Mohammed Laissaoui
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammed Laissaoui has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Housseyn Karoua
Centre de Développement des Energies Renouvelables CDER
4 shared publications - Amar Bouhallassa
Centre de Développement des Energies Renouvelables CDER
3 shared publications - Sabrina Lecheheb
Centre de Développement des Energies Renouvelables CDER
3 shared publications - Abdelkader Touil
Scientific and Technical Research Center on Arid Regions, CRSTRA, Biskra, Algeria
2 shared publications - Benaoumeur Aour
Département de Génie Mécanique, Laboratoire de Biomécanique Appliquée et Biomatériaux (LABAB), Ecole Nationale Polytechnique d’Oran—Maurice Audin, BP 1523 El Mnaour, Oran 31000, Algeria
2 shared publications - Cornel Panait
University MARITIMA of Constanta, 900663 Constanta, Romania
2 shared publications
Latest Publications
- Open Access
- 30 March 2026
- Published by Al-Qadisiyah Journal for Engineering Sciences (QJES) in Al-Qadisiyah Journal for Engineering Sciences
- Vol. 19 (1) , 98-109
Thermodynamic analysis of small-scale CSP based on ORC systems compared with PV systems in North Africa zone. (Algeria as a case study)
This study presents a simulation of electricity generation systems utilizing solar energy, employing TRNSYS and EES software to address the energy needs of isolated areas in Algeria. Two solar energy systems were compared: the CSP-ORC and the Photovoltaic, analyzed across three regions: Adrar, Illizi, and El-Bayadh. The CSP-ORC system was enhanced by incorporating components for optimizing the operation of the pump within the ORC, as well as integrating a solar photovoltaic system with battery storage at a capacity of 50 kW. The estimated electrical power generated by the studied systems is approximately 1 MW. We compared the technical performance of a 1 MW s-ORC system with thermal energy storage against that of a solar photovoltaic system of the same capacity. This analysis underscores the viability of both CSP-ORC and PV systems for electricity generation in isolated arid regions of Algeria. However, the superior performance of the PV system, particularly during the winter months, suggests that while CSP-ORC systems are promising, they may require further enhancements or integrated solutions (such as hybrid systems) to improve output and reliability across all seasons. The economic analysis highlights the cost-effectiveness of PV systems, which have lower investment, maintenance costs, and LCOE than CSP-ORC. The lowest LCOE (0.0311 €/kWh) and fastest payback (3.62 years) were observed in Illizi for PV, while CSP-ORC had the highest LCOE in El-Bayadh. Environmentally, PV reduces 55.2 tons of CO2 emissions in Illizi, whereas CSP-ORC, generating more electricity, prevents 84 tons. Both systems significantly cut emissions compared to diesel generators.
- 30 March 2026
- Published by Al-Qadisiyah Journal for Engineering Sciences (QJES) in Al-Qadisiyah Journal for Engineering Sciences
- Vol. 19 (1) , 98-109
Open AccessThermodynamic analysis of small-scale CSP based on ORC systems compared with PV systems in North Africa zone. (Algeria as a case study)
This study presents a simulation of electricity generation systems utilizing solar energy, employing TRNSYS and EES software to address the energy needs of isolated areas in Algeria. Two solar energy systems were compared: the CSP-ORC and the Photovoltaic, analyzed across three regions: Adrar, Illizi, and El-Bayadh. The CSP-ORC system was enhanced by incorporating components for optimizing the operation of the pump within the ORC, as well as integrating a solar photovoltaic system with battery storage at a capacity of 50 kW. The estimated electrical power generated by the studied systems is approximately 1 MW. We compared the technical performance of a 1 MW s-ORC system with thermal energy storage against that of a solar photovoltaic system of the same capacity. This analysis underscores the viability of both CSP-ORC and PV systems for electricity generation in isolated arid regions of Algeria. However, the superior performance of the PV system, particularly during the winter months, suggests that while CSP-ORC systems are promising, they may require further enhancements or integrated solutions (such as hybrid systems) to improve output and reliability across all seasons. The economic analysis highlights the cost-effectiveness of PV systems, which have lower investment, maintenance costs, and LCOE than CSP-ORC. The lowest LCOE (0.0311 €/kWh) and fastest payback (3.62 years) were observed in Illizi for PV, while CSP-ORC had the highest LCOE in El-Bayadh. Environmentally, PV reduces 55.2 tons of CO2 emissions in Illizi, whereas CSP-ORC, generating more electricity, prevents 84 tons. Both systems significantly cut emissions compared to diesel generators.
