Vadym Dmytrovich Chivanov
Research Subjects
Vadym Dmytrovich Chivanov has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
- Oksana Shkromada
Sumy National Agrarian University
7 shared publications - Alina Pikhtirova
Sumy State University
6 shared publications - Viktoriia Ivchenko
Sumy National Agrarian University
6 shared publications - Olha Shvets
Sumy National Agrarian University, Ukraine
5 shared publications - Ольга Георгіївна Бордунова
Sumy National Agrarian University
4 shared publications A N Knysh
3 shared publications
Latest Publications
- Open Access
- 22 March 2026
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 34 (1) , 249-258
THE RESEARCH OF WASTEWATER IMPACT ON CONCRETE STRUCTURES IN THE SEWERAGE SYSTEM OF A PHARMACEUTICAL ENTERPRISE
The relevance of the study is to determine the chemical composition of wastewater and its impact on the technical condition of the sewage system. Aim. The aim of the work was to investigate the chemical composition of wastewater and its effect on reinforced concrete structures of the sewage system. Methods. X-ray diffractometric, colorimetric, fluorimetric, gravimetric, titrimetric. Results. The study of the chemical composition of wastewater showed a shift in pH to the alkaline side, the suspension of dry substances in water was above the norm in the fourth sample by 5.3 %, in the fifth – by 36.3 %; the dry residue in the first sample by 31.3 %, in the second – by 20.2 %, in the third – by 13.9 %, in the fourth – by 9.3 % and in the fifth – by 27.4 %. The content of ammonium nitrogen was higher in the fourth experimental sample by 52.3 %, and in the fifth by 54.1 %. The level of nitrite ions in the first sample was higher by 9.1 %, in the second by 6.0 %, in the third and fifth by 42.4 %, and in the fourth by 36.4 %; the increase in nitrate ions in the first sample was by 11.1 %, in the second by 21.6 %, in the third by 16.0 %, in the fourth by 19.5 %, and in the fifth by 22.4 %. Conclusions. The implemented measures to reduce wastewater pollution were effective and reduced the load on concrete sewage structures. The scientific novelty of the results obtained lies in the field study of wastewater from a settling well of a pharmaceutical enterprise before and after preventive measures.
- 22 March 2026
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 34 (1) , 249-258
Open AccessTHE RESEARCH OF WASTEWATER IMPACT ON CONCRETE STRUCTURES IN THE SEWERAGE SYSTEM OF A PHARMACEUTICAL ENTERPRISE
The relevance of the study is to determine the chemical composition of wastewater and its impact on the technical condition of the sewage system. Aim. The aim of the work was to investigate the chemical composition of wastewater and its effect on reinforced concrete structures of the sewage system. Methods. X-ray diffractometric, colorimetric, fluorimetric, gravimetric, titrimetric. Results. The study of the chemical composition of wastewater showed a shift in pH to the alkaline side, the suspension of dry substances in water was above the norm in the fourth sample by 5.3 %, in the fifth – by 36.3 %; the dry residue in the first sample by 31.3 %, in the second – by 20.2 %, in the third – by 13.9 %, in the fourth – by 9.3 % and in the fifth – by 27.4 %. The content of ammonium nitrogen was higher in the fourth experimental sample by 52.3 %, and in the fifth by 54.1 %. The level of nitrite ions in the first sample was higher by 9.1 %, in the second by 6.0 %, in the third and fifth by 42.4 %, and in the fourth by 36.4 %; the increase in nitrate ions in the first sample was by 11.1 %, in the second by 21.6 %, in the third by 16.0 %, in the fourth by 19.5 %, and in the fifth by 22.4 %. Conclusions. The implemented measures to reduce wastewater pollution were effective and reduced the load on concrete sewage structures. The scientific novelty of the results obtained lies in the field study of wastewater from a settling well of a pharmaceutical enterprise before and after preventive measures.
