Abdelrahman Farghali
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Abdelrahman Farghali has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Tatsuhiko Aizawa
4 shared publications- Junho Choi
Department of Mechanical Engineering, Tokyo City University, Tokyo 158-8557, Japan
2 shared publications Hiroshi Tamagaki
Takasago-City Japan Hyougo 2-3-1 Nii-Hama, Arai 676-8670
1 shared publicationJongduk Kim
Park Systems Japan Inc., 1-17-1 Kanda-Nishikicho, Tokyo , Chiyoda-ku, 101-0054, JAPAN
1 shared publicationKazutoki Iwasa
Department of Mechanical Engineering, The University of Tokyo, 7-3-1 Hongo, Bunkyo-ku, Bunkyo-ku, Tokyo, 113-0033, JAPAN
1 shared publicationKenji Wasa
Tokyo Japan 4-3-4 Shibaura, Minato-City 108-0023
1 shared publication
Latest Publications
- Open Access
- 5 December 2025
- Published by Elsevier in Results in Materials
- Vol. 29
Molecular dynamics study on homogeneous and heterogeneous nanostructuring in massive nitrogen supersaturation into FCC-structured iron
- 5 December 2025
- Published by Elsevier in Results in Materials
- Vol. 29
Open AccessMolecular dynamics study on homogeneous and heterogeneous nanostructuring in massive nitrogen supersaturation into FCC-structured iron
- Open Access
- 26 July 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 57 (45) , 455202
Atomic scale smoothing of nanoscale quartz mold using amorphous carbon films
Surface roughness control of end products is increasingly becoming significant, especially with the miniaturization trends in the semiconductor industry. Ultra-thin amorphous carbon (a-C) films offer a prime solution to optimize surface roughness due to their outstanding characteristics. In this study, hydrogenated a-C films are deposited on two-dimensional quartz plates and three-dimensional quartz molds to evaluate the growth mechanisms and changes in the surface roughness, which is supported by molecular dynamics simulations. Results reveal that surface roughness encounters multiple variations until it reaches stable values. These fluctuations are categorized into four different stages which provide a concrete understanding of various growing mechanisms at each stage. Different behavior of the atoms in the top layers is recorded in the cases of normal and grazing incidents of carbon atoms. Lower surface roughness values are obtained at low-angle deposition. Interestingly, surface smoothing is attained on the sidewalls of the nanotrench mold where the deposition occurs with high incident ion angles.
- 26 July 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 57 (45) , 455202
Open AccessAtomic scale smoothing of nanoscale quartz mold using amorphous carbon films
Surface roughness control of end products is increasingly becoming significant, especially with the miniaturization trends in the semiconductor industry. Ultra-thin amorphous carbon (a-C) films offer a prime solution to optimize surface roughness due to their outstanding characteristics. In this study, hydrogenated a-C films are deposited on two-dimensional quartz plates and three-dimensional quartz molds to evaluate the growth mechanisms and changes in the surface roughness, which is supported by molecular dynamics simulations. Results reveal that surface roughness encounters multiple variations until it reaches stable values. These fluctuations are categorized into four different stages which provide a concrete understanding of various growing mechanisms at each stage. Different behavior of the atoms in the top layers is recorded in the cases of normal and grazing incidents of carbon atoms. Lower surface roughness values are obtained at low-angle deposition. Interestingly, surface smoothing is attained on the sidewalls of the nanotrench mold where the deposition occurs with high incident ion angles.
- Open Access
Microstructure/Mechanical Characterization of Plasma Nitrided Fine-Grain Austenitic Stainless Steels in Low Temperature
Fine-grained austenitic stainless steels (FGSS) were plasma nitrided below 700 K to describe their microstructure evolution during the nitrogen supersaturation process and to investigate the post-stressing effect on the microstructure and mechanical properties of nitrided FGSS. Normal- and fine-grained AISI304 plates were nitrided at 623 K and 673 K to investigate the grain size effect on the nitrogen supersaturation process as well as the microstructure evolution during the nitriding process. Fine-grained AISI316 (FGSS316) wires were nitrided at 623 K to demonstrate that their outer surfaces were uniformly nitrided to have the same two-phase, refined microstructure with high nitrogen solute content. This nitrided FGSS316 wire had a core structure where the original FGSS316 core matrix was bound by the nitrided FGSS316 layer. The nitrided wire had higher stiffness, ultimate strength, and elongation in the uniaxial tensile testing than its un-nitrided wires. The core microstructure was refined and homogenized by this applied loading together with an increase of nitrided layer hardness.
