KJKiseok Jeon

Kiseok Jeon

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kiseok Jeon has a total of 18 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Electrical Analysis of Non-Destructive-Cut HPBC Solar Cells via Crack Driving Index

    by Woocheol Choi, Min Kwak, Geonu Kim, Jinho Shin, Kiseok Jeon, Jinyong Seok, Chaehwan Jeong

    Non-destructive cutting (NDC) is promising for fabricating high-efficiency half-cut solar cells by minimizing thermal and mechanical damage during cell cutting. Here, a dual-laser NDC process, comprising an infrared (IR) laser for pre-cut formation and a thermal laser for crack propagation, was applied to hybrid passivated back contact solar cells. Accordingly, the effects of scan speed, IR laser-induced pre-cut depth, and thermal laser power were systematically investigated at scan speeds of 300, 400, and 500 mm/s. Furthermore, stable process windows for cleaving were identified, within which fill factor and maximum power were evaluated. Despite differences in absolute laser power and scan speed, the highest electrical performance was consistently achieved at an intermediate pre-cut depth combined with the maximum thermal laser power available within each process window. To elucidate this behavior, a crack-driving index (ψ) was introduced to consider the coupled effects of thermal driving and crack guidance. The ψ-based analysis reveals that higher scan speeds enhance process sensitivity, highlighting a trade-off between peak performance and process robustness.


  • Open Access

    Low-Thermal-Budget Enhancement of Electrically Conductive Adhesive Interconnection for HPBC Photovoltaic Modules

    by Min Kwak, Woocheol Choi, Geonu Kim, Kiseok Jeon, Jinyong Seok, Jinho Shin, Chaehwan Jeong

    The growing demand for high-efficiency photovoltaic (PV) technologies has intensified interest in advanced cell architectures, including hybrid passivated back contact (HPBC) solar cells. Conventional solder-based interconnection processes require high thermal budgets, which can induce thermomechanical stress and lead to performance degradation in thin back-contact cell structures. In this study, electrically conductive adhesive (ECA) interconnection is investigated as a low-thermal-budget, solder-free alternative for HPBC solar cells. The curing behavior of an acrylic-based, silver-filled ECA is systematically examined by controlling the upper lamp temperature and the welding time during the interconnection process. Electrical performance is evaluated through current–voltage characterization, fill factor, and series resistance analysis, while interfacial microstructural evolution is examined using scanning electron microscopy. The results identify a well-defined processing window in which adequate curing enables stable electrical contact formation. In contrast, both insufficient curing and excessive curing result in degraded electrical performance. To assess practical applicability, HPBC modules with an industry-relevant size of ~1000 × 1160 mm2 are fabricated and evaluated using electroluminescence imaging and I–V measurements. By identifying a robust curing window and demonstrating its successful transfer from string-level interconnections to full-size HPBC modules, this study establishes a practical, low-thermal-budget, solder-free interconnection strategy for advanced back-contact PV architectures.

  • Open Access

    Fabrication of Thermally Evaporated CuIx Thin Films and Their Characteristics for Solar Cell Applications

    by Kiseok Jeon, Min-Joon Park, Sung-Min Youn, Sangwoo Lim, Chaehwan Jeong

    Carrier-selective contacts (CSCs) for high-efficiency heterojunction solar cells have been widely studied due to their advantages of processing at relatively low temperatures and simple fabrication processes. Transition metal oxide (TMO) (e.g., molybdenum oxide, vanadium oxide, and tungsten oxide) thin films are widely used as hole-selective contacts (HSCs, required work function for Si solar cells > 5.0 eV). However, when TMO thin films are used, difficulties are faced in uniform deposition. In this study, we fabricated a copper (I) iodide (CuI) thin film (work function > 5.0 eV) that remained relatively stable during atmospheric exposure compared with TMO thin films and employed it as an HSC layer in an n-type Si solar cell. To facilitate efficient hole collection, we conducted iodine annealing at temperatures of 100–180 °C to enhance the film’s electrical characteristics (carrier density and carrier mobility). Subsequently, we fabricated CSC Si solar cells using the annealed CuIx layer, which achieved an efficiency of 6.42%.