- Open Access
- 31 December 2025
- Published by Al-Qadisiyah Journal for Engineering Sciences (QJES) in Al-Qadisiyah Journal for Engineering Sciences
- Vol. 18 (4) , 483-491
Energetic, economic and environmental (3E) study of combined concentrating solar power plant and desalination small scale capacity for arid areas
Water scarcity is a growing global problem affecting millions of people and ecosystems. It is the result of a number of factors, including population growth and climate change. Sustainable water management practices, efficient use of resources, and innovative technologies are essential to address this challenge. By implementing these strategies, we can work towards ensuring a reliable water supply for future generations and mitigating the impact of water scarcity on communities and the environment. This study proposes and investigates a promising solar brackish water desalination system based on reverse osmosis technology powered by a solar organic Rankine cycle. This paper aims to perform a technical and economic study of Organic Rankine Cycle (ORC) powered by concentrating solar Fresnel field combined with desalination units in an isolated region of Algeria (region of Hassi Khebi), taking into account the power fluctuation of the solar plant, ensuring an acceptable quality of produced water. In particular, the prediction of the performances of the different components (the power plant and the desalination unit) is achieved through the modeling of the reverse osmosis unit and the simulation of concentrating solar power (CSP). The nominal capacity of the concentrating solar power plant is 1.2 MW based on linear solar Fresnel concentrators, the results have shown that the capacity of the desalination unit under nominal conditions reaches 15000 m3/day; this value represents a capacity factor of 24% according to the solar power availability, while the capacity factor of the solar power plant is around 20% with a solar electric efficiency of 15\%. The economic analysis shows that the levelized cost of the water produced is estimated at 0.92 ($/m3), as is the cost of the electricity generated, which is 0.25 $/kWh. Finally, there is the cost amortization period, which is 9.66 years. The established carbon balance shows the importance of this type of system compared to conventional systems.
- 31 December 2025
- Published by Al-Qadisiyah Journal for Engineering Sciences (QJES) in Al-Qadisiyah Journal for Engineering Sciences
- Vol. 18 (4) , 483-491
Open AccessEnergetic, economic and environmental (3E) study of combined concentrating solar power plant and desalination small scale capacity for arid areas
Water scarcity is a growing global problem affecting millions of people and ecosystems. It is the result of a number of factors, including population growth and climate change. Sustainable water management practices, efficient use of resources, and innovative technologies are essential to address this challenge. By implementing these strategies, we can work towards ensuring a reliable water supply for future generations and mitigating the impact of water scarcity on communities and the environment. This study proposes and investigates a promising solar brackish water desalination system based on reverse osmosis technology powered by a solar organic Rankine cycle. This paper aims to perform a technical and economic study of Organic Rankine Cycle (ORC) powered by concentrating solar Fresnel field combined with desalination units in an isolated region of Algeria (region of Hassi Khebi), taking into account the power fluctuation of the solar plant, ensuring an acceptable quality of produced water. In particular, the prediction of the performances of the different components (the power plant and the desalination unit) is achieved through the modeling of the reverse osmosis unit and the simulation of concentrating solar power (CSP). The nominal capacity of the concentrating solar power plant is 1.2 MW based on linear solar Fresnel concentrators, the results have shown that the capacity of the desalination unit under nominal conditions reaches 15000 m3/day; this value represents a capacity factor of 24% according to the solar power availability, while the capacity factor of the solar power plant is around 20% with a solar electric efficiency of 15\%. The economic analysis shows that the levelized cost of the water produced is estimated at 0.92 ($/m3), as is the cost of the electricity generated, which is 0.25 $/kWh. Finally, there is the cost amortization period, which is 9.66 years. The established carbon balance shows the importance of this type of system compared to conventional systems.
