Alton Reich
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Alton Reich has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Keith Williams
University of Alabama, Tuscaloosa, AL
3 shared publicationsSteve Doherty
Streamline Automation, LLC, Huntsville, AL
3 shared publicationsJames Shaw
Streamline Automation, LLC, Huntsville, AL
2 shared publicationsJohn Charest
Construction Solutions Inc., Amesbury, MA
2 shared publicationsRoberto Di Salvo
Streamline Automation, LLC, Huntsville, AL
2 shared publicationsAlex DiMeo
Curtiss-Wright Flow Control, East Farmingdale, NY
1 shared publication
Latest Publications
- 14 July 2019
- Published by ASME International
Use of CFD to Improve Control Valve Effectiveness
Control valves are used to adjust fluid flow rates in an extremely wide variety of applications. This paper discusses a steam flow control valve that is required to operate with a fairly wide range of inlet conditions (steam pressure) and provide effective control over a fairly wide range of steam flow rates. In this particular case a valve design was developed using “classical” methods — a combination of experience and hand calculations. The valve was tested and it did not provide adequate control over the flow for the application. The valve redesign effort used CFD to gain insight into the flow through the valve in order to evaluate control performance before the valve was fabricated and assembled. Several internal geometries were assessed and compared in order to identify two configurations that would meet the flow control requirements. These configurations were fabricated and tested and deemed to be adequate.
- 14 July 2019
- Published by ASME International
Use of CFD to Improve Control Valve Effectiveness
Control valves are used to adjust fluid flow rates in an extremely wide variety of applications. This paper discusses a steam flow control valve that is required to operate with a fairly wide range of inlet conditions (steam pressure) and provide effective control over a fairly wide range of steam flow rates. In this particular case a valve design was developed using “classical” methods — a combination of experience and hand calculations. The valve was tested and it did not provide adequate control over the flow for the application. The valve redesign effort used CFD to gain insight into the flow through the valve in order to evaluate control performance before the valve was fabricated and assembled. Several internal geometries were assessed and compared in order to identify two configurations that would meet the flow control requirements. These configurations were fabricated and tested and deemed to be adequate.
- 14 July 2019
- Published by ASME International
Testing of a Non-Cylindrical Vacuum Vessel
Most vacuum vessels are bodies of revolution that are cylindrical or spherical. A square vacuum vessel was developed for a specialized application that needed to be suitable for repeated, rapid sealing and unsealing, and operation at mild vacuum (∼0.5 bara). This paper discusses the challenges that we faced in fabrication and testing of the vacuum vessel. The vacuum vessel was initially tested in a test rig. A second set of challenges was encountered when the vessel was tested mounted in the system. It captures the lessons learned from fabrication, rework, and modifications that were necessary to get the vessel to pass leakage testing.
- 14 July 2019
- Published by ASME International
Testing of a Non-Cylindrical Vacuum Vessel
Most vacuum vessels are bodies of revolution that are cylindrical or spherical. A square vacuum vessel was developed for a specialized application that needed to be suitable for repeated, rapid sealing and unsealing, and operation at mild vacuum (∼0.5 bara). This paper discusses the challenges that we faced in fabrication and testing of the vacuum vessel. The vacuum vessel was initially tested in a test rig. A second set of challenges was encountered when the vessel was tested mounted in the system. It captures the lessons learned from fabrication, rework, and modifications that were necessary to get the vessel to pass leakage testing.
- 15 July 2018
- Published by ASME International
System and Solenoid Valve Interaction Leading to Spurious Opening
In a pressurized water reactor the high pressure system vent lines from the pressurizer and reactor are routed to a common header that can be emptied to the refueling water storage tank or a drain tank. During plant testing the valves are operated in the following sequence: the pressurizer isolation valve is opened to pressurize the common header, the pressurizer isolation valve is closed, then the drain tank isolation valve is opened. This sequence of valve operation verifies that the valves open and close properly — opening the pressurizer isolation valve allows steam to enter the common header and is verified by pressure indication via a pressure transducer, and opening the drain tank isolation valve decreases the pressure in the common header and verifies that the pressurizer isolation valve closed properly. During this sequence of valve actuation, the other solenoid valves in the system are subject to transient steam pressures. During one test sequence an isolation valve to the refueling water storage tank indicated that it was not closed for a period of several seconds. Since there is only one pressure transducer in the common header, a systemlevel analysis was performed to obtain a more detailed understanding of the transient pressures in the common header, and how that might affect solenoid valve performance.
