Anatoly M. Zhyzhaev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Anatoly M. Zhyzhaev has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Tatiana A. Zotina
Institute of Biophysics, Federal Research Center “Krasnoyarsk Science Center”, Siberian Branch of the Russian Academy of Sciences, Krasnoyarsk, Russia
2 shared publications A.A. Karacharov
1 shared publicationA.G. Mikhailov
1 shared publicationA.V. Baranov
1 shared publicationAlexander S. Samoilo
Scientific research engineering centre “Kristall”, Siberian Federal University, Krasnoyarsk, Russian Federation
1 shared publicationAnastasia V. Sirotina
Siberian Federal University, Krasnoyarsk 660041, Russia
1 shared publication
Latest Publications
- 14 July 2026
- Published by Elsevier in Minerals Engineering
- Vol. 248
Valleriite from the Norilsk ore District: Compositional and surface properties Controlling its flotation behavior
- 14 July 2026
- Published by Elsevier in Minerals Engineering
- Vol. 248
Valleriite from the Norilsk ore District: Compositional and surface properties Controlling its flotation behavior
- Open Access
- 8 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (12) , 5792
Study of the Composition and Structure of High-Strength Material Based on a Fine High-Calcium Fly Ash Using the SEM-EDS Method
This study examines the microspherical high-calcium fly ash (HCFA) and the high-strength binder material based on it by method of scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDS). The composition of 568 individual microspheres of the initial HCFA was determined and presented as ternary diagrams CaO–Al2O3–SiO2 and CaO–FeO–SiO2. The binder specimens have a compressive strength of 24–82 MPa at a curing time of 3–300 days. Their strength is close to that of CEM I 42.5N cement specimens with a curing time of up to 28 days, but exceeds it with a curing time of up to 300 days. The SEM-EDS method showed that the predominant composition of hydration products is concentrated in the high-calcium region of the CaO–Al2O3–SiO2 diagram with a CaO content of 60–80%. The SiO2 content in them is 15–30%, and their composition includes 1–15% Al2O3 and 5–14% FeO. It follows that the predominant products that provide the strength of the binder are calcium silicate hydrates with a CaO/SiO2 ratio of 1.7 to 4.2. The results contribute to the data for development of models for predicting the effect of HCFA on the properties of composite binders.
- 8 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (12) , 5792
Open AccessStudy of the Composition and Structure of High-Strength Material Based on a Fine High-Calcium Fly Ash Using the SEM-EDS Method
This study examines the microspherical high-calcium fly ash (HCFA) and the high-strength binder material based on it by method of scanning electron microscopy and energy-dispersive X-ray spectroscopy (SEM-EDS). The composition of 568 individual microspheres of the initial HCFA was determined and presented as ternary diagrams CaO–Al2O3–SiO2 and CaO–FeO–SiO2. The binder specimens have a compressive strength of 24–82 MPa at a curing time of 3–300 days. Their strength is close to that of CEM I 42.5N cement specimens with a curing time of up to 28 days, but exceeds it with a curing time of up to 300 days. The SEM-EDS method showed that the predominant composition of hydration products is concentrated in the high-calcium region of the CaO–Al2O3–SiO2 diagram with a CaO content of 60–80%. The SiO2 content in them is 15–30%, and their composition includes 1–15% Al2O3 and 5–14% FeO. It follows that the predominant products that provide the strength of the binder are calcium silicate hydrates with a CaO/SiO2 ratio of 1.7 to 4.2. The results contribute to the data for development of models for predicting the effect of HCFA on the properties of composite binders.
- 4 March 2026
- Published by Taylor & Francis in Grana
- Vol. 65 (1-2) , 12-28
Taxonomic relevance of pollen characteristics for several Ranunculus (section Batrachium , Ranunculaceae) species from western Siberia
Ranunculus L. section Batrachium DC. (hereafter Batrachium, water crowfoot) is a monophyletic group of aquatic plant species (Hörandl & Emadzade 2012). This section is considered taxonomically diff...
