Wojciech Szkliniarz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wojciech Szkliniarz has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
Agnieszka Szkliniarz
9 shared publications- Agnieszka Szkliniarz
Faculty of Materials Engineering, Silesian University of Technology, 40-019 Katowice, Poland
6 shared publications A. Szkliniarz
3 shared publications- Jacek Chrapoński
Silesian University of Technology, Department of Materials Technologies, 8. Krasińskiego Str., 40-019 Katowice, Poland
3 shared publications A. Kościelna
2 shared publicationsB. Serek
2 shared publications
Latest Publications
- Open Access
The Role of Titanium Carbides in Forming the Microstructure and Properties of Ti-33Mo-0.2C Alloy
This study presents the characteristics of the Ti-33Mo-0.2C alloy, which belongs to the group of titanium alloys with a stable β phase and contains 0.27 wt% carbon; this is significantly higher than the permissible level for this alloy, which is 0.1 wt%. The Ti-33Mo-0.2C alloy was melted in a vacuum induction furnace with a cold copper crucible and subsequently processed into a 12 mm diameter rod through hot rolling and annealing under standard conditions. The microstructure, as well as the mechanical and physicochemical properties of the Ti-33Mo-0.2C alloy, were compared with those of the Ti-33Mo alloy of a similar chemical composition. The following techniques were used to characterize the microstructure and properties of the alloys: LM; SEM/EDS (WDS); XRD; and mechanical, creep, and corrosion testing. The conducted analyses demonstrated that the addition of approximately 0.2 wt% carbon to the Ti-33Mo alloy leads to the expected improvement in microstructural stability by reducing grain growth and inhibiting the precipitation of the α phase at β grain boundaries. Consequently, a unique simultaneous enhancement of both strength and ductility, with increased creep resistance, is observed while maintaining the excellent corrosion resistance of the investigated alloy. The observed beneficial effects and additional capabilities resulting from the presence of carbon in the investigated alloy justify the conclusion that carbon should no longer be regarded as an undesirable impurity, which stands in contrast to some previous statements.
Open AccessThe Role of Titanium Carbides in Forming the Microstructure and Properties of Ti-33Mo-0.2C Alloy
This study presents the characteristics of the Ti-33Mo-0.2C alloy, which belongs to the group of titanium alloys with a stable β phase and contains 0.27 wt% carbon; this is significantly higher than the permissible level for this alloy, which is 0.1 wt%. The Ti-33Mo-0.2C alloy was melted in a vacuum induction furnace with a cold copper crucible and subsequently processed into a 12 mm diameter rod through hot rolling and annealing under standard conditions. The microstructure, as well as the mechanical and physicochemical properties of the Ti-33Mo-0.2C alloy, were compared with those of the Ti-33Mo alloy of a similar chemical composition. The following techniques were used to characterize the microstructure and properties of the alloys: LM; SEM/EDS (WDS); XRD; and mechanical, creep, and corrosion testing. The conducted analyses demonstrated that the addition of approximately 0.2 wt% carbon to the Ti-33Mo alloy leads to the expected improvement in microstructural stability by reducing grain growth and inhibiting the precipitation of the α phase at β grain boundaries. Consequently, a unique simultaneous enhancement of both strength and ductility, with increased creep resistance, is observed while maintaining the excellent corrosion resistance of the investigated alloy. The observed beneficial effects and additional capabilities resulting from the presence of carbon in the investigated alloy justify the conclusion that carbon should no longer be regarded as an undesirable impurity, which stands in contrast to some previous statements.
- Open Access
Microstructure and Properties of Ti-5Al-2.5Sn Alloy with Higher Carbon Content
This study investigates the characteristics of the Ti-5Al-2.5Sn-0.2C alloy, an alpha titanium alloy containing approximately 0.2 wt% carbon—a concentration significantly exceeding the standard allowable limit of 0.08 wt%. The Ti-5Al-2.5Sn-0.2C alloy was melted in a vacuum induction furnace with a cold copper crucible, processed into bar form through hot rolling, and subsequently annealed under standard conditions. The microstructure and mechanical properties of the Ti-5Al-2.5Sn-0.2C alloy were systematically compared with those of the Ti-5Al-2.5Sn alloy (Grade 6), which possesses a similar chemical composition. The results revealed that the addition of 0.2 wt% carbon significantly influences the alloy’s solidification process, phase transformation temperatures, phase composition, and phase lattice parameters. Moreover, the carbon addition enhances key mechanical properties, including tensile strength, yield strength, hardness, and wear resistance, as well as creep and oxidation resistance. While a slight reduction in plasticity and increase in impact energy were observed, the alloy remained within the permissible range defined by existing standards.
