Shamzin Yazdanian
Research Subjects
Shamzin Yazdanian has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Zhan Wen Chen
Department of Mechanical Engineering, Auckland University of Technology, Auckland, New Zealand
3 shared publications G. Littlefair
Deakin University
2 shared publicationsGuy Littlefair
AUT University
2 shared publicationsZ.W. Chen
2 shared publicationsZhan W. Chen
AUT University
2 shared publications- Steve Ales
Department of Mechanical Engineering, PNG University of Technology, Lae, Papua New Guinea
1 shared publication
Latest Publications
- Open Access
- 6 October 2026
- Published by IntechOpen
Advances in Welding Technologies for Titanium Alloys: Processes, Metallurgy, Dissimilar Joining and Industrial Applications
This chapter presents a structured review of recent development in titanium alloy welding technologies, focusing on welding metallurgy, fusion and solid-state joining processes, dissimilar-metal welding, industrial applications, In-situ monitoring, and emerging intelligent welding systems. It examines the metallurgical sensitivity of titanium alloys to phase transformations, contamination, residual stress, cooling rate, microstructural evolution, and intermetallic compound formation. Major welding processes are reviewed, including gas tungsten arc welding, plasma arc welding, electron beam welding, laser beam welding, resistance spot welding, friction welding, friction stir welding, and diffusion bonding. Recent developments have extended the capability of conventional processes. Electron-beam welding, for instance, has produced defect-free joints in titanium plates up to 100 mm thick with reported joint efficiencies of 100%, while reduced-pressure laser welding has achieved penetration depths of approximately 20 mm with aspect ratios up to 17:1. Narrow-gap laser–TIG hybrid welding has similarly been applied to plates approximately 25–50 mm thick. In solid-state joining, friction stir welded Ti-6Al-4 V butt joints commonly achieve around 95% joint efficiency, although tool wear and high process forces continue to restrict wider industrial adoption. For dissimilar titanium–steel joints, composite interlayers have proven more effective than single interlayers at limiting formation of brittle intermetallic layers, with a Ta–Cu interlayer producing tensile strength of about 450 MPa. The chapter also highlights recent process developments aimed at improving weld quality, joint performance, and manufacturing reliability. Current limitations and future research directions are also identified to support the development of high-integrity titanium alloy welds for advanced engineering applications.
- 6 October 2026
- Published by IntechOpen
Open AccessAdvances in Welding Technologies for Titanium Alloys: Processes, Metallurgy, Dissimilar Joining and Industrial Applications
This chapter presents a structured review of recent development in titanium alloy welding technologies, focusing on welding metallurgy, fusion and solid-state joining processes, dissimilar-metal welding, industrial applications, In-situ monitoring, and emerging intelligent welding systems. It examines the metallurgical sensitivity of titanium alloys to phase transformations, contamination, residual stress, cooling rate, microstructural evolution, and intermetallic compound formation. Major welding processes are reviewed, including gas tungsten arc welding, plasma arc welding, electron beam welding, laser beam welding, resistance spot welding, friction welding, friction stir welding, and diffusion bonding. Recent developments have extended the capability of conventional processes. Electron-beam welding, for instance, has produced defect-free joints in titanium plates up to 100 mm thick with reported joint efficiencies of 100%, while reduced-pressure laser welding has achieved penetration depths of approximately 20 mm with aspect ratios up to 17:1. Narrow-gap laser–TIG hybrid welding has similarly been applied to plates approximately 25–50 mm thick. In solid-state joining, friction stir welded Ti-6Al-4 V butt joints commonly achieve around 95% joint efficiency, although tool wear and high process forces continue to restrict wider industrial adoption. For dissimilar titanium–steel joints, composite interlayers have proven more effective than single interlayers at limiting formation of brittle intermetallic layers, with a Ta–Cu interlayer producing tensile strength of about 450 MPa. The chapter also highlights recent process developments aimed at improving weld quality, joint performance, and manufacturing reliability. Current limitations and future research directions are also identified to support the development of high-integrity titanium alloy welds for advanced engineering applications.