- Open Access
- 17 July 2025
- Published by MDPI AG in Technologies
- Vol. 13 (7) , 308
Modeling and Efficiency Analysis of an Immersed Heat Exchanger for Solar-Powered Industrial Heat Processes: A Case Study on Wool Washing
Efficient water heating is essential for wool-washing processes, which demand temperatures above 70 °C. To meet this requirement sustainably, a parabolic trough solar concentrator system is proposed in this paper as an alternative to conventional natural gas systems. The design centers on a water pool constructed from bricks reinforced with an internal steel layer, enhancing heat exchange efficiency. Also, various synthetic oils were analyzed as heat transfer fluids (HTFs) within an immersed heat exchanger, such as Thermia B oil, Heat Transfer Oil 32, biphasic oil, and Therminol vp1 oil. Numerical simulations were performed using ANSYS CFX v19.2 software with the k-ε turbulence model to evaluate the thermal performance and temperature distribution. The results demonstrate the superior efficiency of the solar-powered system, with the steel-reinforced pool achieving optimal water temperatures between 78 °C and 85 °C, exceeding the required threshold for industrial wool washing. Among the various synthetic oils analyzed, Thermia B emerged as the most effective heat transfer fluid, maintaining water temperatures in the range of 75 °C to 85 °C. This superior thermal performance is attributed to its high thermal conductivity and reduced heat loss, ensuring consistent and optimal heat distribution for the wool-washing process.
- 17 July 2025
- Published by MDPI AG in Technologies
- Vol. 13 (7) , 308
Open AccessModeling and Efficiency Analysis of an Immersed Heat Exchanger for Solar-Powered Industrial Heat Processes: A Case Study on Wool Washing
Efficient water heating is essential for wool-washing processes, which demand temperatures above 70 °C. To meet this requirement sustainably, a parabolic trough solar concentrator system is proposed in this paper as an alternative to conventional natural gas systems. The design centers on a water pool constructed from bricks reinforced with an internal steel layer, enhancing heat exchange efficiency. Also, various synthetic oils were analyzed as heat transfer fluids (HTFs) within an immersed heat exchanger, such as Thermia B oil, Heat Transfer Oil 32, biphasic oil, and Therminol vp1 oil. Numerical simulations were performed using ANSYS CFX v19.2 software with the k-ε turbulence model to evaluate the thermal performance and temperature distribution. The results demonstrate the superior efficiency of the solar-powered system, with the steel-reinforced pool achieving optimal water temperatures between 78 °C and 85 °C, exceeding the required threshold for industrial wool washing. Among the various synthetic oils analyzed, Thermia B emerged as the most effective heat transfer fluid, maintaining water temperatures in the range of 75 °C to 85 °C. This superior thermal performance is attributed to its high thermal conductivity and reduced heat loss, ensuring consistent and optimal heat distribution for the wool-washing process.
- Open Access
- 14 April 2025
- Published by MDPI AG in Preprints.org
Modeling and Efficiency Analysis of an Immersed Heat Exchanger for Solar-Powered Industrial Heat Processes: A Case Study on Wool Washing
Efficient water heating is essential for wool washing processes, which demand temperatures above 70°C. To meet this requirement sustainably, a parabolic trough solar concentrator system was proposed as an alternative to conventional natural gas systems. The design centers on a water pool constructed from bricks reinforced with an internal steel layer, enhancing heat exchange efficiency. Also, Various synthetic oils were analyzed as heat transfer fluids (HTFs) within an immersed heat exchanger, such as Thermia B oil, Heat transfer oil 32, Biphasic oil, and Therminol vp1 oil Nu-merical simulations have been done using ANSYS CFX software with the k-ε turbulence model, to evaluate the thermal performance and temperature distribution. Results demonstrate the superior efficiency of the solar-powered system, with the steel-reinforced pool achieving optimal water temperatures between 78°C and 85°C, exceeding the required threshold for industrial wool washing. Among various synthetic oils analyzed, Thermia B emerged as the most effective heat transfer fluid, maintaining water temperatures in the range of 75°C to 85°C. This superior thermal performance is attributed to its high thermal conductivity and reduced heat loss, ensuring con-sistent and optimal heat distribution for the wool washing process.
