Silvana Borcănescu
Silvana Borcănescu has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Alexandru Popa
Institute of Chemistry Timişoara, Timisoara, Romania
6 shared publications - Orsina Verdes
“Coriolan Drăgulescu” Institute of Chemistry, Bv. Mihai Viteazul, No. 24, 300223 Timisoara, Romania
5 shared publications - Mariana Suba
“Coriolan Dragulescu” Institute of Chemistry, Romanian Academy, Mihai Viteazu No. 24, 300223 Timișoara, Romania
4 shared publications - Robert Ianoş
“Politehnica” University of Timişoara
4 shared publications Radu Lazău
3 shared publicationsMariana Suba
2 shared publications
Latest Publications
- Open Access
Effect of Temperature on CO2 Adsorption onto Amine-Functionalized KIT-6 Adsorbents
The mesoporous silica KIT-6 was synthesized and functionalized with 3-aminopropyltriethoxysilane (APTES) by grafting at 110 °C. The composites were prepared with three different concentrations of APTES: 20, 30 and 40 wt.%. The as-prepared samples were characterized by thermal gravimetric analysis in air and nitrogen atmosphere (TG/DTA), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction and nitrogen adsorption–desorption. In this study, CO2 adsorption–desorption was investigated using temperature programmed desorption mass spectrometry (TPD-MS) at different temperatures. The adsorption capacity of the prepared composites is 2.23 mmol CO2/g at 40 °C and decreases to 0.95 mmol/g at 70 °C. Regarding the efficiency of the amino groups, the best result was obtained for APTES-grafted KIT-6 at 40 °C, with 0.512 mmol CO2/mmol NH2. The results showed good cyclical stability in adsorption capacities even after nine adsorption–desorption cycles.
Open AccessEffect of Temperature on CO2 Adsorption onto Amine-Functionalized KIT-6 Adsorbents
The mesoporous silica KIT-6 was synthesized and functionalized with 3-aminopropyltriethoxysilane (APTES) by grafting at 110 °C. The composites were prepared with three different concentrations of APTES: 20, 30 and 40 wt.%. The as-prepared samples were characterized by thermal gravimetric analysis in air and nitrogen atmosphere (TG/DTA), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction and nitrogen adsorption–desorption. In this study, CO2 adsorption–desorption was investigated using temperature programmed desorption mass spectrometry (TPD-MS) at different temperatures. The adsorption capacity of the prepared composites is 2.23 mmol CO2/g at 40 °C and decreases to 0.95 mmol/g at 70 °C. Regarding the efficiency of the amino groups, the best result was obtained for APTES-grafted KIT-6 at 40 °C, with 0.512 mmol CO2/mmol NH2. The results showed good cyclical stability in adsorption capacities even after nine adsorption–desorption cycles.
- Open Access
- 19 June 2023
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 24 (12) , 10345
Functionalized Ordered Mesoporous MCM-48 Silica: Synthesis, Characterization and Adsorbent for CO2 Capture
The ordered mesoporous silica MCM-48 with cubic Ia3d structure was synthesized using the cationic surfactant hexadecyltrimethylammonium bromide (CTAB) as a template agent and tetraethylorthosilicate (TEOS) as a silica source. The obtained material was first functionalized with (3-glycidyloxypropyl)trimethoxysilane (KH560); further, two types of amination reagents were used: ethylene diamine (N2) and diethylene triamine (N3). The modified amino-functionalized materials were characterized by powder X-ray diffraction (XRD) at low angles, infrared spectroscopy (FT-IR) and nitrogen adsorption–desorption experiments at 77 K. Characterization from a structural point of view reveals that the ordered MCM-48 mesoporous silica has a highly ordered structure and a large surface area (1466.059 m2/g) and pore volume (0.802 cm3/g). The amino-functionalized MCM-48 molecular sieves were tested for CO2 adsorption–desorption properties at different temperatures using thermal program desorption (TPD). Promising results for CO2 adsorption capacities were achieved for MCM-48 sil KH560-N3 at 30 °C. At 30 °C, the MCM-48 sil KH560-N3 sample has an adsorption capacity of 3.17 mmol CO2/g SiO2, and an efficiency of amino groups of 0.58 mmol CO2/mmolNH2. After nine adsorption–desorption cycles, the results suggest that the performance of the MCM-48 sil KH N2 and MCM-48 sil KH N3 adsorbents is relatively stable, presenting a low decrease in the adsorption capacity. The results reported in this paper for the investigated amino-functionalized molecular sieves as absorbents for CO2 can be considered as promising.