  • Open Access

    Optimization of Shingled-Type Lightweight Glass-Free Solar Modules for Building Integrated Photovoltaics

    by Min-Joon Park, Sungmin Youn, Kiseok Jeon, Soo Ho Lee, Chaehwan Jeong

    High-power and lightweight photovoltaic (PV) modules are suitable for building-integrated photovoltaic (BIPV) systems. Due to the characteristics of the installation sites, the BIPV solar modules are limited by weight and installation area. In this study, we fabricated glass-free and shingled-type PV modules with an area of 1040 mm × 965 mm, which provide more conversion power compared to conventional PV modules at the same installed area. Further, we employed an ethylene tetrafluoroethylene sheet instead of a front cover glass and added an Al honeycomb sandwich structure to enhance the mechanical stability of lightweight PV modules. To optimize the conversion power of the PV module, we adjusted the amount of dispensed electrically conductive adhesives between the solar cells. Finally, we achieved a conversion power of 195.84 W at an area of 1.004 m2, and we performed standard reliability tests using a PV module that weighed only 9 kg/m2.


  • Open Access

    Fabrication of Large Area, Ordered Nanoporous Structures on Various Substrates for Potential Electro-Optic Applications

    by Hongsub Jee, Kiseok Jeon, Min-Joon Park, Jaehyeong Lee

    Nanoporous structures have attracted great attention in electronics, sensor and storage devices, and photonics because of their large surface area, large volume to surface ratio, and potential for high-sensitivity sensor applications. Normally, electron or ion beam patterning can be used for nanopores fabrication by direct writing. However, direct writing is a rather expensive and time-consuming method due to its serial nature. Therefore, it may not translate to a preferred manufacturing process. In this research, a perfectly ordered large-area periodic pattern in an area of approximately 1 cm2 has been successfully fabricated on various substrates including glass, silicon, and polydimethylsiloxane, using a two-step process comprising visible light-based multibeam interference lithography and subsequent pattern transfer processes of reactive ion etching and nanomolding. Additionally, the multibeam interference lithography templated anodized aluminum oxide process has been described. Since the fabrication area in multibeam interference lithography can be extended by using a larger beam size, it is highly cost effective and manufacturable. Furthermore, although not described here, an electrodeposition process can be utilized as a pattern transfer process. This large-area perfectly ordered nanopore array will be very useful for high-density electronic memory and photonic bandgap and metamaterial applications.


  • Open Access

    Combining Interference Lithography and Two-Photon Lithography for Fabricating Large-Area Photonic Crystal Structures with Controlled Defects

    by Hongsub Jee, Min-Joon Park, Kiseok Jeon, Chaehwan Jeong, Jaehyeong Lee

    Interference lithography is a promising method for fabricating large-area, defect-free three-dimensional photonic crystal structures which can be used for facilitating the realization of photonic devices with a fast processing time. Although they can be used in waveguides, resonators, and detectors, their repeated regular array patterns can only be used for limited applications. In this study, we demonstrate a method for fabricating large-area photonic crystal structures with controlled defects by combining interference lithography and two-photon lithography using a light-curable resin. By combining regular array structures and controlled patterns, monotonous but large-area regular structures can be obtained. Furthermore, the patterned structures have considerable potential for use in various applications, such as solar cells, sensors, photodetectors, micro-/nano-electronics, and cell growth.


  • Open Access

    Characteristics and Electronic Band Alignment of a Transparent p-CuI/n-SiZnSnO Heterojunction Diode with a High Rectification Ratio

    by Jeong Hyuk Lee, Byeong Hyeon Lee, Jeonghun Kang, Mangesh Diware, Kiseok Jeon, Chaehwan Jeong, Sang Yeol Lee, Kee Hoon Kim

    Transparent p-CuI/n-SiZnSnO (SZTO) heterojunction diodes are successfully fabricated by thermal evaporation of a (111) oriented p-CuI polycrystalline film on top of an amorphous n-SZTO film grown by the RF magnetron sputtering method. A nitrogen annealing process reduces ionized impurity scattering dominantly incurred by Cu vacancy and structural defects at the grain boundaries in the CuI film to result in improved diode performance; the current rectification ratio estimated at ±2 V is enhanced from ≈106 to ≈107. Various diode parameters, including ideality factor, reverse saturation current, offset current, series resistance, and parallel resistance, are estimated based on the Shockley diode equation. An energy band diagram exhibiting the type-II band alignment is proposed to explain the diode characteristics. The present p-CuI/n-SZTO diode can be a promising building block for constructing useful optoelectronic components such as a light-emitting diode and a UV photodetector.