- 14 April 2025
- Published by MDPI AG in Preprints.org
Open AccessModeling and Efficiency Analysis of an Immersed Heat Exchanger for Solar-Powered Industrial Heat Processes: A Case Study on Wool Washing
Efficient water heating is essential for wool washing processes, which demand temperatures above 70°C. To meet this requirement sustainably, a parabolic trough solar concentrator system was proposed as an alternative to conventional natural gas systems. The design centers on a water pool constructed from bricks reinforced with an internal steel layer, enhancing heat exchange efficiency. Also, Various synthetic oils were analyzed as heat transfer fluids (HTFs) within an immersed heat exchanger, such as Thermia B oil, Heat transfer oil 32, Biphasic oil, and Therminol vp1 oil Nu-merical simulations have been done using ANSYS CFX software with the k-ε turbulence model, to evaluate the thermal performance and temperature distribution. Results demonstrate the superior efficiency of the solar-powered system, with the steel-reinforced pool achieving optimal water temperatures between 78°C and 85°C, exceeding the required threshold for industrial wool washing. Among various synthetic oils analyzed, Thermia B emerged as the most effective heat transfer fluid, maintaining water temperatures in the range of 75°C to 85°C. This superior thermal performance is attributed to its high thermal conductivity and reduced heat loss, ensuring con-sistent and optimal heat distribution for the wool washing process.
- 10 January 2025
- Published by Springer Nature
- p. 153-157
Linear Fresnel Collectors for Industrial Process Heat
- 10 January 2025
- Published by Springer Nature
- p. 153-157
Linear Fresnel Collectors for Industrial Process Heat
- 10 January 2025
- Published by Springer Nature
- p. 125-128
Modelling and Simulation of Heat Exchange in Single-Phase Flow of Nanofluids Through the Parabolic-Trough Collector's Solar Receivers
- 10 January 2025
- Published by Springer Nature
- p. 125-128
Modelling and Simulation of Heat Exchange in Single-Phase Flow of Nanofluids Through the Parabolic-Trough Collector's Solar Receivers
- 10 January 2025
- Published by Springer Nature
- p. 149-152
Integration of Parabolic Trough Technology for Industrial Heat Processes in Algeria: Simulation and Optimization Using TRNSYS and EES
- 10 January 2025
- Published by Springer Nature
- p. 149-152
Integration of Parabolic Trough Technology for Industrial Heat Processes in Algeria: Simulation and Optimization Using TRNSYS and EES
- 1 March 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 133, 659-670
Techno-economic analysis of a stand-alone solar desalination plant at variable load conditions
- 1 March 2018
- Published by Elsevier in Applied Thermal Engineering
- Vol. 133, 659-670
Techno-economic analysis of a stand-alone solar desalination plant at variable load conditions
- 28 December 2017
- Published by International Information and Engineering Technology Association in Journal Européen des Systèmes Automatisés
- Vol. 50 (4-6)
A TRNSYS model of a direct contact membrane distillation (DCMD) system coupled to a flat plate solar collector (FPC)
Modélisation parTRNSYS d'un système de distillation membranaire à contact direct (DCMD) couplé à un capteur solaire plan (FPC) A TRNSYS model of a direct contact membrane distillation (DCMD) system coupled to a flat plate solar collector (FPC)
- 28 December 2017
- Published by International Information and Engineering Technology Association in Journal Européen des Systèmes Automatisés
- Vol. 50 (4-6)
A TRNSYS model of a direct contact membrane distillation (DCMD) system coupled to a flat plate solar collector (FPC)
Modélisation parTRNSYS d'un système de distillation membranaire à contact direct (DCMD) couplé à un capteur solaire plan (FPC) A TRNSYS model of a direct contact membrane distillation (DCMD) system coupled to a flat plate solar collector (FPC)