- 15 July 2018
- Published by ASME International
System and Solenoid Valve Interaction Leading to Spurious Opening
In a pressurized water reactor the high pressure system vent lines from the pressurizer and reactor are routed to a common header that can be emptied to the refueling water storage tank or a drain tank. During plant testing the valves are operated in the following sequence: the pressurizer isolation valve is opened to pressurize the common header, the pressurizer isolation valve is closed, then the drain tank isolation valve is opened. This sequence of valve operation verifies that the valves open and close properly — opening the pressurizer isolation valve allows steam to enter the common header and is verified by pressure indication via a pressure transducer, and opening the drain tank isolation valve decreases the pressure in the common header and verifies that the pressurizer isolation valve closed properly. During this sequence of valve actuation, the other solenoid valves in the system are subject to transient steam pressures. During one test sequence an isolation valve to the refueling water storage tank indicated that it was not closed for a period of several seconds. Since there is only one pressure transducer in the common header, a systemlevel analysis was performed to obtain a more detailed understanding of the transient pressures in the common header, and how that might affect solenoid valve performance.
- 16 July 2017
- Published by ASME International
Application of Model-Based Condition Monitoring to the Human Cardiovascular System
The techniques applied by mechanical engineers to problems of machinery condition monitoring can also be applied in other fields. This paper discusses applying techniques that are regularly applied to machinery and system condition monitoring to the human cardiovascular system. Techniques such as physics-based system modeling coupled with limited measurements can be used to infer the condition of a system or specific component. In this case, a mathematical model of the flow through the cardiovascular system was implemented and can be used independently to simulate system performance. Given basic system parameters including heart rate and vascular resistances, the model generates time varying flows and pressures in different portions of the system. The model can be used to interpret a measurement performed on the system to obtain additional information about the state of the system. In this case pulse waveform information is used to make a system flow measurement. This paper will provide an overview of the technique used, the structure of the model, and the initial validation with patient data.
- 16 July 2017
- Published by ASME International
Application of Model-Based Condition Monitoring to the Human Cardiovascular System
The techniques applied by mechanical engineers to problems of machinery condition monitoring can also be applied in other fields. This paper discusses applying techniques that are regularly applied to machinery and system condition monitoring to the human cardiovascular system. Techniques such as physics-based system modeling coupled with limited measurements can be used to infer the condition of a system or specific component. In this case, a mathematical model of the flow through the cardiovascular system was implemented and can be used independently to simulate system performance. Given basic system parameters including heart rate and vascular resistances, the model generates time varying flows and pressures in different portions of the system. The model can be used to interpret a measurement performed on the system to obtain additional information about the state of the system. In this case pulse waveform information is used to make a system flow measurement. This paper will provide an overview of the technique used, the structure of the model, and the initial validation with patient data.
- 17 July 2016
- Published by ASME International
Carbon Fiber Reinforcement of a Water Storage Tank for Beyond Design Basis Loads
The severe damage to the Fukushima nuclear plant occurred as a result of a beyond design basis event. This has prompted a systematic review of safety critical systems at US nuclear power plants to evaluate the existing safety margin based on beyond design basis loads. At one US nuclear power plant it was found that the Refueling Water Storage Tank (RWST) did not have sufficient margin to withstand the defined beyond design basis seismic event. An analysis indicated that the RWST would fail in an elephant foot buckling mode. This paper describes the design and analysis of a Carbon Fiber Reinforced Polymer (CFRP) repair system used to strengthen the RWST to increase the critical buckling stress for the elephant foot buckling mode.
- 17 July 2016
- Published by ASME International
Carbon Fiber Reinforcement of a Water Storage Tank for Beyond Design Basis Loads
The severe damage to the Fukushima nuclear plant occurred as a result of a beyond design basis event. This has prompted a systematic review of safety critical systems at US nuclear power plants to evaluate the existing safety margin based on beyond design basis loads. At one US nuclear power plant it was found that the Refueling Water Storage Tank (RWST) did not have sufficient margin to withstand the defined beyond design basis seismic event. An analysis indicated that the RWST would fail in an elephant foot buckling mode. This paper describes the design and analysis of a Carbon Fiber Reinforced Polymer (CFRP) repair system used to strengthen the RWST to increase the critical buckling stress for the elephant foot buckling mode.