- 28 September 2025
- Published by Polish Chitin Society in Progress on Chemistry and application of Chitin and its Derivatives
- Vol. 30, 130-142
Characterisation of chitosan and chitosan-based materials by temperature programmed desorption mass spectrometry
The thermal behaviour of chitin, chitosan, and their derivatives is of great importance both for practical applications and for understanding the processes of interaction with additional compounds comprising chitosan-based materials. In this work, the samples of chitin and chitosan obtained in our laboratory from various sources (insects, mushrooms) and commercial samples, as well as derivatives containing iodine, fucorcinum, methylene blue, neomycin, etc., were studied with temperature programmed desorption mass spectrometry. The method reveals the differences in the dehydration of samples. Thermal decomposition in the temperature range from 150 to 200°C is associated with decarboxylation, and above 200°C with decomposition of the main chain. The thermal behaviour of samples depends on the origin of chitin, i.e., the fungal chitin starts to decompose at a lower temperature than insect chitin. The latter one shows thermal behaviour comparable to that of chitin from crustaceans. Chitosan obtained from chitin of various origins is more uniform. The additives in the derivative materials influence the thermal behaviour in different ways, especially a substantial difference was seen in the case of iodine combined with fucorcinum
- 28 September 2025
- Published by Polish Chitin Society in Progress on Chemistry and application of Chitin and its Derivatives
- Vol. 30, 130-142
Characterisation of chitosan and chitosan-based materials by temperature programmed desorption mass spectrometry
The thermal behaviour of chitin, chitosan, and their derivatives is of great importance both for practical applications and for understanding the processes of interaction with additional compounds comprising chitosan-based materials. In this work, the samples of chitin and chitosan obtained in our laboratory from various sources (insects, mushrooms) and commercial samples, as well as derivatives containing iodine, fucorcinum, methylene blue, neomycin, etc., were studied with temperature programmed desorption mass spectrometry. The method reveals the differences in the dehydration of samples. Thermal decomposition in the temperature range from 150 to 200°C is associated with decarboxylation, and above 200°C with decomposition of the main chain. The thermal behaviour of samples depends on the origin of chitin, i.e., the fungal chitin starts to decompose at a lower temperature than insect chitin. The latter one shows thermal behaviour comparable to that of chitin from crustaceans. Chitosan obtained from chitin of various origins is more uniform. The additives in the derivative materials influence the thermal behaviour in different ways, especially a substantial difference was seen in the case of iodine combined with fucorcinum
- Open Access
- 14 July 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (2) , 449-457
ОСОБЛИВОСТІ СТРУКТУРИ ТА ВЛАСТИВОСТЕЙ БЕТОНУ ПРИ ЕКСПЛУАТАЦІЇ В УМОВАХ ВПЛИВУ ОРГАНІЧНОЇ ОЛІЇ
The relevance of the study is to determine the impact of vegetable oil on concrete structures in the case of its long-term action. Currently, the buildings of the agro-industrial complex, built in the 70s and 80s of the 20th century, are used to process sunflower seeds into oil. Aim. To determine the effect of vegetable oil on the physicochemical characteristics of concrete. Methods. The strength of concrete samples was determined by destructive testing depending on the depth of oil penetration; structural changes in concrete were determined by scanning electron microscopy; thermal analysis of concrete samples was performed by thermo-programmed mass spectrometry. Results. It was found that sample №1 was 17 % oiled, with a strength loss of 6 %. Concrete sample №2, with 56 % oiled, lost 19 % of its strength. Sample №3, with 100 % oiled, lost 48 % of its strength. The destruction of the concrete structure was established by electron microscopy. Spores and hyphae of microscopic fungi were detected at a depth of 2 cm from the surface. The study of concrete samples using TPD MS showed that carbon monoxide was intensively released at a temperature of 583 °C from samples 2–0.03 and 3–0.05. CO2 was released at a temperature of 552 °C with an intensity of 0.1 from sample 2 and 0.18 from sample 3. Carbon was not released from the other samples, which is related to the biochemical corrosion of concrete. Water was released from concrete samples 2–0.8 and 3–0.4 at 100 °C. Conclusions. Correlations have been established between the depth of concrete oil impregnation and the loss of strength due to the weakening of contacts between cement stone and aggregate (crushed stone). The scientific novelty of the results obtained lies in determining the long-term impact of organic oil on the physicochemical characteristics of concrete.