Open AccessMicrostructure and Properties of Ti-5Al-2.5Sn Alloy with Higher Carbon Content
This study investigates the characteristics of the Ti-5Al-2.5Sn-0.2C alloy, an alpha titanium alloy containing approximately 0.2 wt% carbon—a concentration significantly exceeding the standard allowable limit of 0.08 wt%. The Ti-5Al-2.5Sn-0.2C alloy was melted in a vacuum induction furnace with a cold copper crucible, processed into bar form through hot rolling, and subsequently annealed under standard conditions. The microstructure and mechanical properties of the Ti-5Al-2.5Sn-0.2C alloy were systematically compared with those of the Ti-5Al-2.5Sn alloy (Grade 6), which possesses a similar chemical composition. The results revealed that the addition of 0.2 wt% carbon significantly influences the alloy’s solidification process, phase transformation temperatures, phase composition, and phase lattice parameters. Moreover, the carbon addition enhances key mechanical properties, including tensile strength, yield strength, hardness, and wear resistance, as well as creep and oxidation resistance. While a slight reduction in plasticity and increase in impact energy were observed, the alloy remained within the permissible range defined by existing standards.
- Open Access
Carbon in Commercially Pure Titanium
In a way so far unmatched in any single study, this paper presents the complex characteristics of commercially pure titanium (CP-Ti) containing 0.2 wt.% carbon, which is significantly above the carbon level in commonly used titanium alloys, while at the same time being the maximum permitted content in light of the recommendations in force. It has been demonstrated that the addition of carbon in CP-Ti can have many positive impacts. The investigated Ti-0.2C alloy was produced in a cold-copper crucible induction vacuum furnace and processed into a 12 mm diameter bar by hot rolling. The structure and properties of the Ti-0.2C alloy were compared to those of an CP-Ti Grade 1 produced and processed under the same technical conditions. The addition of 0.2 wt.% carbon to CP-Ti has been found to change the course of the crystallization process, the course and temperatures of phase transformations, and the values of lattice parameters; reduce susceptibility to grain growth; and create the possibility for additional hardening during solution treatment and aging. At the same time, it results in an assumed improvement in properties by increasing the tensile strength and yield strength, hardness, creep and oxidation resistance, and abrasive wear. It has a negative effect but is still within the acceptable range on impact strength and susceptibility to hot and cold deformation.
Open AccessCarbon in Commercially Pure Titanium
In a way so far unmatched in any single study, this paper presents the complex characteristics of commercially pure titanium (CP-Ti) containing 0.2 wt.% carbon, which is significantly above the carbon level in commonly used titanium alloys, while at the same time being the maximum permitted content in light of the recommendations in force. It has been demonstrated that the addition of carbon in CP-Ti can have many positive impacts. The investigated Ti-0.2C alloy was produced in a cold-copper crucible induction vacuum furnace and processed into a 12 mm diameter bar by hot rolling. The structure and properties of the Ti-0.2C alloy were compared to those of an CP-Ti Grade 1 produced and processed under the same technical conditions. The addition of 0.2 wt.% carbon to CP-Ti has been found to change the course of the crystallization process, the course and temperatures of phase transformations, and the values of lattice parameters; reduce susceptibility to grain growth; and create the possibility for additional hardening during solution treatment and aging. At the same time, it results in an assumed improvement in properties by increasing the tensile strength and yield strength, hardness, creep and oxidation resistance, and abrasive wear. It has a negative effect but is still within the acceptable range on impact strength and susceptibility to hot and cold deformation.
- Open Access
Microstructure and Properties of TiAl-Based Alloys Melted in Graphite Crucible
This paper presents the chemical and phase composition, microstructure, and selected properties both at room temperature and at the temperature corresponding to the expected operating conditions of three successive generations of TiAl-based alloys (Ti-47Al-2W-0.5Si, Ti-45Al-8Nb-0.5(B,C), and Ti-45Al-5Nb-2Cr-1Mo-0.5(B,C)-0.2Si) melted in a vacuum induction furnace with high-density isostatic pressed graphite crucibles. The obtained results of mechanical and physical properties of the produced alloys were compared to the properties of reference alloys with similar chemical composition and melted in a cold copper crucible furnace. The effect of increased carbon content in the produced alloys due to the degradation of the graphite crucible during melting is higher strength properties, lower plastic properties, higher coefficient of thermal expansion, and improved creep resistance. It was shown that the proposed technology could be successfully used in the production of different generation TiAl-based intermetallic alloys.