- 4 March 2026
- Published by Taylor & Francis in Grana
- Vol. 65 (1-2) , 12-28
Taxonomic relevance of pollen characteristics for several Ranunculus (section Batrachium , Ranunculaceae) species from western Siberia
Ranunculus L. section Batrachium DC. (hereafter Batrachium, water crowfoot) is a monophyletic group of aquatic plant species (Hörandl & Emadzade 2012). This section is considered taxonomically diff...
- 25 February 2026
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237 (10) , 609
Particulate Matter Retained by Aquatic Moss Provides a Means for Studying Radionuclide Transfer in a Large Siberian River
- 25 February 2026
- Published by Springer Nature in Water, Air, & Soil Pollution
- Vol. 237 (10) , 609
Particulate Matter Retained by Aquatic Moss Provides a Means for Studying Radionuclide Transfer in a Large Siberian River
- Open Access
- 17 October 2023
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- Vol. 29 (5) , 15-24
Production of nickel and cobalt metal powders under autoclave conditions
This paper presents the results of studies on the reduction of dispersed cobalt and nickel metal powders from their salts in ammonia-alkaline aqueous solutions under hydrothermal autoclave conditions. A unified and environmentally friendly method for producing these powders has been developed. Hydrazine hydrate, with a 25–50 % excess of the stoichiometric ratio, was used as a reducing agent. This choice allows for obtaining metal phases that are chemically uncontaminated by decomposition products. The experiments determined the conditions for the quantitative reduction of cobalt (II) and nickel (II) ions from ammonia-alkaline aqueous solutions. The synthesis temperature for the dispersed phases ranged from 110 to 155 °C. It has been demonstrated that under the conditions used, the process is completed quantitatively within 60 min. Metal concentrations in the solutions were determined using atomic absorption spectroscopy. The results of the X-ray phase analysis confirm that cobalt forms in the HCP lattice, while nickel forms in the FCC lattice. No other phases, including X-ray amorphous phases, were observed. It was found that with an increase in the hydrothermal synthesis temperature from 110 to 155 °C, the specific surface area of cobalt increased by more than 1.5 times, and that of nickel black powders increased by approximately 2 times. Scanning electron microscopy revealed that cobalt is formed in the shape of lamellar particles with a lateral size of about 500 nm and a thickness of 50 nm, which aggregate into fractal structures. Nickel is represented by spherical particles arranged in chain-like structures. Using X-ray photoelectron spectroscopy, it was determined that the surface of the materials is covered with oxidized forms. The surface atomic concentration of cobalt (0) was approximately 2 %, while that of nickel (0) was about 25 %.
- 17 October 2023
- Published by National University of Science and Technology MISiS in Izvestiya Vuzov. Tsvetnaya Metallurgiya (Proceedings of Higher Schools. Nonferrous Metallurgy)
- Vol. 29 (5) , 15-24
Open AccessProduction of nickel and cobalt metal powders under autoclave conditions
This paper presents the results of studies on the reduction of dispersed cobalt and nickel metal powders from their salts in ammonia-alkaline aqueous solutions under hydrothermal autoclave conditions. A unified and environmentally friendly method for producing these powders has been developed. Hydrazine hydrate, with a 25–50 % excess of the stoichiometric ratio, was used as a reducing agent. This choice allows for obtaining metal phases that are chemically uncontaminated by decomposition products. The experiments determined the conditions for the quantitative reduction of cobalt (II) and nickel (II) ions from ammonia-alkaline aqueous solutions. The synthesis temperature for the dispersed phases ranged from 110 to 155 °C. It has been demonstrated that under the conditions used, the process is completed quantitatively within 60 min. Metal concentrations in the solutions were determined using atomic absorption spectroscopy. The results of the X-ray phase analysis confirm that cobalt forms in the HCP lattice, while nickel forms in the FCC lattice. No other phases, including X-ray amorphous phases, were observed. It was found that with an increase in the hydrothermal synthesis temperature from 110 to 155 °C, the specific surface area of cobalt increased by more than 1.5 times, and that of nickel black powders increased by approximately 2 times. Scanning electron microscopy revealed that cobalt is formed in the shape of lamellar particles with a lateral size of about 500 nm and a thickness of 50 nm, which aggregate into fractal structures. Nickel is represented by spherical particles arranged in chain-like structures. Using X-ray photoelectron spectroscopy, it was determined that the surface of the materials is covered with oxidized forms. The surface atomic concentration of cobalt (0) was approximately 2 %, while that of nickel (0) was about 25 %.
