Ilham Nassar-Eddine
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ilham Nassar-Eddine has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Youssef Errami
Chouaib Doukkali University
7 shared publications Abdellatif Obbadi
Chouaib Doukkali University, Morocco
6 shared publicationsAbdelkrim El Fajri
Chouaib Doukkali University, Morocco
5 shared publicationsSmail Sahnoun
Chouaib Doukkali University, Morocco
5 shared publicationsKarima Et-Torabi
Laboratory of Electronics, Instrumentation and Energy Faculty of Science, El-jadida, Moroccoo
4 shared publicationsMustapha Agunaou
Laboratory of Electronics, Instrumentation and Energy Faculty of Science, El-jadida, Moroccoo
4 shared publications
Latest Publications
- Open Access
- 23 October 2019
- Published by Association for Computing Machinery (ACM)
- p. 1-8
A Robust Control based on Fuzzy Logic Approach of a Single-Stage Grid-Connected PV System
- 23 October 2019
- Published by Association for Computing Machinery (ACM)
- p. 1-8
Open AccessA Robust Control based on Fuzzy Logic Approach of a Single-Stage Grid-Connected PV System
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
An accurate method for parameters determination of current voltage characteristics of photovoltaic modules
The solar power conversion capacity and the output performance of photovoltaic devices, depend mainly on the electrical characteristics of the cell, the module or the array. Therefore, knowing precisely the current versus voltage characteristics remains essential to perform the productivity as well as the solar efficiency of these devices. Researchers presented several methods, but the precise determination of the PV cell parameters remains a challenge. In this paper, we describe with rigorous way an analytical and simple method giving directly the expression of the photocurrent, the diode reverse saturation current, the shunt resistance, the series resistance and the ideality factor for a one exponential model. The three points usually used, at short circuit current, the maximum power and at open circuit, give four equations for the determination of unknown parameters. The fifth equation is at the point corresponding to half of the short circuit current. These equations are reduced to two nonlinear equations with two unknown parameters easily solved by the MathCAD software. The test of a polycrystalline Pv module is performed in a laboratory, the numerical values obtained give the best results compared to some previous methods and show a minimal error. A study about temperature effect on the all parameters was also made and shows a good conformity with the theoretical models, which proof the accuracy of the method.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
An accurate method for parameters determination of current voltage characteristics of photovoltaic modules
The solar power conversion capacity and the output performance of photovoltaic devices, depend mainly on the electrical characteristics of the cell, the module or the array. Therefore, knowing precisely the current versus voltage characteristics remains essential to perform the productivity as well as the solar efficiency of these devices. Researchers presented several methods, but the precise determination of the PV cell parameters remains a challenge. In this paper, we describe with rigorous way an analytical and simple method giving directly the expression of the photocurrent, the diode reverse saturation current, the shunt resistance, the series resistance and the ideality factor for a one exponential model. The three points usually used, at short circuit current, the maximum power and at open circuit, give four equations for the determination of unknown parameters. The fifth equation is at the point corresponding to half of the short circuit current. These equations are reduced to two nonlinear equations with two unknown parameters easily solved by the MathCAD software. The test of a polycrystalline Pv module is performed in a laboratory, the numerical values obtained give the best results compared to some previous methods and show a minimal error. A study about temperature effect on the all parameters was also made and shows a good conformity with the theoretical models, which proof the accuracy of the method.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A new Fuzzy Logic architecture to control the DC-bus voltage in grid connected photovoltaic system
The control strategy’ efficiency of single stage grid-connected PV system is important. This study suggest a novel Fuzzy logic controller to control and regulate the DC-bus voltage at its reference value under changing irradiance levels. Moreover, a fuzzy logic algorithm is employed to extract the maximum power from the photovoltaic array and to provide the reference value of DC-bus voltage. Thus, a comparative analysis between the proposed and proportional integral controllers is made to prove the effectiveness of the developed controller. Furthermore, to validate the superiority of the proposed Fuzzy Logic controller, simulations were carried out at Matlab/Simulink environment. Finally, the simulation results prove that the proposed controller gives better performance in response time, rate of overshoot and tracking efficiency regarding the proportional integral controller. In addition, a comparison in term of Total Harmonic Distortion of current is asses, it demonstrate that the control strategy with the developed Fuzzy Logic gives less value compared to that with the PI controller.
- 1 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
A new Fuzzy Logic architecture to control the DC-bus voltage in grid connected photovoltaic system
The control strategy’ efficiency of single stage grid-connected PV system is important. This study suggest a novel Fuzzy logic controller to control and regulate the DC-bus voltage at its reference value under changing irradiance levels. Moreover, a fuzzy logic algorithm is employed to extract the maximum power from the photovoltaic array and to provide the reference value of DC-bus voltage. Thus, a comparative analysis between the proposed and proportional integral controllers is made to prove the effectiveness of the developed controller. Furthermore, to validate the superiority of the proposed Fuzzy Logic controller, simulations were carried out at Matlab/Simulink environment. Finally, the simulation results prove that the proposed controller gives better performance in response time, rate of overshoot and tracking efficiency regarding the proportional integral controller. In addition, a comparison in term of Total Harmonic Distortion of current is asses, it demonstrate that the control strategy with the developed Fuzzy Logic gives less value compared to that with the PI controller.