Open AccessMicrostructure and Properties of TiAl-Based Alloys Melted in Graphite Crucible
This paper presents the chemical and phase composition, microstructure, and selected properties both at room temperature and at the temperature corresponding to the expected operating conditions of three successive generations of TiAl-based alloys (Ti-47Al-2W-0.5Si, Ti-45Al-8Nb-0.5(B,C), and Ti-45Al-5Nb-2Cr-1Mo-0.5(B,C)-0.2Si) melted in a vacuum induction furnace with high-density isostatic pressed graphite crucibles. The obtained results of mechanical and physical properties of the produced alloys were compared to the properties of reference alloys with similar chemical composition and melted in a cold copper crucible furnace. The effect of increased carbon content in the produced alloys due to the degradation of the graphite crucible during melting is higher strength properties, lower plastic properties, higher coefficient of thermal expansion, and improved creep resistance. It was shown that the proposed technology could be successfully used in the production of different generation TiAl-based intermetallic alloys.
- Open Access
The Influence of Aluminizing Process on the Surface Condition and Oxidation Resistance of Ti–45Al–8Nb–0.5(B, C) Alloy
One of the major barriers limiting the suitability of TiAl intermetallic alloys for use in the demanding aircraft and automotive industries is their susceptibility to degradation as a result of oxidation at temperatures exceeding 760 °C. Paper presents the characteristics of resistance to cyclic oxidation at 950 °C for Ti–45Al–8Nb–0.5(B, C) alloy with and without protective coating obtained as a result of aluminizing using out of pack method. The characteristics of surface condition were determined by scanning electron microscope with EDS system, transmission electron microscope, and X-ray diffractometer. The favorable behavior of the Ti–45Al–8Nb–0.5(B, C) alloy with a protective coating under cyclic oxidation conditions is a result of a higher content of Al2O3 in the microstructure of the scale and the presence of Al and Nb-rich phases at the substrate interface, which probably constitue a barrier for oxidation process. The high temperature oxidation test revealed that aluminide coating was responsible for a remarkable improvement in the oxidation resistance.
Open AccessThe Influence of Aluminizing Process on the Surface Condition and Oxidation Resistance of Ti–45Al–8Nb–0.5(B, C) Alloy
One of the major barriers limiting the suitability of TiAl intermetallic alloys for use in the demanding aircraft and automotive industries is their susceptibility to degradation as a result of oxidation at temperatures exceeding 760 °C. Paper presents the characteristics of resistance to cyclic oxidation at 950 °C for Ti–45Al–8Nb–0.5(B, C) alloy with and without protective coating obtained as a result of aluminizing using out of pack method. The characteristics of surface condition were determined by scanning electron microscope with EDS system, transmission electron microscope, and X-ray diffractometer. The favorable behavior of the Ti–45Al–8Nb–0.5(B, C) alloy with a protective coating under cyclic oxidation conditions is a result of a higher content of Al2O3 in the microstructure of the scale and the presence of Al and Nb-rich phases at the substrate interface, which probably constitue a barrier for oxidation process. The high temperature oxidation test revealed that aluminide coating was responsible for a remarkable improvement in the oxidation resistance.
- 13 December 2017
- Published by SAGE Publications in Materials Science and Technology
- Vol. 35 (3) , 297-305
The characteristics of TiAl-based alloys melted in graphite crucibles
In the paper, the phase composition, microstructure, and selected mechanical and operational properties at room and elevated temperature of a TiAl intermetallic alloy from the TNB group – Ti–45Al–8Nb–0.5(B, C), induction melted in special graphite crucibles, are characterised. Selected properties of this alloy were compared to those of the reference TNB-V2 alloy with similar chemical composition, prepared with technologies currently used in the world. The result of this comparison was a positive recommendation for the proposed melting technology as an alternative to this and other groups of TiAl-based alloys. This paper is part of a thematic issue on Titanium.
- 13 December 2017
- Published by SAGE Publications in Materials Science and Technology
- Vol. 35 (3) , 297-305
The characteristics of TiAl-based alloys melted in graphite crucibles
In the paper, the phase composition, microstructure, and selected mechanical and operational properties at room and elevated temperature of a TiAl intermetallic alloy from the TNB group – Ti–45Al–8Nb–0.5(B, C), induction melted in special graphite crucibles, are characterised. Selected properties of this alloy were compared to those of the reference TNB-V2 alloy with similar chemical composition, prepared with technologies currently used in the world. The result of this comparison was a positive recommendation for the proposed melting technology as an alternative to this and other groups of TiAl-based alloys. This paper is part of a thematic issue on Titanium.