- 14 July 2025
- Published by Oles Honchar Dnipropetrovsk National University in Journal of Chemistry and Technologies
- Vol. 33 (2) , 449-457
Open AccessОСОБЛИВОСТІ СТРУКТУРИ ТА ВЛАСТИВОСТЕЙ БЕТОНУ ПРИ ЕКСПЛУАТАЦІЇ В УМОВАХ ВПЛИВУ ОРГАНІЧНОЇ ОЛІЇ
The relevance of the study is to determine the impact of vegetable oil on concrete structures in the case of its long-term action. Currently, the buildings of the agro-industrial complex, built in the 70s and 80s of the 20th century, are used to process sunflower seeds into oil. Aim. To determine the effect of vegetable oil on the physicochemical characteristics of concrete. Methods. The strength of concrete samples was determined by destructive testing depending on the depth of oil penetration; structural changes in concrete were determined by scanning electron microscopy; thermal analysis of concrete samples was performed by thermo-programmed mass spectrometry. Results. It was found that sample №1 was 17 % oiled, with a strength loss of 6 %. Concrete sample №2, with 56 % oiled, lost 19 % of its strength. Sample №3, with 100 % oiled, lost 48 % of its strength. The destruction of the concrete structure was established by electron microscopy. Spores and hyphae of microscopic fungi were detected at a depth of 2 cm from the surface. The study of concrete samples using TPD MS showed that carbon monoxide was intensively released at a temperature of 583 °C from samples 2–0.03 and 3–0.05. CO2 was released at a temperature of 552 °C with an intensity of 0.1 from sample 2 and 0.18 from sample 3. Carbon was not released from the other samples, which is related to the biochemical corrosion of concrete. Water was released from concrete samples 2–0.8 and 3–0.4 at 100 °C. Conclusions. Correlations have been established between the depth of concrete oil impregnation and the loss of strength due to the weakening of contacts between cement stone and aggregate (crushed stone). The scientific novelty of the results obtained lies in determining the long-term impact of organic oil on the physicochemical characteristics of concrete.
- Open Access
- 28 February 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (6 (127)) , 39-46
Determining the characteristics of concrete in a historical building under the influence of climatic and biological factors
The object of this study was concrete samples of the cathedral and wall frescoes. The study solved the problem related to the destruction of concrete and wall frescoes under the long-term influence of biochemical and climatic factors. Samples of concrete for research and wall murals were obtained from a historic listed building. Using microbiological studies and scanning electron microscopy, damage to wall murals and concrete by microscopic fungi was established: Aspergillus fumigatus, Penicillium brevicompactum, Aspergillus niger, Cladosporium sphaerospermum. The study of concrete samples by the TPD-MS method showed the presence of an increased level of moisture and carbon compounds by 20 % in the test samples, compared to control. The sulfur content in all concrete samples was not significant. Determination of the mineral composition of concrete by X-ray diffraction showed the presence of Al2O3, 36–44 %, which indicates a significant clay content. The presence of NiTi, 53 %, and СoMg7O8, 46 %, in the concrete sample indicates the probable migration of the chemical elements of the paint pigments used to decorate the cathedral. The concrete control sample contained a significant amount of SiO2, up to 51 %, which is the main component of sand. A feature of the work is the determination of the corrosion effect on concrete under prolonged exposure to climatic and biological factors. The present study is distinguished by the use of non-destructive methods: microbiological studies, scanning electron microscopy, TPD-MS and X-ray diffraction to determine the destruction of concrete and wall frescoes of the building, which is a cultural heritage. The results of the study could be applied to the development and planning of restoration works for the restoration of buildings that have historical value
- 28 February 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (6 (127)) , 39-46
Open AccessDetermining the characteristics of concrete in a historical building under the influence of climatic and biological factors
