Yu. G. Sirenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yu. G. Sirenko has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Andrey Aleksandrovich Sidorenko
Saint Petersburg Mining University
3 shared publications A A Ilinets
Saint-Petersburg Mining University, 2, 21 linia, Vasilievski ostrov, Saint-Petersburg, 199106, Russia
1 shared publicationA. B. Chayanov
1 shared publication- Evgenii R. Kovalskii
Saint-Petersburg Mining University
1 shared publication N. A. Litvinovskaya
1 shared publicationS. S. Andreiko
1 shared publication
Latest Publications
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1333 (3) , 032078
An assessment of multiple seam stress conditions using a 3-D numerical modelling approach
The paper presents results of 3-D numerical modeling by a finite element method of the stress condition of the rock massif when undermining the flat thick coal seam. As a result of the executed research, the authors establish influences of the pillars left between longwall panels in previously mined top seam 70 on distribution of stress in the current mining seam 69. The need for application of 3-D numerical models to take a note of imposing the bearing pressure of a longwall and the increased stress from the pillar is shown. Recommendations on the location of entries of the longwall panel when undermining the coal seam are made.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1333 (3) , 032078
Open AccessAn assessment of multiple seam stress conditions using a 3-D numerical modelling approach
The paper presents results of 3-D numerical modeling by a finite element method of the stress condition of the rock massif when undermining the flat thick coal seam. As a result of the executed research, the authors establish influences of the pillars left between longwall panels in previously mined top seam 70 on distribution of stress in the current mining seam 69. The need for application of 3-D numerical models to take a note of imposing the bearing pressure of a longwall and the increased stress from the pillar is shown. Recommendations on the location of entries of the longwall panel when undermining the coal seam are made.
- Open Access
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1333 (3) , 032028
Computer modelling of a floor heave in coal mines
The paper presents results of numerical modeling of the longwall gateroad floor heave in the Taldinskaya-Zapadnaya-2 mine. The research is conducted using the finite element method. The research has shown that the floor heave can be reduced when using the relieve slots which are cut in two areas. The reasons and the mechanism of a floor heave of entries are considered. Influence of the major geological and mining factors is revealed. Recommendations about decrease in heave in entries of coal mines are made.
- 1 October 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1333 (3) , 032028
Open AccessComputer modelling of a floor heave in coal mines
The paper presents results of numerical modeling of the longwall gateroad floor heave in the Taldinskaya-Zapadnaya-2 mine. The research is conducted using the finite element method. The research has shown that the floor heave can be reduced when using the relieve slots which are cut in two areas. The reasons and the mechanism of a floor heave of entries are considered. Influence of the major geological and mining factors is revealed. Recommendations about decrease in heave in entries of coal mines are made.
- 27 August 2018
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 29-33
Prevention of gas-dynamic phenomena in floor rock mass in different variants of longwall mining at Belaruskali
The article presents findings of the research aimed to develop preventive measures for gas-dynamic phenomena caused in the floor of potash seam III by longwall mining at Belaruskali. The gas content and gas-dynamic characteristics of the potash seam floor rock mass were studied in conveyor, haulage, ventilation and backfill drifts. Boreholes were drilled at intervals and immediately sealed at a distance of 0.5 m from the mouth. Prevention designs were developed based on the result of the mine tests of gas content, gas-dynamic characteristics and time variation of free gas pressure in floor rocks in developing entries under different geotechnical conditions of longwall mining of potash seam III. The mine testing procedure provided quantitative assessment of such gas-dynamic characteristics of floor rocks as: free gas content, initial rate of gas release and free gas pressure. Taking into account the found mechanisms of initiation of gas-dynamic phenomena in mine floor, the methods and designs of preventive degassing drilling were worked out for developing entries in longwalls on the 1st, 2nd and 3rd layers of potash seam III under different geological and geotechnical conditions. The introduction of the preventive degassing drilling in the floor of developing entries in the listed longwalls improves operating safety in mines of Belaruskali.
- 27 August 2018
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 29-33
Prevention of gas-dynamic phenomena in floor rock mass in different variants of longwall mining at Belaruskali
The article presents findings of the research aimed to develop preventive measures for gas-dynamic phenomena caused in the floor of potash seam III by longwall mining at Belaruskali. The gas content and gas-dynamic characteristics of the potash seam floor rock mass were studied in conveyor, haulage, ventilation and backfill drifts. Boreholes were drilled at intervals and immediately sealed at a distance of 0.5 m from the mouth. Prevention designs were developed based on the result of the mine tests of gas content, gas-dynamic characteristics and time variation of free gas pressure in floor rocks in developing entries under different geotechnical conditions of longwall mining of potash seam III. The mine testing procedure provided quantitative assessment of such gas-dynamic characteristics of floor rocks as: free gas content, initial rate of gas release and free gas pressure. Taking into account the found mechanisms of initiation of gas-dynamic phenomena in mine floor, the methods and designs of preventive degassing drilling were worked out for developing entries in longwalls on the 1st, 2nd and 3rd layers of potash seam III under different geological and geotechnical conditions. The introduction of the preventive degassing drilling in the floor of developing entries in the listed longwalls improves operating safety in mines of Belaruskali.