- 17 July 2016
- Published by ASME International
Analysis of Pressure Relief Valve Dynamics During Opening
In nuclear power plants power actuated pressure relief valves serve several purposes. They act as safety valves and open automatically in response to unusually high pressures in the primary system. They also act as power operated valves and are used to relieve steam in response to automatic or manually initiated control signals. These valves are required to lift completely over a short duration from the time that they receive an actuation signal, or the system pressure exceeds the set point. This short lift time results in the valve disk moving at high velocities, and can result in high impact forces on the piston and stem when the valve fully opens. To quantitatively evaluate the dynamic performance of the Target Rocket Pressure Relief Valve, an analysis effort was undertaken which would accommodate both the fluid dynamic features of the valve operation, as well as the kinematic characteristics of the valve, during pressure relief valve operation. To execute the analysis, the Generalized Fluid System Simulation Program (GFSSP) was used. GFSSP is a network flow solver CFD code developed by NASA that has the ability to analyze transient, multi-phase flows, and conjugate heat transfer, along with the inclusion of custom user subroutines developed by the user which can accommodate other simulation requirements. In this paper we present the GFSSP model developed, and the computed results that could be compared with corresponding parameters as measured from experimental testing for the pressure relief valve. Adjustments to GFSSP input parameters allow the anchoring of the GFSSP valve model to test data. This makes it possible to use the GFSSP model as a predictive tool for understanding valve dynamics, as well as evaluating proposed pressure relief valve modifications for performance improvements.
- 17 July 2016
- Published by ASME International
Analysis of Pressure Relief Valve Dynamics During Opening
In nuclear power plants power actuated pressure relief valves serve several purposes. They act as safety valves and open automatically in response to unusually high pressures in the primary system. They also act as power operated valves and are used to relieve steam in response to automatic or manually initiated control signals. These valves are required to lift completely over a short duration from the time that they receive an actuation signal, or the system pressure exceeds the set point. This short lift time results in the valve disk moving at high velocities, and can result in high impact forces on the piston and stem when the valve fully opens. To quantitatively evaluate the dynamic performance of the Target Rocket Pressure Relief Valve, an analysis effort was undertaken which would accommodate both the fluid dynamic features of the valve operation, as well as the kinematic characteristics of the valve, during pressure relief valve operation. To execute the analysis, the Generalized Fluid System Simulation Program (GFSSP) was used. GFSSP is a network flow solver CFD code developed by NASA that has the ability to analyze transient, multi-phase flows, and conjugate heat transfer, along with the inclusion of custom user subroutines developed by the user which can accommodate other simulation requirements. In this paper we present the GFSSP model developed, and the computed results that could be compared with corresponding parameters as measured from experimental testing for the pressure relief valve. Adjustments to GFSSP input parameters allow the anchoring of the GFSSP valve model to test data. This makes it possible to use the GFSSP model as a predictive tool for understanding valve dynamics, as well as evaluating proposed pressure relief valve modifications for performance improvements.
- 19 July 2015
- Published by ASME International
Design of a Tornado Missile Resistant Shield for the Angra Nuclear Plant
The Angra site contains the only two operational nuclear power plants in Brazil and one that is under construction. When Angra Unit 1 was designed the risk of tornadoes was deemed to be vanishingly small and tornadoes were not included in the design basis for the plant. When the question of environmental hazards was revisited for the design basis of Angra Unit 3, tornadoes were included as part of the design basis. Based on this change in philosophy for the Angra site, a review was performed and it was determined that the Raw Water Storage Tank and Reactor Make-up Water Tank, both of which are located outdoors at Angra Unit 1 required protection from tornado driven missiles. The tanks contain water that may be used for emergency cooling, and the water must be available for use during a design basis event. This paper provides an overview of the methodology used to design the tornado missile resistant shield structure for these two tanks.
- 19 July 2015
- Published by ASME International
Design of a Tornado Missile Resistant Shield for the Angra Nuclear Plant
The Angra site contains the only two operational nuclear power plants in Brazil and one that is under construction. When Angra Unit 1 was designed the risk of tornadoes was deemed to be vanishingly small and tornadoes were not included in the design basis for the plant. When the question of environmental hazards was revisited for the design basis of Angra Unit 3, tornadoes were included as part of the design basis. Based on this change in philosophy for the Angra site, a review was performed and it was determined that the Raw Water Storage Tank and Reactor Make-up Water Tank, both of which are located outdoors at Angra Unit 1 required protection from tornado driven missiles. The tanks contain water that may be used for emergency cooling, and the water must be available for use during a design basis event. This paper provides an overview of the methodology used to design the tornado missile resistant shield structure for these two tanks.