The object of this study was concrete samples of the cathedral and wall frescoes. The study solved the problem related to the destruction of concrete and wall frescoes under the long-term influence of biochemical and climatic factors. Samples of concrete for research and wall murals were obtained from a historic listed building. Using microbiological studies and scanning electron microscopy, damage to wall murals and concrete by microscopic fungi was established: Aspergillus fumigatus, Penicillium brevicompactum, Aspergillus niger, Cladosporium sphaerospermum. The study of concrete samples by the TPD-MS method showed the presence of an increased level of moisture and carbon compounds by 20 % in the test samples, compared to control. The sulfur content in all concrete samples was not significant. Determination of the mineral composition of concrete by X-ray diffraction showed the presence of Al2O3, 36–44 %, which indicates a significant clay content. The presence of NiTi, 53 %, and СoMg7O8, 46 %, in the concrete sample indicates the probable migration of the chemical elements of the paint pigments used to decorate the cathedral. The concrete control sample contained a significant amount of SiO2, up to 51 %, which is the main component of sand. A feature of the work is the determination of the corrosion effect on concrete under prolonged exposure to climatic and biological factors. The present study is distinguished by the use of non-destructive methods: microbiological studies, scanning electron microscopy, TPD-MS and X-ray diffraction to determine the destruction of concrete and wall frescoes of the building, which is a cultural heritage. The results of the study could be applied to the development and planning of restoration works for the restoration of buildings that have historical value
- 30 September 2023
- Published by Polish Chitin Society in Progress on Chemistry and application of Chitin and its Derivatives
- Vol. 28, 160-165
PREPARATION AND PHYSICOCHEMICAL CHARACTERISTICS OF AN IODINE AND BISMUTH CONTAINING COMPOSITE MATERIAL BASED ON CHITOSAN
We created composite materials by using a straightforward method, combining chitosan, iodine, and bismuth. We used two chitosan with two different molecular masses. We used iodine in the composites as chitosan iodide and bismuth in the form of tetraiodobismuthanuide. We analysed the resulting materials with scanning electron microscopy, X-ray diffraction, temperature-programmed desorption mass spectrometry, and visible light spectroscopy. We observed that bismuth and iodine were evenly distributed throughout the composites and did not separate into distinct phases. These composite materials have the ability to form organised porous sponges, making them suitable for a wide range of applications in different fields.
- 30 September 2023
- Published by Polish Chitin Society in Progress on Chemistry and application of Chitin and its Derivatives
- Vol. 28, 160-165
PREPARATION AND PHYSICOCHEMICAL CHARACTERISTICS OF AN IODINE AND BISMUTH CONTAINING COMPOSITE MATERIAL BASED ON CHITOSAN
We created composite materials by using a straightforward method, combining chitosan, iodine, and bismuth. We used two chitosan with two different molecular masses. We used iodine in the composites as chitosan iodide and bismuth in the form of tetraiodobismuthanuide. We analysed the resulting materials with scanning electron microscopy, X-ray diffraction, temperature-programmed desorption mass spectrometry, and visible light spectroscopy. We observed that bismuth and iodine were evenly distributed throughout the composites and did not separate into distinct phases. These composite materials have the ability to form organised porous sponges, making them suitable for a wide range of applications in different fields.
- Open Access
- 31 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (120)) , 42-50
Determining changes in the mineral composition of concrete due to chemical corrosion in a sulfate environment
The object of this study was the concrete structures of a chemical enterprise for the production of titanium dioxide. In this case, the ore is decomposed with sulfate acid according to the sulfate production technology. In an aggressive environment, chemical corrosion of concrete occurs, prolonged over time. Using X-ray diffraction and X-ray fluorescence analysis methods, the mineral composition of two prototypes of concrete was determined. It was found that the sample obtained from the workshop for processing ore with sulfate acid showed an increased content of sulfur oxide (SO2) on the surface, by 33 %, with a reduced content of carbonates (CaCO3) on the surface, by 52.9 %, at a depth of 2 cm – by 53.65, compared to another (control) sample. At the same time, iron oxide (Fe2O3) was found on the surface in a sample of concrete from the ore storage room (control), the content of which decreased by 10.4 % at a depth of 2 cm, and by 12.4 % at a depth of 4 cm. The results of electron microscopy show sulfur crystals on the surface of a concrete sample. It was also found that the microstructure of concrete was changed under the influence of sulfate corrosion, depending on the intensity of the exposure to a depth of 2 to 4 cm. By the method of thermoprogrammed mass spectrometry, it was established that when a sample of concrete exposed to sulfate acid is heated to a temperature of 400 °C, sulfur dioxide SO2 is released mainly from the surface. From the surface of the control sample, which contains a significant amount of CaCO3, which is easily destroyed by sulfate acid, there is probably a smaller amount of the product of thermal destruction of calcium carbonate carbon dioxide (CO2). The results of the experiment can be used to study the mechanism of development of sulfate corrosion of concrete prolonged over time.