- 30 July 2018
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 1,p. 3-8
Influence of face advance rate on geomechanical and gas-dynamic processes in longwalls in gassy mines
The article highlights currentness of studies into the influence of mine production rate on geomechanical and gas-dynamic processes in longwalls. It is shown that, despite the quick pace improvement in mining technique, there is essential backwardness of methodical and regulatory framework used to determine basic parameters of geomechanical and gas dynamic phenomena. The normative documents currently in force in Russia in calculating main roof caving steps in longwalls and the earlier research data on influence of longwall face advance rate on rock pressure phenomena in are analyzed. The research findings on undulating nature of change in methane content in high-production longwalls, which is related with movement processes in undermined rock mass, are examined. The field studies carried out in Zapolyarnaya Mine, Vorkutaugol reveal disagreement between the actual and calculated steps of main roof caving and recommend on improvement of the current calculation procedure. In Kotinskaya Mine, SUEK-Kuzbass, investigations of methane emission in longwalls determine the periodic nature of methane release maximums along a longwall panel. As the main causes of wide variation range of roof caving span (25–40 m), the authors show variable lithilogical composition and strength characteristics of roof rocks along longwall panels, significant range of output per face and the presence geological discontinuities. The future directions for research aimed to enhance safety and efficiency of high-production mining in series of gasbearing coal seams are defined. The authors express their deep gratitude to A. M. Cherdantsev, Chief Engineer, Yalevsky Mine, for the assistance in collection and processing of mine data, and for the participation in the research of influence of longwall face advance rate on geomechanical and gas-dynamic processes in longwall panels.
- 30 July 2018
- Published by Ore and Metals Publishing House in Eurasian Mining
- No. 1,p. 3-8
Influence of face advance rate on geomechanical and gas-dynamic processes in longwalls in gassy mines
The article highlights currentness of studies into the influence of mine production rate on geomechanical and gas-dynamic processes in longwalls. It is shown that, despite the quick pace improvement in mining technique, there is essential backwardness of methodical and regulatory framework used to determine basic parameters of geomechanical and gas dynamic phenomena. The normative documents currently in force in Russia in calculating main roof caving steps in longwalls and the earlier research data on influence of longwall face advance rate on rock pressure phenomena in are analyzed. The research findings on undulating nature of change in methane content in high-production longwalls, which is related with movement processes in undermined rock mass, are examined. The field studies carried out in Zapolyarnaya Mine, Vorkutaugol reveal disagreement between the actual and calculated steps of main roof caving and recommend on improvement of the current calculation procedure. In Kotinskaya Mine, SUEK-Kuzbass, investigations of methane emission in longwalls determine the periodic nature of methane release maximums along a longwall panel. As the main causes of wide variation range of roof caving span (25–40 m), the authors show variable lithilogical composition and strength characteristics of roof rocks along longwall panels, significant range of output per face and the presence geological discontinuities. The future directions for research aimed to enhance safety and efficiency of high-production mining in series of gasbearing coal seams are defined. The authors express their deep gratitude to A. M. Cherdantsev, Chief Engineer, Yalevsky Mine, for the assistance in collection and processing of mine data, and for the participation in the research of influence of longwall face advance rate on geomechanical and gas-dynamic processes in longwall panels.
- 29 January 2016
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 24-26
Improvement of selective potash extraction using shortwall mining with partial backfill
Productive potash salt strata of Starobinskoe deposit are composed of alternate barren rocks and productive layers of comparatively small thickness. Belaruskali extracts sylvinite with long-pillar, room-and-pillar and hybrid mining systems. The article shows the economical and environmental shortages of the listed systems and technologies at Starobinskoe potash salt deposit, due to considerable loss of minerals in support pillars and owing to ore dilution under joint output of sylvinite layers and halite partings (barren rock). The authors present the developed and patented technologies of selective extraction of ore from complex structure strata using broken halite for complete- or partial-mechanized backfilling. Mining is carried out with shortwall faces. Design and technology are exemplified for two variants of selective extraction and backfilling using self-propelled equipment. The proposed variants differ mainly in sequence of slicing in the rooms. As supplementary equipment, it is offered to use continuous miners allowing high production and having convenient height. Haulage and piling of broken halite partings of sylvinite layers is carried out by a self-propelled car to be emptied onto the floor of the neighbor worked-out rooms. The article gives evaluation of overall economical and environmental effect of the variants presented by the authors for selective extraction of productive layers. It is emphasized that backfill using broken halite is interesting from the viewpoint of scientific substantiation of feasible reduction in the size and number of support pillars, which will increase sylvinite extraction factor.
- 29 January 2016
- Published by Ore and Metals Publishing House in Gornyi Zhurnal
- p. 24-26
Improvement of selective potash extraction using shortwall mining with partial backfill
Productive potash salt strata of Starobinskoe deposit are composed of alternate barren rocks and productive layers of comparatively small thickness. Belaruskali extracts sylvinite with long-pillar, room-and-pillar and hybrid mining systems. The article shows the economical and environmental shortages of the listed systems and technologies at Starobinskoe potash salt deposit, due to considerable loss of minerals in support pillars and owing to ore dilution under joint output of sylvinite layers and halite partings (barren rock). The authors present the developed and patented technologies of selective extraction of ore from complex structure strata using broken halite for complete- or partial-mechanized backfilling. Mining is carried out with shortwall faces. Design and technology are exemplified for two variants of selective extraction and backfilling using self-propelled equipment. The proposed variants differ mainly in sequence of slicing in the rooms. As supplementary equipment, it is offered to use continuous miners allowing high production and having convenient height. Haulage and piling of broken halite partings of sylvinite layers is carried out by a self-propelled car to be emptied onto the floor of the neighbor worked-out rooms. The article gives evaluation of overall economical and environmental effect of the variants presented by the authors for selective extraction of productive layers. It is emphasized that backfill using broken halite is interesting from the viewpoint of scientific substantiation of feasible reduction in the size and number of support pillars, which will increase sylvinite extraction factor.