JNJiangang Niu

Jiangang Niu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Jiangang Niu has a total of 14 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Study on the Seismic Performance of Hollow Columns with Fiber Lightweight Aggregate Concrete

    by Ze-Hui Xiang, Jun Wang, Jian-Gang Niu, Yao Xu

    To study the seismic performance of hollow columns with fiber lightweight aggregate concrete, a quasi-static test on eight hollow columns with fiber lightweight aggregate concrete under lateral low-cycle reversed loading and axial force is presented in this article. The effects of the dosage of plastic-steel fibers (0, 3, 6 and 9 kg/m3, respectively), steel fibers (25, 50 and 75 kg/m3, respectively) and the axial compression ratio (0.4 and 0.6, respectively) on the seismic mechanical properties such as capacity under lateral load, stiffness, ductility and energy dissipation were investigated, and the main failure morphology and force mechanism of hollow columns with fiber lightweight aggregate concrete under lateral low-cycle reversed loading were revealed. The results showed that (1) the failure modes of hollow columns could be divided into shear failure, bending-shear failure and bending failure; (2) compared with the specimens without fiber, the increase in ductility coefficient of specimens with plastic-steel fiber was 2~33.7%, and that with steel fiber was 30.8~125.7%; the increase in cumulative energy dissipation of specimens with plastic-steel fiber was 5.3~43.7%, and that with steel fiber was 88.9~203.8%, thus indicating that the seismic performance of the specimens could be improved effectively via the incorporation of fibers. The formula of shear capacity under lateral load was proposed, and its calculation results were more reliable when compared with the actual project. A foundation for further research on the seismic performance of hollow columns with fiber lightweight aggregate concrete is provided.


  • Open Access

    Acoustic Emission Assessment of Corroded RC Columns Jointly Reinforced with Concrete Canvas and CFRP

    by Jingsong Wang, Jiangang Niu, Zehui Xiang, Jie Zhou, Jun Wang

    To explore the crack behaviors of corroded concrete columns jointly reinforced by concrete canvas (CC) and carbon fiber reinforced polymer (CFRP), a total of six specimen sets with different reinforcement forms and corrosion rates are designed and tested by acoustic emission (AE) technology. The assessed methods are AE characteristic parameters, RA-AF values, b values, and AE event spatial location map. The results show that the presence of CC changes the failure morphology of the specimen and improves the uneven deformation of concrete in the core area, which proves that the jointly reinforced method exhibits high plasticity deformation ability. The crack mode of the jointly reinforced specimen undergoes multiple transformations between tensile cracks and shear cracks, before ending in the final crush failure. The fluctuations in both amplitude and frequency of the b values of the jointly reinforced specimens increase significantly with time. The crack activity of concrete is more intense in this period, which proves that the jointly reinforced method ensures a more complete failure. Moreover, the increases in corrosion rate reduced the probability of shear cracks in the core concrete and further increased the failure degree of the specimen. The present study demonstrated that AE monitoring can effectively capture the characteristics of the cracking process of jointly reinforced concrete.


  • Open Access

    Experimental study on axial compression for composite hollow column of steel fiber, high-strength lightweight aggregate concrete and angle steel

    by Zehui Xiang, Dan Qiao, Jiangang Niu, Weiheng Liu

    In order to study the axial compression performance for composite hollow column of steel fiber, high-strength lightweight aggregate concrete and angle steel, the axial compression tests were carried out on five composite hollow columns of steel fiber, high-strength lightweight aggregate concrete and angle steel with the variation parameters of hollow ratio (0%, 15%, 16%, 32% and 36%) and the form of opening (round hole and square hole). The failure phenomena and failure forms of the specimens were observed, and their stress–strain curves were measured, and the axial bearing capacity formula suitable for composite hollow column of steel fiber, high-strength lightweight aggregate concrete and angle steel was established. The following conclusions may be obtained from the test results: the axial compression performance for the composite hollow columns of angle steel is influenced by the hollow ratio and opening form greatly. The axial compression performance for composite hollow columns of steel fiber, high-strength lightweight aggregate concrete and angle steel is almost close to that of composite solid columns when the hollow ratio is low; The higher the void ratio, the more the cracks at the surface of the concrete, some transverse cracks appear, the peak load decreases by about 5–38%, and the deformation ductility coefficient increases gradually; The deformation ductility coefficient of round-hole hollow column is lower than that of square-hole hollow column. Based on the test, the finite element software ABAQUS is used to simulate the SCAH column. The correctness of the model is verified via the comparison between the numerical simulation results and the test results. At the same time, the stress nephogram of concrete and steel at different stages and the stress nephogram at concrete restraint state are simulated. According to the finite element simulation results, Mander model is used to calculate the axial compression bearing capacity of composite hollow column of angle steel. The high calculation accuracy and suitable for popularization can be obtained.


  • Open Access

    Influence of Cross‐Sectional Shape on the Mechanical Properties of Concrete Canvas and CFRP‐Reinforced Columns

    by Jiangang Niu, Wenming Xu, Jingjun Li, Jian Liang

    Fiber‐reinforced polymer (FRP) wrapping has become an attractive strengthening technique for concrete columns. However, the ingress of corrosion into the concrete through the gap of CFRP fiber greatly reduces the durability of concrete and the bearing capacity of specimens. Concrete canvas, a kind of corrosion‐resistant and refractory material, is a promising method to enhance durability and carrying capacity. In this study, the concrete canvas (CC) and carbon fiber‐reinforced polymer (CFRP) were used to jointly reinforce columns with square cross section, octagonal cross section, circular cross section, and elliptical cross section. The influence of section shape on the strengthening effect of the axial compression column was investigated by the axial compression test. The results showed that the section shape had a significant influence on the reinforcement effect of the axial compression column. The carrying load capacity and ductility coefficient of different columns follow this order: square column < oval‐shaped columns < octagonal columns < circle columns. The increased amplitude of bearing capacity for the different columns with the increase of CC layers follows this order: square columns < oval‐shaped columns < circle column < octagonal columns. Compared with the unconstraint columns, the bearing capacity of adopting two‐layer CC columns increased by 129%, 155%, 150%, and 139% for the square, octagonal, circular, and elliptical columns, respectively. The octagonal column has the largest increase range. Compared with the unconstraint columns, the bearing capacity of adopting two‐layer CC columns increased by 348%, 318%, 310%, and 296% for the square, octagonal, elliptical, and circular columns, respectively. The square column has the largest increase range. The stress concentration phenomenon of all section shapes was weakened after the CC was used. The application of the CC on CFRP‐reinforced columns improves column ductility significantly, with some degree of increase in bearing capacity.