- 31 December 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (6 (120)) , 42-50
Open AccessDetermining changes in the mineral composition of concrete due to chemical corrosion in a sulfate environment
The object of this study was the concrete structures of a chemical enterprise for the production of titanium dioxide. In this case, the ore is decomposed with sulfate acid according to the sulfate production technology. In an aggressive environment, chemical corrosion of concrete occurs, prolonged over time. Using X-ray diffraction and X-ray fluorescence analysis methods, the mineral composition of two prototypes of concrete was determined. It was found that the sample obtained from the workshop for processing ore with sulfate acid showed an increased content of sulfur oxide (SO2) on the surface, by 33 %, with a reduced content of carbonates (CaCO3) on the surface, by 52.9 %, at a depth of 2 cm – by 53.65, compared to another (control) sample. At the same time, iron oxide (Fe2O3) was found on the surface in a sample of concrete from the ore storage room (control), the content of which decreased by 10.4 % at a depth of 2 cm, and by 12.4 % at a depth of 4 cm. The results of electron microscopy show sulfur crystals on the surface of a concrete sample. It was also found that the microstructure of concrete was changed under the influence of sulfate corrosion, depending on the intensity of the exposure to a depth of 2 to 4 cm. By the method of thermoprogrammed mass spectrometry, it was established that when a sample of concrete exposed to sulfate acid is heated to a temperature of 400 °C, sulfur dioxide SO2 is released mainly from the surface. From the surface of the control sample, which contains a significant amount of CaCO3, which is easily destroyed by sulfate acid, there is probably a smaller amount of the product of thermal destruction of calcium carbonate carbon dioxide (CO2). The results of the experiment can be used to study the mechanism of development of sulfate corrosion of concrete prolonged over time.
- Open Access
- 31 August 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (6(118)) , 57-66
Reducing the biogenic corrosion of concrete in a pigsty by using disinfectants
The object of this study is the regularity of changes in the biogenic destructive effect of microorganisms on the concrete structural elements of livestock facilities due to the use of the original liquid phase mixture of disinfectant based on aldehyde and surfactant. Microorganisms use construction materials as a substrate for growth and nutrition; they produce citric acid, which leads to a change in the composition and morphology of hydrated cement new formations. The composition of the microflora of the pigsty has been determined, and the minimum concentration of disinfectant based on glutaraldehyde and didecyl dimethyl ammonium chloride was found. By the TPD MS method, a decrease in the intensity of carbon dioxide (CO2) release in concrete samples during the heating of the sample to 900 °C was proved, compared to the control intact corrosion sample. Electron microscopy of concrete samples shows the presence of destructive changes and colonies of micromycetes. It was established that calcite was intensively released in the control sample of concrete, which retained its integrity and was not subjected to corrosion when heated to a temperature of 600 °C. Electron microscopy confirms the preservation of the homogeneous structure of concrete. The use of a disinfectant based on glutaraldehyde and didecyl dimethyl ammonium chloride at a concentration of 1 % destroys colonies of micromycetes, 2 % – the shell of microorganisms, and 3 % – biofilm. Treatment of concrete with a disinfectant at a concentration of 3 % destroys microorganisms Aspergillus fumigatus and Penicillium oxalicum, inhibits the process of biological corrosion of concrete, and strengthens the structure of concrete. The results of the experiment can be applied to inhibit the corrosion of concrete and extend the life of building structures made of concrete through the use of a disinfectant based on aldehyde and didecyl dimethyl ammonium chloride at a concentration of 3 %.
