Jacek Leyko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jacek Leyko has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Damian Batory
Department of Vehicles and Fundamentals of Machine Design, Lodz University of Technology, 1/15 Stefanowskiego St., 90-924 Lodz, Poland
4 shared publications - Grzegorz Mitukiewicz
Department of Vehicles and Fundamentals of Machine Design, Lodz University of Technology, Stefanowskiego Street 1/15, 90537 Lodz, Poland
4 shared publications - Jarosław Goszczak
Lodz University of Technology
2 shared publications A. Kedziora
Institute of General and Ecological Chemistry, Lodz University of Technology, Lodz, Poland
1 shared publication- Agnieszka Czylkowska
Lodz University of Technology
1 shared publication Cezary Kuzalski
1 shared publication
Latest Publications
- Open Access
Study on SI Engine Operation Stability at Lean Condition—The Effect of a Small Amount of Hydrogen Addition
The lean-burn mode is a solution that reduces the fuel consumption of spark-ignition internal combustion engines and keeps the low exhaust emission, but the stability of the lean-burn combustion process, especially at low loads, needs to be addressed. Enhancing gasoline with hybrid hydrogen oxygen (HHO) gas—a mixture of hydrogen and oxygen gases—is proposed to improve combustion of the lean-gasoline mixture. A three-cylinder, spark-ignition, naturally aspirated, MPI engine with HHO gas produced with an alkaline water electrolyzer and introduced as a gasoline enhancement was tested. The amount of hydrogen added to the lean-gasoline mixture (λ = 1.4) was in the range from 0.15 to 1.5%, and the results were compared to the stoichiometric (λ = 1) and pure lean mode (λ = 1.4) gasoline operation. The other authors’ results show that a minimum 3% of the mass fraction of hydrogen is necessary to affect the gasoline combustion process. This paper proved that even a small hydrogen enhancement of gasoline in the amount of 0.3% of the mass fraction improves the combustion stability.
Open AccessStudy on SI Engine Operation Stability at Lean Condition—The Effect of a Small Amount of Hydrogen Addition
The lean-burn mode is a solution that reduces the fuel consumption of spark-ignition internal combustion engines and keeps the low exhaust emission, but the stability of the lean-burn combustion process, especially at low loads, needs to be addressed. Enhancing gasoline with hybrid hydrogen oxygen (HHO) gas—a mixture of hydrogen and oxygen gases—is proposed to improve combustion of the lean-gasoline mixture. A three-cylinder, spark-ignition, naturally aspirated, MPI engine with HHO gas produced with an alkaline water electrolyzer and introduced as a gasoline enhancement was tested. The amount of hydrogen added to the lean-gasoline mixture (λ = 1.4) was in the range from 0.15 to 1.5%, and the results were compared to the stoichiometric (λ = 1) and pure lean mode (λ = 1.4) gasoline operation. The other authors’ results show that a minimum 3% of the mass fraction of hydrogen is necessary to affect the gasoline combustion process. This paper proved that even a small hydrogen enhancement of gasoline in the amount of 0.3% of the mass fraction improves the combustion stability.
- Open Access
- 22 February 2023
- Published by Polish Academy of Sciences Chancellery in Metrology and Measurement Systems
- Vol. 30 (2) , 367-376
An experimental device for evaluation of hydrogen sorption
Hydrogen storage for the purposes of the automotive industry in a form other than under high pressure or cryo conditions has been under careful investigation by researchers over past decades. One of the arising methods is the usage of powdered/granulated beds that contain metal hydrides and/or carbon materials to take advantage of the "spillover" phenomenon. Handling and characterization of such material can be troublesome, which is why the experimental setup needs careful investigation. The apparatus for the analysis of hydrogen sorption/desorption characteristics has been successfully designed and described based on the constructed unit within the scope of this article. The full functionality of that setup covered fuelling the bed as well as the examination of sorption/desorption potential. Moreover, the proposed experimental device can clarify many uncertainties about further development and optimization of hydrogen storage materials.
