inviscid Mach 20 dissociating nitrogen flow over a cylinder with a Knudsen number of 0.015 is carried out to study the impact of molecular interactions predicted by independently developed potential energy surfaces on a canonical hypersonic flow.- 18 July 2022
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 7 (7) , L071401
Ab initiocalculation of thermal conductivity: Application to molecular nitrogen
A method to compute the thermal conductivity of a dilute gas from stochastic particle methods is described. The proposed approach is inspired by the Müller-Plathe method, in that the heat flux is imposed on the system and is precisely known, whereas the temperature gradient is sampled during the simulation. In this manner, the issue of large statistical scatter associated with sampling the heat flux is circumvented. The modified Müller-Plathe (MMP) method is first verified with a standard variable hard sphere direct simulation Monte Carlo calculation. Then, it is used in direct molecular simulation (DMS) equipped with an ab initio potential energy surface. The most significant sources of uncertainty are clearly identified and discussed. The DMS results for molecular nitrogen thermal conductivity agree remarkably well with the experimental evidence up to 2 000 K. The proposed MMP technique is applicable to arbitrary interatomic potentials and gas compositions, and it provides a direct way to evaluate thermal conductivity without relying on empirical extrapolations to high temperatures or approximations based on viscosity.- 18 July 2022
- Published by American Physical Society (APS) in Physical Review Fluids
- Vol. 7 (7) , L071401
Ab initiocalculation of thermal conductivity: Application to molecular nitrogen
A method to compute the thermal conductivity of a dilute gas from stochastic particle methods is described. The proposed approach is inspired by the Müller-Plathe method, in that the heat flux is imposed on the system and is precisely known, whereas the temperature gradient is sampled during the simulation. In this manner, the issue of large statistical scatter associated with sampling the heat flux is circumvented. The modified Müller-Plathe (MMP) method is first verified with a standard variable hard sphere direct simulation Monte Carlo calculation. Then, it is used in direct molecular simulation (DMS) equipped with an ab initio potential energy surface. The most significant sources of uncertainty are clearly identified and discussed. The DMS results for molecular nitrogen thermal conductivity agree remarkably well with the experimental evidence up to 2 000 K. The proposed MMP technique is applicable to arbitrary interatomic potentials and gas compositions, and it provides a direct way to evaluate thermal conductivity without relying on empirical extrapolations to high temperatures or approximations based on viscosity.- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 096108
Molecular simulation of flows in thermochemical non-equilibrium around a cylinder using ab initio potential energy surfaces for N2 + N and N2 + N2 interactions
We present two-dimensional direct molecular simulation (DMS) results for high-enthalpy nitrogen flows in thermochemical non-equilibrium around a circular cylinder. The simulations are carried out using accurate ab initio potential energy surfaces (PES) to describe N2 + N and N2 + N2 interactions. Select comparisons with the direct simulation Monte Carlo method are presented to demonstrate how the high-fidelity DMS data, both at the level of bulk flow quantities and local molecular distributions, can be used to thoroughly inform or validate simplified reduced-order descriptions. Then, a partially dissociated nitrogen flow around a circular cylinder is obtained from two successive refinements of a well-established ab initio nitrogen PES. The only input in both calculations is the respective PESs, all other simulation parameters being precisely equal. This work, enabled by large scale computing, represents the first attempt at establishing a rigorous methodology for (i) the validation of lower-fidelity, computationally efficient models using ab initio, assumption-free calculations (DMS) as benchmarks and (ii) a systematic assessment of ab initio PES accuracy using entire flow field results.
- 1 September 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (9) , 096108
Molecular simulation of flows in thermochemical non-equilibrium around a cylinder using ab initio potential energy surfaces for N2 + N and N2 + N2 interactions
We present two-dimensional direct molecular simulation (DMS) results for high-enthalpy nitrogen flows in thermochemical non-equilibrium around a circular cylinder. The simulations are carried out using accurate ab initio potential energy surfaces (PES) to describe N2 + N and N2 + N2 interactions. Select comparisons with the direct simulation Monte Carlo method are presented to demonstrate how the high-fidelity DMS data, both at the level of bulk flow quantities and local molecular distributions, can be used to thoroughly inform or validate simplified reduced-order descriptions. Then, a partially dissociated nitrogen flow around a circular cylinder is obtained from two successive refinements of a well-established ab initio nitrogen PES. The only input in both calculations is the respective PESs, all other simulation parameters being precisely equal. This work, enabled by large scale computing, represents the first attempt at establishing a rigorous methodology for (i) the validation of lower-fidelity, computationally efficient models using ab initio, assumption-free calculations (DMS) as benchmarks and (ii) a systematic assessment of ab initio PES accuracy using entire flow field results.
- 1 May 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (5) , 051704
Ab initio simulation of hypersonic flows past a cylinder based on accurate potential energy surfaces
For the first time in the literature, we present 2D simulations of hypersonic flows around a cylinder obtained from accurate ab initio potential energy surfaces (PESs). We compare results obtained from a low fidelity (empirical) and a high fidelity (ab initio) PES, thus demonstrating the impact of PES accuracy on the entire aerothermodynamic field around the body. We observe that the empirical PES is not adequate to accurately reproduce rotational and vibrational relaxation in the hypersonic flow, both in the compression and expansion regions of the flow field. This approach, enabled by advancements in large-scale computing, paves the way to the direct simulation of hypersonic flows where the only modeling input is the PES that describes molecular interactions between the various air constituents. Such flow field simulations provide benchmark solutions for the validation of reduced-order models.
- 1 May 2021
- Published by AIP Publishing in Physics of Fluids
- Vol. 33 (5) , 051704
Ab initio simulation of hypersonic flows past a cylinder based on accurate potential energy surfaces
For the first time in the literature, we present 2D simulations of hypersonic flows around a cylinder obtained from accurate ab initio potential energy surfaces (PESs). We compare results obtained from a low fidelity (empirical) and a high fidelity (ab initio) PES, thus demonstrating the impact of PES accuracy on the entire aerothermodynamic field around the body. We observe that the empirical PES is not adequate to accurately reproduce rotational and vibrational relaxation in the hypersonic flow, both in the compression and expansion regions of the flow field. This approach, enabled by advancements in large-scale computing, paves the way to the direct simulation of hypersonic flows where the only modeling input is the PES that describes molecular interactions between the various air constituents. Such flow field simulations provide benchmark solutions for the validation of reduced-order models.