Xiangxin Xue
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiangxin Xue has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Songtao Yang
School of Materials and Metallurgy, University of Science and Technology Liaoning, Anshan 114051, China
2 shared publications - Mi Zhou
School of Metallurgy, Northeastern University, Shenyang 110819, China
1 shared publication - Tao Jiang
School of Metallurgy, Northeastern University, Shenyang 110819, China
1 shared publication - Weidong Tang
School of Metallurgy, Northeastern University, Shenyang 110819, China
1 shared publication
Latest Publications
- Open Access
Effect of TiO2 on the Sintering Behavior of Low-Grade Vanadiferous Titanomagnetite Ore
Low-grade vanadiferous titanomagnetite ore (LVTM) is as an important mineral resource for sintering ore manufacturing. Furthermore, TiO2 has a significant effect on the sintering process of iron ore fines. The effects of TiO2 on the metallurgical properties, microstructure, and mineral composition of LVTM sinter were investigated by sintering pot tests, X-ray diffraction (XRD), scanning electron microscopy (SEM), and mineral phase microanalysis. The results were as follows: as the TiO2 content increased from 1.75% to 4.55%, the flame front speed and productivity decreased, while the reduction degradation index (RDI) and softening properties deteriorated. In addition, the tumbler index (TI) values reached a maximum at TiO2 = 1.75%. In addition, with increasing TiO2 content, an increase in the magnetite and perovskite phase, and a decrease in calcium ferrite and hematite were found with an increase in TiO2 content. Thus, the lower the TiO2 content, the better the quality of the sinter.
Open AccessEffect of TiO2 on the Sintering Behavior of Low-Grade Vanadiferous Titanomagnetite Ore
Low-grade vanadiferous titanomagnetite ore (LVTM) is as an important mineral resource for sintering ore manufacturing. Furthermore, TiO2 has a significant effect on the sintering process of iron ore fines. The effects of TiO2 on the metallurgical properties, microstructure, and mineral composition of LVTM sinter were investigated by sintering pot tests, X-ray diffraction (XRD), scanning electron microscopy (SEM), and mineral phase microanalysis. The results were as follows: as the TiO2 content increased from 1.75% to 4.55%, the flame front speed and productivity decreased, while the reduction degradation index (RDI) and softening properties deteriorated. In addition, the tumbler index (TI) values reached a maximum at TiO2 = 1.75%. In addition, with increasing TiO2 content, an increase in the magnetite and perovskite phase, and a decrease in calcium ferrite and hematite were found with an increase in TiO2 content. Thus, the lower the TiO2 content, the better the quality of the sinter.
- Open Access
Study on Sintering Characteristics of Ultra-Poor Vanadium-Titanium Magnetite
Artificial rich ore for blast furnace use can be produced by sintering ultra-poor vanadium-titanium magnetite (PVTM) with a high-grade iron concentrate. Here, acid (R = 0.33, 0.50), self-fluxing (R = 1.10), and high-basicity (R = 2.60) PVTM sinters were produced in a sinter pot. Their performances were determined using the comprehensive index. The microstructures of the PVTM sinter were observed by metallographic microscope and scanning electron microscopy equipped with an energy dispersion spectrum (SEM-EDS). The results suggest that the acid PVTM sinter had a low flame front speed, low productivity, an uneven size distribution, and poor softening properties. It did have a high tumble index (TI) and low-temperature reduction disintegration index (RDI). The self-fluxing PVTM sinter had the worst performance (TI, RDI, reducibility index (RI)), while the high-basicity PVTM sinter had the highest flame front speed, highest productivity, a reasonable size distribution, excellent softening properties, and satisfactory TI and RDI values. The main consolidation form of the acid sinter was crystal stock, the main bonding phase of the self-fluxing sinter was silicate, and the main bonding phase of the high-basicity sinter was silico-ferrite of calcium and aluminum (SFCA). The comprehensive index values (from high to low) were the high-basicity (R = 2.60), acid (R = 0.50), natural acid (R = 0.33), and self-fluxing (R = 1.10) PVTM sinters. When the production capacity of the acid pellet was in shortage, the acid PVTM sinter (R = 0.50) could be produced by the surplus from the sinter plant. This replaced a part of the acid pellet and the burden structural model of the blast furnace smelting vanadium so the titanium burden could adopt a ‘high-basicity PVTM sinter + acid V-Ti pellet + acid (R = 0.50) PVTM sinter’.
Open AccessStudy on Sintering Characteristics of Ultra-Poor Vanadium-Titanium Magnetite
Artificial rich ore for blast furnace use can be produced by sintering ultra-poor vanadium-titanium magnetite (PVTM) with a high-grade iron concentrate. Here, acid (R = 0.33, 0.50), self-fluxing (R = 1.10), and high-basicity (R = 2.60) PVTM sinters were produced in a sinter pot. Their performances were determined using the comprehensive index. The microstructures of the PVTM sinter were observed by metallographic microscope and scanning electron microscopy equipped with an energy dispersion spectrum (SEM-EDS). The results suggest that the acid PVTM sinter had a low flame front speed, low productivity, an uneven size distribution, and poor softening properties. It did have a high tumble index (TI) and low-temperature reduction disintegration index (RDI). The self-fluxing PVTM sinter had the worst performance (TI, RDI, reducibility index (RI)), while the high-basicity PVTM sinter had the highest flame front speed, highest productivity, a reasonable size distribution, excellent softening properties, and satisfactory TI and RDI values. The main consolidation form of the acid sinter was crystal stock, the main bonding phase of the self-fluxing sinter was silicate, and the main bonding phase of the high-basicity sinter was silico-ferrite of calcium and aluminum (SFCA). The comprehensive index values (from high to low) were the high-basicity (R = 2.60), acid (R = 0.50), natural acid (R = 0.33), and self-fluxing (R = 1.10) PVTM sinters. When the production capacity of the acid pellet was in shortage, the acid PVTM sinter (R = 0.50) could be produced by the surplus from the sinter plant. This replaced a part of the acid pellet and the burden structural model of the blast furnace smelting vanadium so the titanium burden could adopt a ‘high-basicity PVTM sinter + acid V-Ti pellet + acid (R = 0.50) PVTM sinter’.