- 31 August 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 4 (6(118)) , 57-66
Open AccessReducing the biogenic corrosion of concrete in a pigsty by using disinfectants
The object of this study is the regularity of changes in the biogenic destructive effect of microorganisms on the concrete structural elements of livestock facilities due to the use of the original liquid phase mixture of disinfectant based on aldehyde and surfactant. Microorganisms use construction materials as a substrate for growth and nutrition; they produce citric acid, which leads to a change in the composition and morphology of hydrated cement new formations. The composition of the microflora of the pigsty has been determined, and the minimum concentration of disinfectant based on glutaraldehyde and didecyl dimethyl ammonium chloride was found. By the TPD MS method, a decrease in the intensity of carbon dioxide (CO2) release in concrete samples during the heating of the sample to 900 °C was proved, compared to the control intact corrosion sample. Electron microscopy of concrete samples shows the presence of destructive changes and colonies of micromycetes. It was established that calcite was intensively released in the control sample of concrete, which retained its integrity and was not subjected to corrosion when heated to a temperature of 600 °C. Electron microscopy confirms the preservation of the homogeneous structure of concrete. The use of a disinfectant based on glutaraldehyde and didecyl dimethyl ammonium chloride at a concentration of 1 % destroys colonies of micromycetes, 2 % – the shell of microorganisms, and 3 % – biofilm. Treatment of concrete with a disinfectant at a concentration of 3 % destroys microorganisms Aspergillus fumigatus and Penicillium oxalicum, inhibits the process of biological corrosion of concrete, and strengthens the structure of concrete. The results of the experiment can be applied to inhibit the corrosion of concrete and extend the life of building structures made of concrete through the use of a disinfectant based on aldehyde and didecyl dimethyl ammonium chloride at a concentration of 3 %.
- Open Access
- 30 July 2022
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 4,p. 114-126
Detection of the synergetic influence of chemical and microbiological factors on the properties of concrete constructions at chemical plants during the long-term service
Long-term operation of reinforced concrete structures in the conditions of chemical enterprises has a powerful negative impact on the physical and chemical properties of concrete, which leads to its destruction. The aim of this research is to determine the effect of biological and chemical corrosion on concrete structures in the workshop for the production of titanium dioxide by the sulphate method and the storage of finished products. In particular, chemical production for the synthesis of titanium dioxide by the sulfate method causes the rapid course of chemical (acid and sulfate) and microbiological (thionic bacteria and microscopic fungi) corrosion processes. These corrosion processes reinforce each other according to a synergistic principle. As a result, temperature-programmed desorption mass spectrometry (TPD MS) and scanning electron microscopy have experimentally proven the presence and spatial localization of colonies of thionic bacteria and microscopic fungi in concrete structures. Correlations between the intensity of biochemical corrosion and the depth of damage to the microstructures of concrete structures have been established. Moreover, a change in the chemical composition of concrete in the workshop for the production of titanium dioxide (increased SO2 content and reduced CO2) and the formation of gypsum crystals (CaSO4 2H2O) as a result of the dissimilation of microorganisms was established. Also, in the storage room for finished products, calcium citrate crystals and a violation of the formation of calcium carbonate are formed in the surface layers of concrete. In addition, the results of the study can be used to develop antimicrobial and anticorrosive protective agents to stop the biochemical corrosion of concrete in a chemical plant
- 30 July 2022
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 4,p. 114-126
Open AccessDetection of the synergetic influence of chemical and microbiological factors on the properties of concrete constructions at chemical plants during the long-term service