Open AccessMicrostructure/Mechanical Characterization of Plasma Nitrided Fine-Grain Austenitic Stainless Steels in Low Temperature
Fine-grained austenitic stainless steels (FGSS) were plasma nitrided below 700 K to describe their microstructure evolution during the nitrogen supersaturation process and to investigate the post-stressing effect on the microstructure and mechanical properties of nitrided FGSS. Normal- and fine-grained AISI304 plates were nitrided at 623 K and 673 K to investigate the grain size effect on the nitrogen supersaturation process as well as the microstructure evolution during the nitriding process. Fine-grained AISI316 (FGSS316) wires were nitrided at 623 K to demonstrate that their outer surfaces were uniformly nitrided to have the same two-phase, refined microstructure with high nitrogen solute content. This nitrided FGSS316 wire had a core structure where the original FGSS316 core matrix was bound by the nitrided FGSS316 layer. The nitrided wire had higher stiffness, ultimate strength, and elongation in the uniaxial tensile testing than its un-nitrided wires. The core microstructure was refined and homogenized by this applied loading together with an increase of nitrided layer hardness.
- 1 April 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 920, 161-166
Plasma Printing of Micro-Punch Assembly for Micro-Embossing of Aluminum Sheets
This paper concerned with micro-embossing of micro-cavities and micro-grooves into aluminum sheets by CNC-stamping with use of the arrayed DLC multi-punches. Both SKD11 and AISI420 steel die substrates were prepared and DLC-coated with the thickness of 10 to 15 μm. This DLC coating worked as a punch material. The two dimensional micro-patterns were printed onto this DLC film by maskless lithography. The unprinted DLC films were removed by the plasma oxidation to leave the three dimensional DLC-punch array on the steel substrate. This micro-pillared and micro-grooved DLC-punches were placed into the cassette die set for micro-embossing process by using the table-top CNC stamper. The micro-circular patterns transformed to the micro-pillars in the DLC punch by the plasma oxidation. Through the CNC-micro-embossing, this micro-texture further transferred to micro-cavities in the aluminum sheet. The dimensional accuracy of embossed micro-textures by stamping was measured by SEM and three dimensional profilometer with comparison to the tailored micro-pattern and the DLC-punch array configuration.
- 1 April 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 920, 161-166
Plasma Printing of Micro-Punch Assembly for Micro-Embossing of Aluminum Sheets
This paper concerned with micro-embossing of micro-cavities and micro-grooves into aluminum sheets by CNC-stamping with use of the arrayed DLC multi-punches. Both SKD11 and AISI420 steel die substrates were prepared and DLC-coated with the thickness of 10 to 15 μm. This DLC coating worked as a punch material. The two dimensional micro-patterns were printed onto this DLC film by maskless lithography. The unprinted DLC films were removed by the plasma oxidation to leave the three dimensional DLC-punch array on the steel substrate. This micro-pillared and micro-grooved DLC-punches were placed into the cassette die set for micro-embossing process by using the table-top CNC stamper. The micro-circular patterns transformed to the micro-pillars in the DLC punch by the plasma oxidation. Through the CNC-micro-embossing, this micro-texture further transferred to micro-cavities in the aluminum sheet. The dimensional accuracy of embossed micro-textures by stamping was measured by SEM and three dimensional profilometer with comparison to the tailored micro-pattern and the DLC-punch array configuration.
- 1 January 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (3) , 401-407
Nitrogen Supersaturation Process in the AISI420 Martensitic Stainless Steels by Low Temperature Plasma Nitriding
- 1 January 2018
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 58 (3) , 401-407
Nitrogen Supersaturation Process in the AISI420 Martensitic Stainless Steels by Low Temperature Plasma Nitriding
- 1 January 2017
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 58 (4) , 697-700
Phase Transformation Induced by High Nitrogen Content Solid Solution in the Martensitic Stainless Steels
- 1 January 2017
- Published by Japan Institute of Metals in MATERIALS TRANSACTIONS
- Vol. 58 (4) , 697-700
Phase Transformation Induced by High Nitrogen Content Solid Solution in the Martensitic Stainless Steels