- Open Access
- 1 September 2016
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 61 (3) , 1385-1390
Fundamentals of Manufacturing Technologies for Aircraft Engine Parts Made of TiAl Based Alloys
The study presents fundamentals of manufacturing technologies for aircraft engine construction elements, made of light, intermetallic TiAl based alloy, which is characterized by high relative strength and good creep and oxidation resistance. For smelting of alloy, the vacuum metallurgy methods were used, including application of induction furnace equipped with special crucibles made of isostatic-pressed, high-density graphite. To produce good quality construction element for aircraft engine, such as low-pressure turbine blade, there were methods of gravity casting from a very high temperature to the preheated shell moulds applied
- 1 September 2016
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 61 (3) , 1385-1390
Open AccessFundamentals of Manufacturing Technologies for Aircraft Engine Parts Made of TiAl Based Alloys
The study presents fundamentals of manufacturing technologies for aircraft engine construction elements, made of light, intermetallic TiAl based alloy, which is characterized by high relative strength and good creep and oxidation resistance. For smelting of alloy, the vacuum metallurgy methods were used, including application of induction furnace equipped with special crucibles made of isostatic-pressed, high-density graphite. To produce good quality construction element for aircraft engine, such as low-pressure turbine blade, there were methods of gravity casting from a very high temperature to the preheated shell moulds applied
- Open Access
- 1 March 2016
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 61 (1) , 347-352
Microstructure of Hot-Deformed Cu-3Ti Alloy
In the paper, results of investigations regarding temperature and strain rate effects on hot-deformed Cu-3Ti alloy microstructure are presented. Evaluation of the alloy microstructure was performed with the use of a Gleeble HDS-V40 thermal-mechanical simulator on samples subjected to uniaxial hot compression within 700 to 900ºC and at the strain rate of 0.1, 1.0 or 10.0 s-1until 70% (1.2) strain. It was found that within the analyzed temperature and strain rate ranges, the alloy deformation led to partial or complete recrystallization of its structure and to multiple refinement of the initial grains. The recrystallization level and the average diameter of recrystallized grains increase with growing temperature and strain rate. It was shown that entirely recrystallized, fine-grained alloy structure could be obtained following deformation at the strain rate of min 10.0 s-1and the temperature of 800°C or higher.
- 1 March 2016
- Published by Walter de Gruyter GmbH in Archives of Metallurgy and Materials
- Vol. 61 (1) , 347-352
Open AccessMicrostructure of Hot-Deformed Cu-3Ti Alloy
In the paper, results of investigations regarding temperature and strain rate effects on hot-deformed Cu-3Ti alloy microstructure are presented. Evaluation of the alloy microstructure was performed with the use of a Gleeble HDS-V40 thermal-mechanical simulator on samples subjected to uniaxial hot compression within 700 to 900ºC and at the strain rate of 0.1, 1.0 or 10.0 s-1until 70% (1.2) strain. It was found that within the analyzed temperature and strain rate ranges, the alloy deformation led to partial or complete recrystallization of its structure and to multiple refinement of the initial grains. The recrystallization level and the average diameter of recrystallized grains increase with growing temperature and strain rate. It was shown that entirely recrystallized, fine-grained alloy structure could be obtained following deformation at the strain rate of min 10.0 s-1and the temperature of 800°C or higher.
- 1 February 2016
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 246, 11-14
Effect of Neodymium Addition on the Microstructure of Ti-47Al-2W-0.5Si Alloy
In the study there was conducted characteristics of macro-and microstructure of casted Ti-47Al-2W-0.5Si alloy, based on intermetallic TiAl phase. There were presented possibilities for change of unfavorable parameters of this structure – large grain and high content of columnar grains – through the use of modifier in the form of a crystalline neodymium. There was shown the effect of modification process on selected properties of the alloy. There were determined: the content of modifier, by which changes in structure are largest, and the form, in which the modifier is present in the modified alloy.
- 1 February 2016
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 246, 11-14
Effect of Neodymium Addition on the Microstructure of Ti-47Al-2W-0.5Si Alloy
In the study there was conducted characteristics of macro-and microstructure of casted Ti-47Al-2W-0.5Si alloy, based on intermetallic TiAl phase. There were presented possibilities for change of unfavorable parameters of this structure – large grain and high content of columnar grains – through the use of modifier in the form of a crystalline neodymium. There was shown the effect of modification process on selected properties of the alloy. There were determined: the content of modifier, by which changes in structure are largest, and the form, in which the modifier is present in the modified alloy.
- 1 September 2015
- Published by Elsevier in Surface and Coatings Technology
- Vol. 277, 270-277
Improvement of oxidation resistance of Ti–47Al–2W–0.5Si alloy modified by aluminizing method
- 1 September 2015
- Published by Elsevier in Surface and Coatings Technology
- Vol. 277, 270-277
Improvement of oxidation resistance of Ti–47Al–2W–0.5Si alloy modified by aluminizing method