R. V. Iskhakov
Research Subjects
R. V. Iskhakov has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
A S Budnikov
Department of Metal Forming, National University of Science and Technology 'MISIS' (NUST 'MISIS'), 4, Leninskiy prospect, Moscow, 119049, Russia
1 shared publication- Alexander S. Aleshchenko
National University of Science and Technology MISiS, Moscow, Russian Federation
1 shared publication - Boris Alekseevich Romantsev
Baikov Institute of Metallurgy and Materials Science, Moscow, RUSSIAN FEDERATION
1 shared publication M V Kadach
Department of Metal Forming, National University of Science and Technology 'MISIS' (NUST 'MISIS'), 4, Leninskiy prospect, Moscow, 119049, Russia
1 shared publication- Sergei Pavlovich Galkin
University of Science and Technology MISIS, Moscow, Russian Federation
1 shared publication Yu V Gamin
Department of Metal Forming, National University of Science and Technology 'MISIS' (NUST 'MISIS'), 4, Leninskiy prospect, Moscow, 119049, Russia
1 shared publication
Latest Publications
- 10 May 2021
- Published by Springer Nature in Metallurgist
- Vol. 65 (1-2) , 185-195
Effect of Preliminary Deformation of Continuously Cast Billets by Radial-Shear Rolling on the Structure and Properties of Hot-Rolled Chromium-Containing Steel Pipes
- 10 May 2021
- Published by Springer Nature in Metallurgist
- Vol. 65 (1-2) , 185-195
Effect of Preliminary Deformation of Continuously Cast Billets by Radial-Shear Rolling on the Structure and Properties of Hot-Rolled Chromium-Containing Steel Pipes
- Open Access
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 966 (1) , 012074
Development of radial-shear rolling mill special stands for continuous cast billets deformation
The article offers the structure of the three-roll stand for radial-shear rolling that is designed to deformation of continuous cast billets. The stand can be installed in the pipe rolling mill manufacturing line that shall ensure manufacturing flexibility. To achieve the objective set, elaboration of working rolls integration with the drive as well as verification against the allowable torque and strength calculations in SolidWorks Simulation were performed at the design stage. For the major part of the frame, stresses do not exceed 60 MPa and the design rigidity rate will be 2.86 MN/mm. The special stand has a specific frame structure to ensure its mounting on the existing equipment base. The configuration of rolls sets is selected considering the possibility of integration with the spindle assemblies of the group drive and maximum allowable cross angle (≤ 15°). The developed design proves to have sufficient strength margin with the relatively small weight. The special radial-shear rolling mill stand will allow increasing total strain degree and reducing the number of billets sizes.
- 1 November 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 966 (1) , 012074
Open AccessDevelopment of radial-shear rolling mill special stands for continuous cast billets deformation
The article offers the structure of the three-roll stand for radial-shear rolling that is designed to deformation of continuous cast billets. The stand can be installed in the pipe rolling mill manufacturing line that shall ensure manufacturing flexibility. To achieve the objective set, elaboration of working rolls integration with the drive as well as verification against the allowable torque and strength calculations in SolidWorks Simulation were performed at the design stage. For the major part of the frame, stresses do not exceed 60 MPa and the design rigidity rate will be 2.86 MN/mm. The special stand has a specific frame structure to ensure its mounting on the existing equipment base. The configuration of rolls sets is selected considering the possibility of integration with the spindle assemblies of the group drive and maximum allowable cross angle (≤ 15°). The developed design proves to have sufficient strength margin with the relatively small weight. The special radial-shear rolling mill stand will allow increasing total strain degree and reducing the number of billets sizes.