- 19 June 2023
- Published by MDPI AG in International Journal of Molecular Sciences
- Vol. 24 (12) , 10345
Open AccessFunctionalized Ordered Mesoporous MCM-48 Silica: Synthesis, Characterization and Adsorbent for CO2 Capture
The ordered mesoporous silica MCM-48 with cubic Ia3d structure was synthesized using the cationic surfactant hexadecyltrimethylammonium bromide (CTAB) as a template agent and tetraethylorthosilicate (TEOS) as a silica source. The obtained material was first functionalized with (3-glycidyloxypropyl)trimethoxysilane (KH560); further, two types of amination reagents were used: ethylene diamine (N2) and diethylene triamine (N3). The modified amino-functionalized materials were characterized by powder X-ray diffraction (XRD) at low angles, infrared spectroscopy (FT-IR) and nitrogen adsorption–desorption experiments at 77 K. Characterization from a structural point of view reveals that the ordered MCM-48 mesoporous silica has a highly ordered structure and a large surface area (1466.059 m2/g) and pore volume (0.802 cm3/g). The amino-functionalized MCM-48 molecular sieves were tested for CO2 adsorption–desorption properties at different temperatures using thermal program desorption (TPD). Promising results for CO2 adsorption capacities were achieved for MCM-48 sil KH560-N3 at 30 °C. At 30 °C, the MCM-48 sil KH560-N3 sample has an adsorption capacity of 3.17 mmol CO2/g SiO2, and an efficiency of amino groups of 0.58 mmol CO2/mmolNH2. After nine adsorption–desorption cycles, the results suggest that the performance of the MCM-48 sil KH N2 and MCM-48 sil KH N3 adsorbents is relatively stable, presenting a low decrease in the adsorption capacity. The results reported in this paper for the investigated amino-functionalized molecular sieves as absorbents for CO2 can be considered as promising.
- Open Access
Ni and Ce Grafted Ordered Mesoporous Silica KIT-6 for CO2 Adsorption
In this study, the Ni/KIT-6 and Ce/KIT-6 materials were prepared through the impregnation method and then amino-functionalized materials were obtained by the grafting of an amino-silane coupling agent 3-aminopropyl triethoxysilane (APTES). The samples were characterized by thermogravimetric analysis (TGA-DTA), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction, scanning electron microscopy (SEM) and nitrogen adsorption at 77 K. The study of CO2 adsorption–desorption on prepared materials was investigated using thermogravimetric analysis (TGA-DTA) coupled with mass spectrometry (MS). The influence of metal oxides on the performance of CO2 adsorption on functionalized mesoporous silica was presented. The results showed that doping the molecular sieve with cerium oxide can significantly increase the adsorption capacity of the amino-functionalized KIT-6. As the CO2 adsorbents were prepared by functionalization through grafting with APTES, the amount of amine loading is one of the important factors which improves CO2 adsorption capacity. Additionally, CO2 adsorption performance depends on the textural properties and the temperature used for the adsorption process. The maximum adsorption capacity of Ce/KIT-6 Sil is 3.66 mmol/g, which is 2.4 times higher than Ni/KIT-6 Sil. After the nine cycles of cyclic CO2 adsorption/desorption, the Ce/KIT-6 Sil still had higher adsorption capacities, indicating their good cyclical stability.
Open AccessNi and Ce Grafted Ordered Mesoporous Silica KIT-6 for CO2 Adsorption
In this study, the Ni/KIT-6 and Ce/KIT-6 materials were prepared through the impregnation method and then amino-functionalized materials were obtained by the grafting of an amino-silane coupling agent 3-aminopropyl triethoxysilane (APTES). The samples were characterized by thermogravimetric analysis (TGA-DTA), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction, scanning electron microscopy (SEM) and nitrogen adsorption at 77 K. The study of CO2 adsorption–desorption on prepared materials was investigated using thermogravimetric analysis (TGA-DTA) coupled with mass spectrometry (MS). The influence of metal oxides on the performance of CO2 adsorption on functionalized mesoporous silica was presented. The results showed that doping the molecular sieve with cerium oxide can significantly increase the adsorption capacity of the amino-functionalized KIT-6. As the CO2 adsorbents were prepared by functionalization through grafting with APTES, the amount of amine loading is one of the important factors which improves CO2 adsorption capacity. Additionally, CO2 adsorption performance depends on the textural properties and the temperature used for the adsorption process. The maximum adsorption capacity of Ce/KIT-6 Sil is 3.66 mmol/g, which is 2.4 times higher than Ni/KIT-6 Sil. After the nine cycles of cyclic CO2 adsorption/desorption, the Ce/KIT-6 Sil still had higher adsorption capacities, indicating their good cyclical stability.