- 1 June 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (8) , 2217-2233
Effects of pin size and of using an interlayer on interface bonding and fatigue strength of AA2024 to Ti6Al4V lap joints made using friction stir welding
- 1 June 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (8) , 2217-2233
Effects of pin size and of using an interlayer on interface bonding and fatigue strength of AA2024 to Ti6Al4V lap joints made using friction stir welding
- 1 May 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 634, 37-45
Microstructures in interface region and mechanical behaviours of friction stir lap Al6060 to Ti–6Al–4V welds
- 1 May 2015
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 634, 37-45
Microstructures in interface region and mechanical behaviours of friction stir lap Al6060 to Ti–6Al–4V welds
- 1 January 2014
- Published by The Society of Materials Engineering for Resources of Japan in International Journal of the Society of Materials Engineering for Resources
- Vol. 20 (2) , 186-190
Friction Stir Lap Welding of Light Alloys
- 1 January 2014
- Published by The Society of Materials Engineering for Resources of Japan in International Journal of the Society of Materials Engineering for Resources
- Vol. 20 (2) , 186-190
Friction Stir Lap Welding of Light Alloys
- 6 December 2012
- Published by Springer Nature in Journal of Materials Science
- Vol. 48 (6) , 2624-2634
Effects of tool positioning on joint interface microstructure and fracture strength of friction stir lap Al-to-steel welds
- 6 December 2012
- Published by Springer Nature in Journal of Materials Science
- Vol. 48 (6) , 2624-2634
Effects of tool positioning on joint interface microstructure and fracture strength of friction stir lap Al-to-steel welds
- 7 July 2011
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (3) , 1251-1261
Effects of friction stir lap welding parameters on weld features on advancing side and fracture strength of AA6060-T5 welds
- 7 July 2011
- Published by Springer Nature in Journal of Materials Science
- Vol. 47 (3) , 1251-1261
Effects of friction stir lap welding parameters on weld features on advancing side and fracture strength of AA6060-T5 welds
- 1 July 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 275, 77-80
Effect of Tool Speeds during Friction Stir Lap Welding on Mode of Fracture and Fracture Strength of Al 6060-T5 Joints
Friction stir lap welding (FSLW) of an age hardened Al alloy and evaluations of how FS speeds affected hooking and how hooking and softening due to FS affected fracture strength of the lap welds have been conducted. It was found that increasing rotation speed () and reducing welding speed (v) increased the stir zone size (AB-SZ) and also hook size (h), although a maximum value of h (hMax) reached. The features of hooks for the observed (,v)- AB-SZ-h relationships are presented and explained. It was found that when h increased to a value of ~ 0.9 mm (for the 3 mm alloy sheets), it started to invoke a significant effect on reducing fracture strength. Factors such as FS softening and insufficient joining, limited the fracture strength of the lap welds for small h values and these are presented and discussed.
- 1 July 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 275, 77-80
Effect of Tool Speeds during Friction Stir Lap Welding on Mode of Fracture and Fracture Strength of Al 6060-T5 Joints
Friction stir lap welding (FSLW) of an age hardened Al alloy and evaluations of how FS speeds affected hooking and how hooking and softening due to FS affected fracture strength of the lap welds have been conducted. It was found that increasing rotation speed () and reducing welding speed (v) increased the stir zone size (AB-SZ) and also hook size (h), although a maximum value of h (hMax) reached. The features of hooks for the observed (,v)- AB-SZ-h relationships are presented and explained. It was found that when h increased to a value of ~ 0.9 mm (for the 3 mm alloy sheets), it started to invoke a significant effect on reducing fracture strength. Factors such as FS softening and insufficient joining, limited the fracture strength of the lap welds for small h values and these are presented and discussed.
- 1 July 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 275, 73-76
Fracture Strengths of Mg Alloy AZ31B-H24 Friction Stir Lap Welds
The effects of selected friction stir lap welding parameters on fracture strength of Mg alloy AZ31B-H24 welds have been studied. Rotation speed has been found to affect significantly the flow related hook size formation. Furthermore, fracture strength decreased almost linearly with hook size. A small amount of softening was detected in fracture location that was outside the nugget zone and thus this softening may only adversely affect the fracture strength slightly. Finally, simulation results are presented to show the uneven stress distribution in a lap geometry which together with the relative brittleness of the stir material must be the cause to have significantly reduced the fracture strength.
- 1 July 2011
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 275, 73-76
Fracture Strengths of Mg Alloy AZ31B-H24 Friction Stir Lap Welds
The effects of selected friction stir lap welding parameters on fracture strength of Mg alloy AZ31B-H24 welds have been studied. Rotation speed has been found to affect significantly the flow related hook size formation. Furthermore, fracture strength decreased almost linearly with hook size. A small amount of softening was detected in fracture location that was outside the nugget zone and thus this softening may only adversely affect the fracture strength slightly. Finally, simulation results are presented to show the uneven stress distribution in a lap geometry which together with the relative brittleness of the stir material must be the cause to have significantly reduced the fracture strength.