Long-term operation of reinforced concrete structures in the conditions of chemical enterprises has a powerful negative impact on the physical and chemical properties of concrete, which leads to its destruction. The aim of this research is to determine the effect of biological and chemical corrosion on concrete structures in the workshop for the production of titanium dioxide by the sulphate method and the storage of finished products. In particular, chemical production for the synthesis of titanium dioxide by the sulfate method causes the rapid course of chemical (acid and sulfate) and microbiological (thionic bacteria and microscopic fungi) corrosion processes. These corrosion processes reinforce each other according to a synergistic principle. As a result, temperature-programmed desorption mass spectrometry (TPD MS) and scanning electron microscopy have experimentally proven the presence and spatial localization of colonies of thionic bacteria and microscopic fungi in concrete structures. Correlations between the intensity of biochemical corrosion and the depth of damage to the microstructures of concrete structures have been established. Moreover, a change in the chemical composition of concrete in the workshop for the production of titanium dioxide (increased SO2 content and reduced CO2) and the formation of gypsum crystals (CaSO4 2H2O) as a result of the dissimilation of microorganisms was established. Also, in the storage room for finished products, calcium citrate crystals and a violation of the formation of calcium carbonate are formed in the surface layers of concrete. In addition, the results of the study can be used to develop antimicrobial and anticorrosive protective agents to stop the biochemical corrosion of concrete in a chemical plant
- Open Access
- 30 August 2021
- Published by Publishing House Helvetica (Publications) in Bulletin of Sumy National Agrarian University. The series: Livestock
- No. 3 (46),p. 95-99
БІОМІМЕТИЧНА ТЕХНОЛОГІЯ ПЕРЕДІНКУБАЦІЙНОЇ ОБРОБКИ ЯЄЦЬ КУРЕЙ «ШТУЧНА КУТИКУЛА» «GREEN ARTICLE» TIO2 FE2O3
В роботі представлені докладні відомості про розроблені авторами біоміметичні технології захисту інкубаційних яєць курей, що складається з композиту хітозану, перекисних сполук і фотокаталітичних ультрадисперсних частинок діоксиду титану TiO2 і жовтого залізоокисного пігменту заліза Fe2O3. Розроблені теоретичні та прикладні аспекти концепції використання біоміметичних захисних покриттів «GREEN ARTICLE» («ARTIficial cutiCLE») у птахівничій галузі, а саме у виробництві інкубаційних яєць. Базовою матричною складовою захисних покрить «GREEN ARTICLE» є «зеле-ний», екологічно-безпечний, широко розповсюджений та недорогий і нешкідливий у виробництві матеріал - хітозан. Екс-периментально доведено, що електрохімічна та ультразвукова технології модифікації розчину хітозану у перекисних сполуках (надоцтова кислота, перекис водню) наночастками оксидів: титану, заліза, та металів: титану, міді, а також кальциту, дозволяє створити захисні покриття «подвійної дії» відповідно до технології попередження контамінації інку-баційних яєць патогенною мікрофлорою, підвищення показників виводимості яєць та якості молодняку «GREEN ARTICLE». Результати інкубації протягом 21 доби показали, що виводимість яєць курей Хайсекс Браун між контрольною та дослідною групами відрізнялася на 4,7%. Так, у контрольній групі, цей показник становить 85,0%, а в досліді складає 89,7%. Показник інкубації у курей кросу Хайсекс Уайт покращився на 5,3%. У контрольній групі цей показник становить 84,9% та у дослідній групі де яйця обробляли розчином TiO2 Fe2O3 90,2%. Також композиція позитивно впливає на знижен-ня контамінації патогенної мікрофлори на поверхні шкаралупи курячих яєць до 0,4-0,71% від вихідної кількості бактеріа-льних колоній протягом 19 днів.
- 30 August 2021
- Published by Publishing House Helvetica (Publications) in Bulletin of Sumy National Agrarian University. The series: Livestock
- No. 3 (46),p. 95-99
Open AccessБІОМІМЕТИЧНА ТЕХНОЛОГІЯ ПЕРЕДІНКУБАЦІЙНОЇ ОБРОБКИ ЯЄЦЬ КУРЕЙ «ШТУЧНА КУТИКУЛА» «GREEN ARTICLE» TIO2 FE2O3
В роботі представлені докладні відомості про розроблені авторами біоміметичні технології захисту інкубаційних яєць курей, що складається з композиту хітозану, перекисних сполук і фотокаталітичних ультрадисперсних частинок діоксиду титану TiO2 і жовтого залізоокисного пігменту заліза Fe2O3. Розроблені теоретичні та прикладні аспекти концепції використання біоміметичних захисних покриттів «GREEN ARTICLE» («ARTIficial cutiCLE») у птахівничій галузі, а саме у виробництві інкубаційних яєць. Базовою матричною складовою захисних покрить «GREEN ARTICLE» є «зеле-ний», екологічно-безпечний, широко розповсюджений та недорогий і нешкідливий у виробництві матеріал - хітозан. Екс-периментально доведено, що електрохімічна та ультразвукова технології модифікації розчину хітозану у перекисних сполуках (надоцтова кислота, перекис водню) наночастками оксидів: титану, заліза, та металів: титану, міді, а також кальциту, дозволяє створити захисні покриття «подвійної дії» відповідно до технології попередження контамінації інку-баційних яєць патогенною мікрофлорою, підвищення показників виводимості яєць та якості молодняку «GREEN ARTICLE». Результати інкубації протягом 21 доби показали, що виводимість яєць курей Хайсекс Браун між контрольною та дослідною групами відрізнялася на 4,7%. Так, у контрольній групі, цей показник становить 85,0%, а в досліді складає 89,7%. Показник інкубації у курей кросу Хайсекс Уайт покращився на 5,3%. У контрольній групі цей показник становить 84,9% та у дослідній групі де яйця обробляли розчином TiO2 Fe2O3 90,2%. Також композиція позитивно впливає на знижен-ня контамінації патогенної мікрофлори на поверхні шкаралупи курячих яєць до 0,4-0,71% від вихідної кількості бактеріа-льних колоній протягом 19 днів.