- 1 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Parameter Identification of Multicrystalline Modules Using Two Methods and Five Improved Mathematical Models
The present work suggests an accurate comparison of two methods for estimating the five physical parameters of photovoltaic (PV) multiycrystalline module from its manufacturer's datasheet, using a single diode model. The estimation methods used are the iterative method based on the Newton Raphson, and the analytical method based on the Lambert W function. The used methods are applied for multiycrystalline PV module to check the accuracy of these methods. The implementation of five improved mathematical models is required, to estimate the unknown parameters of multiycrystalline module under real operating conditions. The current absolute error (AE) is used to validate the accuracy of the improved models. Finally, the root mean square deviation (RMSD) and its normalized value (NRMSD), are calculated using three methods already existing in the literature, are also calculated by the two methods used in this study to prove the effectiveness of the used methods. The results confirm that the measured data is similar to improved models' curves. It is then found that the used methods are more accurate than the existing ones. Moreover, the results indicate that all models combined with iterative method are the most adaptable for the multicrystalline modules.
- 1 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Parameter Identification of Multicrystalline Modules Using Two Methods and Five Improved Mathematical Models
The present work suggests an accurate comparison of two methods for estimating the five physical parameters of photovoltaic (PV) multiycrystalline module from its manufacturer's datasheet, using a single diode model. The estimation methods used are the iterative method based on the Newton Raphson, and the analytical method based on the Lambert W function. The used methods are applied for multiycrystalline PV module to check the accuracy of these methods. The implementation of five improved mathematical models is required, to estimate the unknown parameters of multiycrystalline module under real operating conditions. The current absolute error (AE) is used to validate the accuracy of the improved models. Finally, the root mean square deviation (RMSD) and its normalized value (NRMSD), are calculated using three methods already existing in the literature, are also calculated by the two methods used in this study to prove the effectiveness of the used methods. The results confirm that the measured data is similar to improved models' curves. It is then found that the used methods are more accurate than the existing ones. Moreover, the results indicate that all models combined with iterative method are the most adaptable for the multicrystalline modules.
- 1 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Photovoltaic Parameter Extraction Methods for Single and Double Diode Models under Real Changing Environmental Conditions
This paper compares two methods for extraction of photovoltaic (PV) module parameters. The numerical method called Gauss-Seidel, used on the single diode model, and the analytical method applied on the double diode model. Both methods are based on the manufacturer's datasheets to extract the five parameters. These methods are validated using monocrystalline PV module. The modified mathematical modeling equations are classified into models 1 to 5. Only model 2 and model 4 are used for the analytical method. Each model is based on the different combinations of the ideality factor, the series resistance, photocurrent and saturation current plotted under varying temperature and irradiance. The accuracy of PV module based on both methods is evaluated by Absolute Error (AE). In order to evaluate the effectiveness and accuracy of the proposed methods, the equations were implemented in the MATLAB/Simulink environment and the results obtained are compared with extracted experimental data.
- 1 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Photovoltaic Parameter Extraction Methods for Single and Double Diode Models under Real Changing Environmental Conditions
This paper compares two methods for extraction of photovoltaic (PV) module parameters. The numerical method called Gauss-Seidel, used on the single diode model, and the analytical method applied on the double diode model. Both methods are based on the manufacturer's datasheets to extract the five parameters. These methods are validated using monocrystalline PV module. The modified mathematical modeling equations are classified into models 1 to 5. Only model 2 and model 4 are used for the analytical method. Each model is based on the different combinations of the ideality factor, the series resistance, photocurrent and saturation current plotted under varying temperature and irradiance. The accuracy of PV module based on both methods is evaluated by Absolute Error (AE). In order to evaluate the effectiveness and accuracy of the proposed methods, the equations were implemented in the MATLAB/Simulink environment and the results obtained are compared with extracted experimental data.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Parameter Extraction Methods of Thin Film Photovoltaic Panel using Five Enhanced Models
In this work, a comparative study of two parameter extraction methods: an iterative method based on Newton Raphson algorithm and an analytical method based on Lambert W function is presented. They are also tested on ST40 thin film photovoltaic (PV) panel. For both methods, five enhanced mathematical models are implemented to extract the parameters of this PV panel under varying environmental conditions. In order to validate the accuracy of the five models, the results of the models' simulation are compared with the measured data using the RMSE and AE. Then, the results of both methods are evaluated so as to ascertain which of them are more accurate. The results reported in this paper confirm that the models' simulation shows good agreement with the measured data. It is found that the analytical method with all five models is the most suitable for the thin film panel.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Parameter Extraction Methods of Thin Film Photovoltaic Panel using Five Enhanced Models
In this work, a comparative study of two parameter extraction methods: an iterative method based on Newton Raphson algorithm and an analytical method based on Lambert W function is presented. They are also tested on ST40 thin film photovoltaic (PV) panel. For both methods, five enhanced mathematical models are implemented to extract the parameters of this PV panel under varying environmental conditions. In order to validate the accuracy of the five models, the results of the models' simulation are compared with the measured data using the RMSE and AE. Then, the results of both methods are evaluated so as to ascertain which of them are more accurate. The results reported in this paper confirm that the models' simulation shows good agreement with the measured data. It is found that the analytical method with all five models is the most suitable for the thin film panel.
- 1 September 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 148, 1041-1054
Parameters estimation of the single and double diode photovoltaic models using a Gauss–Seidel algorithm and analytical method: A comparative study
- 1 September 2017
- Published by Elsevier in Energy Conversion and Management
- Vol. 148, 1041-1054
Parameters estimation of the single and double diode photovoltaic models using a Gauss–Seidel algorithm and analytical method: A comparative study
- 1 July 2016
- Published by Elsevier in Energy Conversion and Management
- Vol. 119, 37-48
Parameter estimation of photovoltaic modules using iterative method and the Lambert W function: A comparative study
- 1 July 2016
- Published by Elsevier in Energy Conversion and Management
- Vol. 119, 37-48
Parameter estimation of photovoltaic modules using iterative method and the Lambert W function: A comparative study