Senthilraja Shanmugasundaram
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Senthilraja Shanmugasundaram has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
R. Gangadevi
2 shared publications- Rajendiran Gangadevi
SRM Institute of Science and Technology
2 shared publications A. Nikhil
1 shared publicationAmmar H. Elsheikh
1 shared publicationB. C. Mohana Gokul
1 shared publication- Babu Munirathinam
Department of Information Technology, Rajalakshmi Engineering College, Thandalam, Chennai, 602 105, Tamil Nadu, India
1 shared publication
Latest Publications
- Open Access
- 21 September 2026
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- Vol. 20 (3) , 126-131
Design and Development of Vacuum Actuated Soft Gripper for Pick and Place Different Irregular Shaped Objects
This article presents the design, fabrication and testing of a novel vacuum based soft robotic gripper. This work included the fabrication of a cylindrical gripper via a 3D-printed mould, into which a combination of liquid silicone elastomer and curing agent was injected. The deformation behavior of the soft gripper was analyzed for different pressures using ANSYS software. The ANSYS results revealed that the pressure, material and size of the cavity inside the gripper are the important factor that affects the deformation of the soft gripper. Finally the grasping power and holding time of the fabricated gripper has been tested by grasping different objects including fruits, mobile phone, plastic bottles and stainless steel utensils. The validation findings demonstrate the gripping and holding capabilities of the proposed vacuum gripper, suggesting its suitability for various automation and industrial applications.
- 21 September 2026
- Published by PIAP - Industrial Research Institute for Automation and Measurements in Journal of Automation, Mobile Robotics and Intelligent Systems
- Vol. 20 (3) , 126-131
Open AccessDesign and Development of Vacuum Actuated Soft Gripper for Pick and Place Different Irregular Shaped Objects
This article presents the design, fabrication and testing of a novel vacuum based soft robotic gripper. This work included the fabrication of a cylindrical gripper via a 3D-printed mould, into which a combination of liquid silicone elastomer and curing agent was injected. The deformation behavior of the soft gripper was analyzed for different pressures using ANSYS software. The ANSYS results revealed that the pressure, material and size of the cavity inside the gripper are the important factor that affects the deformation of the soft gripper. Finally the grasping power and holding time of the fabricated gripper has been tested by grasping different objects including fruits, mobile phone, plastic bottles and stainless steel utensils. The validation findings demonstrate the gripping and holding capabilities of the proposed vacuum gripper, suggesting its suitability for various automation and industrial applications.
- 1 July 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (14) , 1-13
Impact of quenching with Al2O3/water nanofluid on the mechanical properties and microstructure of carbon steel
- 1 July 2026
- Published by Springer Nature in Journal of Thermal Analysis and Calorimetry
- Vol. 151 (14) , 1-13
Impact of quenching with Al2O3/water nanofluid on the mechanical properties and microstructure of carbon steel
- 1 May 2026
- Published by Springer Nature
- p. 113-120
Design and Development of Magneto Rheological (MR) Fluid Based Soft Gripper
- 1 May 2026
- Published by Springer Nature
- p. 113-120
Design and Development of Magneto Rheological (MR) Fluid Based Soft Gripper
- Open Access
- 8 April 2025
- Published by Sultan Qaboos University in The Journal of Engineering Research
- Vol. 21 (1) , 1-7
Integrated AHP – TOPSIS Approach for Optimization of Coolant with Nanoparticles in PVT-Based Hydrogen Production System
The production of hydrogen using photovoltaic–thermal (PVT) solar collectors with minimal environmental impact is a significant issue that necessitates a methodical approach. The selection of an appropriate nanofluid is essential in a thermal collector to optimize the performance of the photovoltaic-thermal (PVT) system and increase the rate of hydrogen production. This study analyzes several nanofluids in terms of viscosity, thermal conductivity, density, specific heat, pumping power, and fluid cost. This study discovered a nanofluid that may significantly enhance the rate of hydrogen generation. To achieve this objective, the analytical hierarchy process (AHP) and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) methods were used to identify the appropriate choice and assess the hydrogen production rate. First, the AHP technique was used to determine the required weights, followed by sorting the alternatives using the TOPSIS technique. The findings indicate that a hybrid nanofluid consisting of a 0.2% volume concentration of Al2O3–CuO in water exhibits the most favourable heat transfer characteristics and is considered the best option for improving heat transfer efficiency and boosting the rate of hydrogen generation.