- 15 February 2018
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 53 (11) , 1654-1665
Biosorbents based on pine sawdust and malt sprouts for preconcentration and ICP-OES determination of nonferrous, heavy, and precious metals in the environmental samples
Pine sawdust and malt sprouts modified with orthophosphoric acid and carbamide have been proposed for solid-phase extraction (SPE) of nonferrous, heavy, and precious metals and their subsequent determination in the environmental samples by inductively coupled plasma optical emission spectrometry (ICP-OES). Modified adsorbents were characterized by SEM, TGA, and FT-IR and compared with native matrixes. SPE of some nonferrous and precious metal ions by biosorbents was studied. Depending on the SPE conditions, it was possible to separate nonferrous and heavy metals from alkali and alkaline earth metals. The proposed adsorbents are effective for preconcentration of nonferrous and heavy metals from natural waters and precious metals from solutions after digestion of geological samples.
- 15 February 2018
- Published by Taylor & Francis in Separation Science and Technology
- Vol. 53 (11) , 1654-1665
Biosorbents based on pine sawdust and malt sprouts for preconcentration and ICP-OES determination of nonferrous, heavy, and precious metals in the environmental samples
Pine sawdust and malt sprouts modified with orthophosphoric acid and carbamide have been proposed for solid-phase extraction (SPE) of nonferrous, heavy, and precious metals and their subsequent determination in the environmental samples by inductively coupled plasma optical emission spectrometry (ICP-OES). Modified adsorbents were characterized by SEM, TGA, and FT-IR and compared with native matrixes. SPE of some nonferrous and precious metal ions by biosorbents was studied. Depending on the SPE conditions, it was possible to separate nonferrous and heavy metals from alkali and alkaline earth metals. The proposed adsorbents are effective for preconcentration of nonferrous and heavy metals from natural waters and precious metals from solutions after digestion of geological samples.
- 25 August 2011
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 27 (18) , 11697-11703
Formation of Bimetallic Au–Pd and Au–Pt Nanoparticles under Hydrothermal Conditions and Microwave Irradiation
The reduction of chlorocomplexes of gold(III) from muriatic solutions by nanocrystal powders of palladium and platinum at 110 and 130 °C under hydrothermal conditions and the action of microwave irradiation has been investigated. The structure and composition of the solid phase have been characterized by transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and chemical methods. Bimetallic particles with a core–shell structure have been revealed. The obtained particles are established to have a core of the metal reductant covered with a substitutional solid (Au, Pd) solution in case of palladium, and isolated by a gold layer in the case of platinum. The main reason for such a difference is the ratio between the rates of aggregation and reduction. It has been shown by the example of the Au–Pd system that the use of microwave irradiation allows us not only to accelerate the synthesis of particles but also to obtain more homogeneous materials in comparison with conventional heating.
- 25 August 2011
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 27 (18) , 11697-11703
Formation of Bimetallic Au–Pd and Au–Pt Nanoparticles under Hydrothermal Conditions and Microwave Irradiation
The reduction of chlorocomplexes of gold(III) from muriatic solutions by nanocrystal powders of palladium and platinum at 110 and 130 °C under hydrothermal conditions and the action of microwave irradiation has been investigated. The structure and composition of the solid phase have been characterized by transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and chemical methods. Bimetallic particles with a core–shell structure have been revealed. The obtained particles are established to have a core of the metal reductant covered with a substitutional solid (Au, Pd) solution in case of palladium, and isolated by a gold layer in the case of platinum. The main reason for such a difference is the ratio between the rates of aggregation and reduction. It has been shown by the example of the Au–Pd system that the use of microwave irradiation allows us not only to accelerate the synthesis of particles but also to obtain more homogeneous materials in comparison with conventional heating.