- 22 February 2023
- Published by Polish Academy of Sciences Chancellery in Metrology and Measurement Systems
- Vol. 30 (2) , 367-376
Open AccessAn experimental device for evaluation of hydrogen sorption
Hydrogen storage for the purposes of the automotive industry in a form other than under high pressure or cryo conditions has been under careful investigation by researchers over past decades. One of the arising methods is the usage of powdered/granulated beds that contain metal hydrides and/or carbon materials to take advantage of the "spillover" phenomenon. Handling and characterization of such material can be troublesome, which is why the experimental setup needs careful investigation. The apparatus for the analysis of hydrogen sorption/desorption characteristics has been successfully designed and described based on the constructed unit within the scope of this article. The full functionality of that setup covered fuelling the bed as well as the examination of sorption/desorption potential. Moreover, the proposed experimental device can clarify many uncertainties about further development and optimization of hydrogen storage materials.
- Open Access
- 12 April 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (8) , 3900
Experimental Study of Drag Torque between Wet Clutch Discs
The development of automatic gearbox control systems contributes to their increasing popularity. By raising the number of gears and sophisticated algorithms, the reduction of fuel consumption is feasible regarding traditional manual transmissions. The continuously variable transmissions (CVT) are also growing their share of the market. Wet clutches are employed in all types of automatic transmissions, but because of oil viscosity, when such a type of clutch is disengaged, the drag torque phenomenon occurs. This deteriorates the global efficiency of the transmission system. To recognize the nature of this drag torque and how it is influenced by the main parameters (distance between plates, value of oil flow rate lubricating clutch, oil temperature, rotational speed between plates), a new test stand has been designed and assembled. The value of rotational speed has been studied up to 7000 rpm which is novel in literature. Due to strongly nonlinear dependences, the achieved results can contribute to designing more efficient clutch systems due to the strongly nonlinear nature of observed phenomena.
- 12 April 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (8) , 3900
Open AccessExperimental Study of Drag Torque between Wet Clutch Discs
The development of automatic gearbox control systems contributes to their increasing popularity. By raising the number of gears and sophisticated algorithms, the reduction of fuel consumption is feasible regarding traditional manual transmissions. The continuously variable transmissions (CVT) are also growing their share of the market. Wet clutches are employed in all types of automatic transmissions, but because of oil viscosity, when such a type of clutch is disengaged, the drag torque phenomenon occurs. This deteriorates the global efficiency of the transmission system. To recognize the nature of this drag torque and how it is influenced by the main parameters (distance between plates, value of oil flow rate lubricating clutch, oil temperature, rotational speed between plates), a new test stand has been designed and assembled. The value of rotational speed has been studied up to 7000 rpm which is novel in literature. Due to strongly nonlinear dependences, the achieved results can contribute to designing more efficient clutch systems due to the strongly nonlinear nature of observed phenomena.
- Open Access
- 8 November 2021
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 134 (2) , 1089
Correction to: Steam reforming of ethanol for hydrogen production: influence of catalyst composition (Ni/Al2O3, Ni/Al2O3–CeO2, Ni/Al2O3–ZnO) and process conditions
- 8 November 2021
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 134 (2) , 1089
Open AccessCorrection to: Steam reforming of ethanol for hydrogen production: influence of catalyst composition (Ni/Al2O3, Ni/Al2O3–CeO2, Ni/Al2O3–ZnO) and process conditions
- Open Access
- 1 June 2021
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 15 (2) , 156-168
Analysis of the Cruciform Sample Shapes for Bi-Axial Tensile Tests Based on the Geometries Currently Presented in the Literature
The paper contributes to the global research of the best shape of cruciform samples for biaxial tensile tests. Based on literature research, one of the proposed samples’ shape comparison methodology was employed to achieve the ultimate results. A variety of specimens with different shapes were...
- 1 June 2021
- Published by Wydawnictwo Naukowe Gabriel Borowski (WNGB) in Advances in Science and Technology Research Journal
- Vol. 15 (2) , 156-168
Open AccessAnalysis of the Cruciform Sample Shapes for Bi-Axial Tensile Tests Based on the Geometries Currently Presented in the Literature
The paper contributes to the global research of the best shape of cruciform samples for biaxial tensile tests. Based on literature research, one of the proposed samples’ shape comparison methodology was employed to achieve the ultimate results. A variety of specimens with different shapes were...