- 20 July 2014
- Published by ASME International
Combined Cycle Power Plant Expansion Joint Failure
Engineers design systems based on the best available information about the design conditions. These design conditions are based on a reasonable understanding about how systems will be operated and the pressures and temperatures expected. This paper focuses on the failure of an expansion joint in a hot water system at a combined cycle power plant. The root cause of the failure can be traced to the way the plant was operated. The operation of the plant produced temperatures and pressures that were well beyond the design basis of the expansion joint and the system in which it was used. This failure highlights some considerations in setting the design temperature and pressure for hot water systems, and for the operation of these systems.
- 20 July 2014
- Published by ASME International
Combined Cycle Power Plant Expansion Joint Failure
Engineers design systems based on the best available information about the design conditions. These design conditions are based on a reasonable understanding about how systems will be operated and the pressures and temperatures expected. This paper focuses on the failure of an expansion joint in a hot water system at a combined cycle power plant. The root cause of the failure can be traced to the way the plant was operated. The operation of the plant produced temperatures and pressures that were well beyond the design basis of the expansion joint and the system in which it was used. This failure highlights some considerations in setting the design temperature and pressure for hot water systems, and for the operation of these systems.
- 15 July 2012
- Published by ASME International
- p. 249-253
System for the Automated Mitigation of Hypergolic Propellant Leaks
Hypergolic liquid rocket propellants consist of fuel and oxidizer liquids stored in separate tanks that ignite when mixed. They are favored for propulsion systems where precise pulsing or throttling is required. High reliability is also insured because the liquid chemicals are stable for long periods of time, and no ignition system is required — the fuel and oxidizer simply need to be brought together. These propellants have relatively high vapor pressures, are toxic, and may be carcinogenic. A pool of the liquid will pose a health, fire, or explosion hazard. Therefore, missiles containing these propellants are stored and shipped in canisters that contain a sensor to detect the leakage of these propellants that will sound an alarm at a set concentration. This paper discusses the development of an automated system that is designed to mitigate a leak of the fuel or oxidizer within the canister in order to render the system safe enough to allow access to the missile. The mitigation system neutralizes the leaked propellant. The design and testing of the system with representative propellants is discussed.
- 15 July 2012
- Published by ASME International
- p. 249-253
System for the Automated Mitigation of Hypergolic Propellant Leaks
Hypergolic liquid rocket propellants consist of fuel and oxidizer liquids stored in separate tanks that ignite when mixed. They are favored for propulsion systems where precise pulsing or throttling is required. High reliability is also insured because the liquid chemicals are stable for long periods of time, and no ignition system is required — the fuel and oxidizer simply need to be brought together. These propellants have relatively high vapor pressures, are toxic, and may be carcinogenic. A pool of the liquid will pose a health, fire, or explosion hazard. Therefore, missiles containing these propellants are stored and shipped in canisters that contain a sensor to detect the leakage of these propellants that will sound an alarm at a set concentration. This paper discusses the development of an automated system that is designed to mitigate a leak of the fuel or oxidizer within the canister in order to render the system safe enough to allow access to the missile. The mitigation system neutralizes the leaked propellant. The design and testing of the system with representative propellants is discussed.
- 1 January 2011
- Published by ASME International
- p. 29-34
Analysis of Cured-in-Place Piping for a Nuclear Plant Application
Cured-in-place piping (CIPP) is used to repair existing pressure pipe that has compromised structural integrity and is no longer capable of holding operating pressure without leaking. It is often used to repair buried piping where digging the piping up to replace it would be inconvenient and/or cost prohibitive. CIPP is routinely used to repair water and sewer lines, and an ASTM specification exists to guide the design of the pipe repair for these applications. CIPP can also be used as a repair technique for piping at nuclear power plants; however, such use must be approved on a case-by-case basis. This paper discusses some of the design challenges associated with designing the CIPP for a nuclear plant application. It presents an overview of the analytical approach and the results.
- 1 January 2011
- Published by ASME International
- p. 29-34
Analysis of Cured-in-Place Piping for a Nuclear Plant Application
Cured-in-place piping (CIPP) is used to repair existing pressure pipe that has compromised structural integrity and is no longer capable of holding operating pressure without leaking. It is often used to repair buried piping where digging the piping up to replace it would be inconvenient and/or cost prohibitive. CIPP is routinely used to repair water and sewer lines, and an ASTM specification exists to guide the design of the pipe repair for these applications. CIPP can also be used as a repair technique for piping at nuclear power plants; however, such use must be approved on a case-by-case basis. This paper discusses some of the design challenges associated with designing the CIPP for a nuclear plant application. It presents an overview of the analytical approach and the results.