- Open Access
Thermogravimetry Applied for Investigation of Coke Formation in Ethanol Conversion over Heteropoly Tungstate Catalysts
Thermogravimetric analysis (TGA) was used to evaluate the thermal stability and the amount of coke deposition resulting from the deactivation of catalysts during ethanol dehydration reaction in a fixed bed continuous flow reactor. In this study, a series of catalysts containing 30% of Pd doped and pure 12-tungstophosphoric acid and its insoluble Cs2.5H0.5PW12O40 salt supported on SBA-15 were prepared. The catalytic efficiency of ethanol dehydration reaction was also evaluated. Two types of coke are identified from the TPO (Temperature programmed oxidation) profiles and assigned to the coke precursor and hard coke, respectively. The results indicate that cesium salts reduced the formation of hard coke. The amount of total coke formed was significantly reduced by supporting the catalysts on mesoporous SBA-15 molecular sieves.
Open AccessThermogravimetry Applied for Investigation of Coke Formation in Ethanol Conversion over Heteropoly Tungstate Catalysts
Thermogravimetric analysis (TGA) was used to evaluate the thermal stability and the amount of coke deposition resulting from the deactivation of catalysts during ethanol dehydration reaction in a fixed bed continuous flow reactor. In this study, a series of catalysts containing 30% of Pd doped and pure 12-tungstophosphoric acid and its insoluble Cs2.5H0.5PW12O40 salt supported on SBA-15 were prepared. The catalytic efficiency of ethanol dehydration reaction was also evaluated. Two types of coke are identified from the TPO (Temperature programmed oxidation) profiles and assigned to the coke precursor and hard coke, respectively. The results indicate that cesium salts reduced the formation of hard coke. The amount of total coke formed was significantly reduced by supporting the catalysts on mesoporous SBA-15 molecular sieves.
- 1 April 2021
- Published by Elsevier in Catalysis Today
- Vol. 366, 123-132
Catalytic activity of heteropoly tungstate catalysts for ethanol dehydration reaction: Deactivation and regeneration
- 1 April 2021
- Published by Elsevier in Catalysis Today
- Vol. 366, 123-132
Catalytic activity of heteropoly tungstate catalysts for ethanol dehydration reaction: Deactivation and regeneration
- 9 July 2019
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 128 (1) , 53-69
The influence of palladium on the catalytic activity for ethanol conversion over heteropoly tungstate catalysts
- 9 July 2019
- Published by Springer Nature in Reaction Kinetics, Mechanisms and Catalysis
- Vol. 128 (1) , 53-69
The influence of palladium on the catalytic activity for ethanol conversion over heteropoly tungstate catalysts
- 30 June 2015
- Published by Springer Nature in Journal of Materials Science
- Vol. 50 (19) , 6382-6387
Single-step combustion synthesis of YAlO3 powders
- 30 June 2015
- Published by Springer Nature in Journal of Materials Science
- Vol. 50 (19) , 6382-6387
Single-step combustion synthesis of YAlO3 powders
- 1 June 2014
- Published by Elsevier in Ceramics International
- Vol. 40 (5) , 7561-7565
Single-step combustion synthesis of LaAlO3 powders and their sintering behavior
- 1 June 2014
- Published by Elsevier in Ceramics International
- Vol. 40 (5) , 7561-7565
Single-step combustion synthesis of LaAlO3 powders and their sintering behavior
- 1 March 2014
- Published by Elsevier in Chemical Engineering Journal
- Vol. 240, 260-263
Large surface area ZnAl2O4 powders prepared by a modified combustion technique
- 1 March 2014
- Published by Elsevier in Chemical Engineering Journal
- Vol. 240, 260-263
Large surface area ZnAl2O4 powders prepared by a modified combustion technique
- 1 April 2013
- Published by Elsevier in Ceramics International
- Vol. 39 (3) , 2645-2650
Nanocrystalline BaAl2O4 powders prepared by aqueous combustion synthesis
- 1 April 2013
- Published by Elsevier in Ceramics International
- Vol. 39 (3) , 2645-2650
Nanocrystalline BaAl2O4 powders prepared by aqueous combustion synthesis