Ronald Izidoro Reis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ronald Izidoro Reis has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
C. M. D. Starling
1 shared publicationDaniel Fraga Sias
Departamento de Ciência e Tecnologia Aeroespacial, Instituto de Aeronáutica e Espaço, São José dos Campos, Brazil
1 shared publicationGilberto Petraconi Filho
Instituto Tecnológico de Aeronáutica, São José dos Campos, Brazil
1 shared publicationLuiz Claudio Pardini
Instituto Tecnológico de Aeronáutica, São José dos Campos, Brazil
1 shared publicationLuiz Cláudio Pardini
Departamento de Ciência e Tecnologia Aeroespacial (DCTA)
1 shared publicationP. J. Modenesi
1 shared publication
Latest Publications
- 1 October 2019
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 40 (10) , 1-16
Low-Energy Ablation and Low Thermal Diffusivity of a CFRC Composite Modified by SiC
- 1 October 2019
- Published by Springer Nature in International Journal of Thermophysics
- Vol. 40 (10) , 1-16
Low-Energy Ablation and Low Thermal Diffusivity of a CFRC Composite Modified by SiC
- Open Access
- 30 October 2016
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 8 (4) , 483-490
Anomalous Behavior of a Solid Rocket Motor Nozzle Insert During Static Firing Test
This paper presents the study and development of a firing test used to evaluate the behavior of a solid rocket motor. The motivation for the development of a subscale solid rocket motor with end burning propellant grain geometry arose from the need to evaluate the nozzle inserts of graphite for the possible replacement with the carbon fiber-reinforced carbon composite. These subscale solid rocket motors, simulating full scale motor operating time, but with mass flow far below, aim to determine the ablative characteristics of composite materials as a function of operating time. The objective was to correlate the mass flow between subscale solid rocket motors and full scale using insert data materials such as graphite and carbon fiber-reinforced carbon composites, which have ablative characteristics determined in subscale solid rocket motors used at the Instituto de Aeronáutica e Espaço. The critical section to evaluate the test device is rocket nozzle throat region. Analysis of the materials of the subsonic and supersonic nozzle insert parts was performed after the burning tests. It was found the formation of a thin layer of material deposited after the test. The deposited coating layer was analyzed by electron dispersive x-ray analysis and scanning electron microscopy. The results analyzed by these methods showed that there were aluminum and carbon in the coating. Finally, the material was analyzed by x-ray diffraction, and the results showed the presence of aluminum oxide. It was also noticed that, because of the unexpected coating deposition forming material in exit conical and throat of the insert that the effect of ablation was not observed.
- 30 October 2016
- Published by FapUNIFESP (SciELO) in Journal of Aerospace Technology and Management
- Vol. 8 (4) , 483-490
Open AccessAnomalous Behavior of a Solid Rocket Motor Nozzle Insert During Static Firing Test
This paper presents the study and development of a firing test used to evaluate the behavior of a solid rocket motor. The motivation for the development of a subscale solid rocket motor with end burning propellant grain geometry arose from the need to evaluate the nozzle inserts of graphite for the possible replacement with the carbon fiber-reinforced carbon composite. These subscale solid rocket motors, simulating full scale motor operating time, but with mass flow far below, aim to determine the ablative characteristics of composite materials as a function of operating time. The objective was to correlate the mass flow between subscale solid rocket motors and full scale using insert data materials such as graphite and carbon fiber-reinforced carbon composites, which have ablative characteristics determined in subscale solid rocket motors used at the Instituto de Aeronáutica e Espaço. The critical section to evaluate the test device is rocket nozzle throat region. Analysis of the materials of the subsonic and supersonic nozzle insert parts was performed after the burning tests. It was found the formation of a thin layer of material deposited after the test. The deposited coating layer was analyzed by electron dispersive x-ray analysis and scanning electron microscopy. The results analyzed by these methods showed that there were aluminum and carbon in the coating. Finally, the material was analyzed by x-ray diffraction, and the results showed the presence of aluminum oxide. It was also noticed that, because of the unexpected coating deposition forming material in exit conical and throat of the insert that the effect of ablation was not observed.
- 1 July 2007
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 189 (1-3) , 199-205
A model for melting rate phenomena in GMA welding
- 1 July 2007
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 189 (1-3) , 199-205
A model for melting rate phenomena in GMA welding
- 1 September 2005
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 10 (5) , 610-616
Wire melting phenomena in gas metal arc welding
The wire melting rate in gas metal arc welding using constant voltage power supplies is well described by a parabolic model that considers the effects of electrical resistance and arc heating. However, tests performed with constant current power supplies indicate that the melting rate can deviate from this model when welding current is close to the globular–spray transition value. Although the causes of this anomaly have not yet been well established, most authors consider them to be related to variations in liquid metal temperature close to the metal transfer mode transition current. The present work evaluates the effect of welding parameters on the wire melting rate when a constant current power supply is used. A numerical model that considers the contribution of both Joule and arc heating was developed to calculate the temperature distribution in the wire and its melting rate. The model was used to assess the changes in either arc heating or metal vaporisation that might explain the melting irregularities. High speed cinematography was used to analyse metal transfer in the current range associated with the melting irregularities.
- 1 September 2005
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 10 (5) , 610-616
Wire melting phenomena in gas metal arc welding
The wire melting rate in gas metal arc welding using constant voltage power supplies is well described by a parabolic model that considers the effects of electrical resistance and arc heating. However, tests performed with constant current power supplies indicate that the melting rate can deviate from this model when welding current is close to the globular–spray transition value. Although the causes of this anomaly have not yet been well established, most authors consider them to be related to variations in liquid metal temperature close to the metal transfer mode transition current. The present work evaluates the effect of welding parameters on the wire melting rate when a constant current power supply is used. A numerical model that considers the contribution of both Joule and arc heating was developed to calculate the temperature distribution in the wire and its melting rate. The model was used to assess the changes in either arc heating or metal vaporisation that might explain the melting irregularities. High speed cinematography was used to analyse metal transfer in the current range associated with the melting irregularities.