- 8 April 2025
- Published by Sultan Qaboos University in The Journal of Engineering Research
- Vol. 21 (1) , 1-7
Open AccessIntegrated AHP – TOPSIS Approach for Optimization of Coolant with Nanoparticles in PVT-Based Hydrogen Production System
The production of hydrogen using photovoltaic–thermal (PVT) solar collectors with minimal environmental impact is a significant issue that necessitates a methodical approach. The selection of an appropriate nanofluid is essential in a thermal collector to optimize the performance of the photovoltaic-thermal (PVT) system and increase the rate of hydrogen production. This study analyzes several nanofluids in terms of viscosity, thermal conductivity, density, specific heat, pumping power, and fluid cost. This study discovered a nanofluid that may significantly enhance the rate of hydrogen generation. To achieve this objective, the analytical hierarchy process (AHP) and Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) methods were used to identify the appropriate choice and assess the hydrogen production rate. First, the AHP technique was used to determine the required weights, followed by sorting the alternatives using the TOPSIS technique. The findings indicate that a hybrid nanofluid consisting of a 0.2% volume concentration of Al2O3–CuO in water exhibits the most favourable heat transfer characteristics and is considered the best option for improving heat transfer efficiency and boosting the rate of hydrogen generation.
- 29 December 2023
- Published by Elsevier in Environmental Research
- Vol. 246, 118089
Assessment of cyclone risk and case study of Gaja cyclone using GIS techniques and machine learning algorithms in coastal zone of Tamil Nadu, India
- 29 December 2023
- Published by Elsevier in Environmental Research
- Vol. 246, 118089
Assessment of cyclone risk and case study of Gaja cyclone using GIS techniques and machine learning algorithms in coastal zone of Tamil Nadu, India
- Open Access
- 1 January 2023
- Published by University of Zielona Góra, Poland in Civil and Environmental Engineering Reports
- Vol. 33 (4) , 123-150
Selection of Robot for Contour Crafting Using Analytical Hierarchy Process
The use of robotic equipment and a new technique called contour crafting allows for the construction of buildings at lower labor and material costs. The selection of the type of robot is an important factor that affects the overall performance of the contour crafting (CC) system. Various robot configurations, such as gantry, cylindrical, and SCARA, may be employed for contour crafting. There are benefits and drawbacks to using different types of robots for various tasks, including cost, work volume, material compatibility, and precision. Identifying a proper robot using the multi-criterion decision-making (MCDM) technique is crucial for successful building automation. This article uses the analytical hierarchy process (AHP) method to rank the best robots according to several characteristics. Cartesian robots, cylindrical robots, and SCARA robots were evaluated based on cost, accuracy, work volume, surface finish, type of profile, and speed. The results showed that the gantry-type robot is the most suitable option, while the cylindrical robot is unsuitable for building construction due to lower accuracy.
- 1 January 2023
- Published by University of Zielona Góra, Poland in Civil and Environmental Engineering Reports
- Vol. 33 (4) , 123-150
Open AccessSelection of Robot for Contour Crafting Using Analytical Hierarchy Process
The use of robotic equipment and a new technique called contour crafting allows for the construction of buildings at lower labor and material costs. The selection of the type of robot is an important factor that affects the overall performance of the contour crafting (CC) system. Various robot configurations, such as gantry, cylindrical, and SCARA, may be employed for contour crafting. There are benefits and drawbacks to using different types of robots for various tasks, including cost, work volume, material compatibility, and precision. Identifying a proper robot using the multi-criterion decision-making (MCDM) technique is crucial for successful building automation. This article uses the analytical hierarchy process (AHP) method to rank the best robots according to several characteristics. Cartesian robots, cylindrical robots, and SCARA robots were evaluated based on cost, accuracy, work volume, surface finish, type of profile, and speed. The results showed that the gantry-type robot is the most suitable option, while the cylindrical robot is unsuitable for building construction due to lower accuracy.
- 4 May 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 235 (3) , 660-669
Influence of temperature and volume fraction on the thermophysical properties of CuO-R134a nano refrigerant and its application in battery thermal management system
The battery temperature is one of the important factor that affects the performance of the battery and lifetime. To overcome these issues, the need and usage of an effective battery thermal management system (BTMS) is increased in recent years. The results of BTMS with conventional heat transfer fluids appears in many articles but the very few researchers developed and studied the performance of refrigerant based BTMS. In this research, a novel BTMS is developed and detailed study is conducted to analyze the impact of CuO based refrigerant (R134a) on its performance. Different quantity of CuO nanoparticles mixed with base refrigerant (R134a) and used as a heat transfer fluid. Initially, five different volume proportions (i.e. ɸ – 0.01, 0.02, 0.03, 0.04 and 0.05%) of CuO-R134a nano refrigerants are prepared and the thermophysical properties are studied. The test results reveal that the peak thermal conductivity and viscosity of about 1.28 W/mK and 0.00047 Pa-S is obtained for refrigerant with 0.05 vol.% CuO nanoparticle at 325 K and 300 K respectively. The average cell temperature of about 51 °C, 37 °C, 33 °C and 32 °C is observed for battery without cooling system, BTMS with R134a, 0.01% and 0.05% CuO/R134a respectively. From the results of this study, it can be suggested that the CuO- R134a nano refrigerant will be a promising cooling medium in the battery cooling system.
