Sri Saravana Konganapuram Narasimma Bharathi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Sri Saravana Konganapuram Narasimma Bharathi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
John Arnason
2 shared publicationsKathleen Dunn
2 shared publicationsMatthew Armstrong
2 shared publicationsAnton Bonacci
Department of Nanoscale Engineering, College of Nanotechnology, Science, and Engineering, University at Albany – State University of New York, Albany, New York, 12203
1 shared publicationBhavani Sasank Nagothi
1 shared publicationEric W. Wales
1 shared publication
Latest Publications
- Open Access
- 23 July 2026
- Published by Elsevier in SSRN Electronic Journal
Effect of Ni Concentration on Surface Properties of Nickel Ferrite and Implications for CRUD Deposition in PWRs
Corrosion products such as magnetite and nickel ferrite in the coolant of pressurized water reactors lead to particulate fouling, negatively impacting power distribution and changing local chemistry (local pH and B concentration). Corrosion product deposits (CRUD) on fuel cladding can reduce heat transfer due to the lower thermal conductivity of the particles, and the porous nature of the deposit may cause local boiling of coolant, impacting the reactor efficiency. As deposition of CRUD depends in part on the surface charge of the particles and of the nearby surfaces, this study investigated the effect of Ni content on the surface properties of Ni-Fe ferrite, a major constituent of CRUD. Ferrite particles with compositions ranging from magnetite (Fe3O4) to stoichiometric nickel ferrite (NiFe2O4) were synthesized by hydrothermal and ethylene glycol-based solvothermal methods. Both the synthesis routes yielded particles averaging 100 nm in size, though the hydrothermal method produced octahedral particles, whereas the solvothermal method yielded spherical clusters. For both morphologies, the isoelectric point of the ferrites increased with higher nickel content, though this effect was more pronounced for the octahedral particles. Ultimately, mapping these surface properties provides a qualitative understanding of CRUD deposition in nuclear reactors.
- 23 July 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEffect of Ni Concentration on Surface Properties of Nickel Ferrite and Implications for CRUD Deposition in PWRs
Corrosion products such as magnetite and nickel ferrite in the coolant of pressurized water reactors lead to particulate fouling, negatively impacting power distribution and changing local chemistry (local pH and B concentration). Corrosion product deposits (CRUD) on fuel cladding can reduce heat transfer due to the lower thermal conductivity of the particles, and the porous nature of the deposit may cause local boiling of coolant, impacting the reactor efficiency. As deposition of CRUD depends in part on the surface charge of the particles and of the nearby surfaces, this study investigated the effect of Ni content on the surface properties of Ni-Fe ferrite, a major constituent of CRUD. Ferrite particles with compositions ranging from magnetite (Fe3O4) to stoichiometric nickel ferrite (NiFe2O4) were synthesized by hydrothermal and ethylene glycol-based solvothermal methods. Both the synthesis routes yielded particles averaging 100 nm in size, though the hydrothermal method produced octahedral particles, whereas the solvothermal method yielded spherical clusters. For both morphologies, the isoelectric point of the ferrites increased with higher nickel content, though this effect was more pronounced for the octahedral particles. Ultimately, mapping these surface properties provides a qualitative understanding of CRUD deposition in nuclear reactors.
- 2 March 2026
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 82 (5) , 400-410
Experimental and Modeling Investigation of Factors Affecting Crud Deposition in PWRs: Role of Zn, Ni, and Redox Potential
Corrosion products such as nickel-iron spinel oxides (known as crud) in the coolant circuits of pressurized water (PWR) reactors may lead to particulate fouling, negatively impacting power distribution and changing local chemistry. The transport and deposition of particles depend in part on the surface charge of the particles and the nearby surfaces. Tuning coolant chemistry and the composition of the primary circuit materials has been used as an empirical lever for crud mitigation, but experimentation is limited by a variety of other constraints in a working reactor. To simulate the transport and deposition process of crud particles, a multiscale multiphysics model was designed for a simple geometry representing hot leg piping with fluid properties reflecting a PWR environment. A macroscale model solves the fluid flow and particle trajectories and is later coupled with a fine-scale particle adhesion model. To ensure the relevance of the fine-scale model, surface properties of synthetic crud particles covering a range of compositions and water chemistry (Zn addition and reducing environment) were measured and incorporated into the simulations. Preliminary results of the fine-scale simulations examining the effect of the surface potential of the crud particles and the pipe surface are consistent with expectations from Derjaguin, Landau, Verwey, and Overbeek theory and support observations from test loop experiments.
- 2 March 2026
- Published by Association for Materials Protection and Performance (AMPP) in Corrosion
- Vol. 82 (5) , 400-410
Experimental and Modeling Investigation of Factors Affecting Crud Deposition in PWRs: Role of Zn, Ni, and Redox Potential
Corrosion products such as nickel-iron spinel oxides (known as crud) in the coolant circuits of pressurized water (PWR) reactors may lead to particulate fouling, negatively impacting power distribution and changing local chemistry. The transport and deposition of particles depend in part on the surface charge of the particles and the nearby surfaces. Tuning coolant chemistry and the composition of the primary circuit materials has been used as an empirical lever for crud mitigation, but experimentation is limited by a variety of other constraints in a working reactor. To simulate the transport and deposition process of crud particles, a multiscale multiphysics model was designed for a simple geometry representing hot leg piping with fluid properties reflecting a PWR environment. A macroscale model solves the fluid flow and particle trajectories and is later coupled with a fine-scale particle adhesion model. To ensure the relevance of the fine-scale model, surface properties of synthetic crud particles covering a range of compositions and water chemistry (Zn addition and reducing environment) were measured and incorporated into the simulations. Preliminary results of the fine-scale simulations examining the effect of the surface potential of the crud particles and the pipe surface are consistent with expectations from Derjaguin, Landau, Verwey, and Overbeek theory and support observations from test loop experiments.
- 1 April 2020
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 245
A non-enzymatic urea sensor based on the nickel sulfide / graphene oxide modified glassy carbon electrode
- 1 April 2020
- Published by Elsevier in Materials Chemistry and Physics
- Vol. 245
A non-enzymatic urea sensor based on the nickel sulfide / graphene oxide modified glassy carbon electrode