- Open Access
- 12 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (110)) , 52-60
Defining patterns in the influence exerted by the interelated biochemical corrosion on concrete building structures under the conditions of a chemical enterprise
The effect of microbial and chemical corrosion on concrete structures operated in the conditions of chemical enterprises has been established that makes it possible to reliably predict the timing of their decommissioning in order to prevent industrial disasters. Even though the construction complies with all building codes, concrete structures eventually undergo chemical and biological corrosion. The innovation proposed in this study implies investigating the depth and degree of damage to concrete at the microscopic level by the method of raster electron microscopy. In addition, the TPD-MS method has been suggested for determining the quantitative and qualitative state of the carbonate components of concrete and sulfur compounds. This study has found that in concrete samples from the titanium dioxide production plant, the amount of carbon dioxide release is twice less than in control samples at t=600 °C while the level of sulfur dioxide, on the contrary, increases. This is due to the ability of thionic bacteria to accumulate sulfate acid that destroys the cementing component in concrete. The reported results confirm the impact of products of the activity of Acidithiobacillus thiooxidans microorganisms on corrosion processes in concrete. In addition, when using the TPD-MS method, it was established in the storage room of the finished product that heating the control sample of concrete leads to a release of the significant amount of СО2 at t=580–600 °C. However, the experimental samples of concrete are almost lacking carbon compounds because the acid metabolites of microfungi interfere with its formation. Microscopic and REM studies revealed the localization of Acidithiobacillus thiooxidans and Aspergillus fumigatus in concrete. This study has established patterns related to the mechanism that forms chemical compounds in concrete and the metabolism of microorganisms
- 12 April 2021
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 2 (6 (110)) , 52-60
Open AccessDefining patterns in the influence exerted by the interelated biochemical corrosion on concrete building structures under the conditions of a chemical enterprise
The effect of microbial and chemical corrosion on concrete structures operated in the conditions of chemical enterprises has been established that makes it possible to reliably predict the timing of their decommissioning in order to prevent industrial disasters. Even though the construction complies with all building codes, concrete structures eventually undergo chemical and biological corrosion. The innovation proposed in this study implies investigating the depth and degree of damage to concrete at the microscopic level by the method of raster electron microscopy. In addition, the TPD-MS method has been suggested for determining the quantitative and qualitative state of the carbonate components of concrete and sulfur compounds. This study has found that in concrete samples from the titanium dioxide production plant, the amount of carbon dioxide release is twice less than in control samples at t=600 °C while the level of sulfur dioxide, on the contrary, increases. This is due to the ability of thionic bacteria to accumulate sulfate acid that destroys the cementing component in concrete. The reported results confirm the impact of products of the activity of Acidithiobacillus thiooxidans microorganisms on corrosion processes in concrete. In addition, when using the TPD-MS method, it was established in the storage room of the finished product that heating the control sample of concrete leads to a release of the significant amount of СО2 at t=580–600 °C. However, the experimental samples of concrete are almost lacking carbon compounds because the acid metabolites of microfungi interfere with its formation. Microscopic and REM studies revealed the localization of Acidithiobacillus thiooxidans and Aspergillus fumigatus in concrete. This study has established patterns related to the mechanism that forms chemical compounds in concrete and the metabolism of microorganisms