- 4 May 2021
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 235 (3) , 660-669
Influence of temperature and volume fraction on the thermophysical properties of CuO-R134a nano refrigerant and its application in battery thermal management system
The battery temperature is one of the important factor that affects the performance of the battery and lifetime. To overcome these issues, the need and usage of an effective battery thermal management system (BTMS) is increased in recent years. The results of BTMS with conventional heat transfer fluids appears in many articles but the very few researchers developed and studied the performance of refrigerant based BTMS. In this research, a novel BTMS is developed and detailed study is conducted to analyze the impact of CuO based refrigerant (R134a) on its performance. Different quantity of CuO nanoparticles mixed with base refrigerant (R134a) and used as a heat transfer fluid. Initially, five different volume proportions (i.e. ɸ – 0.01, 0.02, 0.03, 0.04 and 0.05%) of CuO-R134a nano refrigerants are prepared and the thermophysical properties are studied. The test results reveal that the peak thermal conductivity and viscosity of about 1.28 W/mK and 0.00047 Pa-S is obtained for refrigerant with 0.05 vol.% CuO nanoparticle at 325 K and 300 K respectively. The average cell temperature of about 51 °C, 37 °C, 33 °C and 32 °C is observed for battery without cooling system, BTMS with R134a, 0.01% and 0.05% CuO/R134a respectively. From the results of this study, it can be suggested that the CuO- R134a nano refrigerant will be a promising cooling medium in the battery cooling system.
- Open Access
Performance assessment of a solar powered hydrogen production system and its ANFIS model
- Open Access
- 20 August 2018
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 12 (12) , 1375-1381
Experimental investigation of the effects of sonication time and volume concentration on the performance of PVT solar collector
In this research, the effects of sonication time and volume concentration of cupric oxide (CuO)/water nanofluids on the thermal conductivity, viscosity and performance of photovoltaic–thermal (PVT) solar collector are investigated experimentally. Pure water, 0.05, 0.1 and 0.2% volume concentrations of CuO/water nanofluids prepared with 1, 2, 3 and 4 h sonication time are used as the heat transfer fluids in this study. The experimental results show that the thermal conductivity and viscosity of nanofluids are the functions of sonication time and volume concentration and using a 0.2 vol.% nanofluid prepared with 4 h sonication time, the thermal conductivity and viscosity were enhanced up to 3.5 and 7.5%, respectively, with respect to the base fluid, whereas for the same volume concentration and sonication time, the observed thermal and electrical efficiencies of the PVT solar collector are 80.7 and 15.1%, respectively, at 12 noon. It was observed that the highest total efficiency of the PVT solar collector of about 95.8% was obtained for 0.2% CuO/water nanofluid and 4 h sonication time at 12 noon.
- 20 August 2018
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 12 (12) , 1375-1381
Open AccessExperimental investigation of the effects of sonication time and volume concentration on the performance of PVT solar collector
In this research, the effects of sonication time and volume concentration of cupric oxide (CuO)/water nanofluids on the thermal conductivity, viscosity and performance of photovoltaic–thermal (PVT) solar collector are investigated experimentally. Pure water, 0.05, 0.1 and 0.2% volume concentrations of CuO/water nanofluids prepared with 1, 2, 3 and 4 h sonication time are used as the heat transfer fluids in this study. The experimental results show that the thermal conductivity and viscosity of nanofluids are the functions of sonication time and volume concentration and using a 0.2 vol.% nanofluid prepared with 4 h sonication time, the thermal conductivity and viscosity were enhanced up to 3.5 and 7.5%, respectively, with respect to the base fluid, whereas for the same volume concentration and sonication time, the observed thermal and electrical efficiencies of the PVT solar collector are 80.7 and 15.1%, respectively, at 12 noon. It was observed that the highest total efficiency of the PVT solar collector of about 95.8% was obtained for 0.2% CuO/water nanofluid and 4 h sonication time at 12 noon.