Mohammad Reza Mansoori
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohammad Reza Mansoori has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
- Abdolreza Sarvghad Moghadam
Structural Engineering Research Center, International Institute of Earthquake Engineering and Seismology, Tehran, Iran
4 shared publications - Armin Aziminejad
Department of Civil Engineering, SR.C., Islamic Azad University, Tehran, Iran
4 shared publications Armin Aziminejad
Department of Civil Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
3 shared publicationsAbdolreza S. Moghadam
International Institute of Earthquake Engineering and Seismology, Tehran, Iran
2 shared publicationsMirhamid Hosseini
Department of Civil Engineering, Science and Research Branch, Islamic Azad University, Tehran, Iran
2 shared publications- Mohamad Reza Shokrzadeh
University of Qom
2 shared publications
Latest Publications
- Open Access
- 25 September 2026
- Published by Elsevier in SSRN Electronic Journal
Evaluation of the Bidirectional Energy-Based Pushover Method for Assessing Directional Effects on the Seismic Response of Curved Bridges
Accurate evaluation of the seismic response of curved bridges under different earthquake incidence angles is challenging because of the interaction between bridge curvature, structural configuration, and the two orthogonal components of ground motion. This study evaluates the capability of the Bidirectional Energy-Based Pushover (BEP) method to reproduce the seismic response of reinforced concrete (RC) curved bridges under different directions of earthquake excitation, using Incremental Dynamic Analysis (IDA) as the reference approach. Fifteen bridge classes comprising two-, three-, and four-span configurations with radii of curvature of 130, 240, 420, 700, and 1000 m were investigated. Twenty-two pairs of ground-motion records were applied at incidence angles of 0°, 45°, and 90°, and the nonlinear seismic responses obtained from BEP and IDA were systematically compared. The results indicate that the seismic response of the investigated curved bridges is sensitive to the direction of excitation, with the 45° incidence angle producing the largest discrepancy between the BEP and IDA results among the examined directions for the investigated bridge configurations. The comparison between BEP and IDA further shows that the accuracy of the BEP method is direction- and configuration-dependent. In particular, the discrepancy between BEP and IDA becomes more pronounced under the critical 45° excitation direction, indicating limitations in the ability of the energy-based approach to reproduce direction-dependent seismic responses. These findings highlight the importance of considering excitation direction when evaluating simplified nonlinear analysis procedures for curved bridges and provide a basis for identifying the conditions under which BEP can be reliably applied.
- 25 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEvaluation of the Bidirectional Energy-Based Pushover Method for Assessing Directional Effects on the Seismic Response of Curved Bridges
Accurate evaluation of the seismic response of curved bridges under different earthquake incidence angles is challenging because of the interaction between bridge curvature, structural configuration, and the two orthogonal components of ground motion. This study evaluates the capability of the Bidirectional Energy-Based Pushover (BEP) method to reproduce the seismic response of reinforced concrete (RC) curved bridges under different directions of earthquake excitation, using Incremental Dynamic Analysis (IDA) as the reference approach. Fifteen bridge classes comprising two-, three-, and four-span configurations with radii of curvature of 130, 240, 420, 700, and 1000 m were investigated. Twenty-two pairs of ground-motion records were applied at incidence angles of 0°, 45°, and 90°, and the nonlinear seismic responses obtained from BEP and IDA were systematically compared. The results indicate that the seismic response of the investigated curved bridges is sensitive to the direction of excitation, with the 45° incidence angle producing the largest discrepancy between the BEP and IDA results among the examined directions for the investigated bridge configurations. The comparison between BEP and IDA further shows that the accuracy of the BEP method is direction- and configuration-dependent. In particular, the discrepancy between BEP and IDA becomes more pronounced under the critical 45° excitation direction, indicating limitations in the ability of the energy-based approach to reproduce direction-dependent seismic responses. These findings highlight the importance of considering excitation direction when evaluating simplified nonlinear analysis procedures for curved bridges and provide a basis for identifying the conditions under which BEP can be reliably applied.
- 5 September 2026
- Published by Elsevier in Structures
- Vol. 93
Experimental evaluation of reduced-depth inverse-haunch RC beam–column joints under cyclic loading
- 5 September 2026
- Published by Elsevier in Structures
- Vol. 93
Experimental evaluation of reduced-depth inverse-haunch RC beam–column joints under cyclic loading
- 28 August 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- p. 1-13
Necessity of steel staircase separation and development of simplified design relationships
This study seeks to demonstrate the necessity of separating the staircase from the primary structure and, as an innovative and practical objective, to find a simplified and meaningful relationship between the inter-storey drift obtained from simplified analyses and measures such as the separation gap width in the separation method. Interaction between staircase components and the primary structure may lead to unforeseen behaviour in both the staircase components and the primary structure. Therefore, the separation method has a strong scientific and functional rationale. To this end, 48 steel building models were investigated. The results indicate that the ratio of the gap size to the inter-storey drift obtained from linear equivalent static analysis is similar among the studied models, except for the two-storey model. This ratio is at most 1.5 times at the first intermediate floor and at most 60% in the remaining floors. In the two-storey model, this ratio reaches up to three times at the first intermediate floor, while in the remaining floors it remains the same 60%. Furthermore, the provisions of the American Society of Civil Engineers/Structural Engineering Institute 7-22 standard concerning the minimum separation gap are considered inadequate for mid-rise steel moment-resisting frame structures.
- 28 August 2026
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Structures and Buildings
- p. 1-13
Necessity of steel staircase separation and development of simplified design relationships
This study seeks to demonstrate the necessity of separating the staircase from the primary structure and, as an innovative and practical objective, to find a simplified and meaningful relationship between the inter-storey drift obtained from simplified analyses and measures such as the separation gap width in the separation method. Interaction between staircase components and the primary structure may lead to unforeseen behaviour in both the staircase components and the primary structure. Therefore, the separation method has a strong scientific and functional rationale. To this end, 48 steel building models were investigated. The results indicate that the ratio of the gap size to the inter-storey drift obtained from linear equivalent static analysis is similar among the studied models, except for the two-storey model. This ratio is at most 1.5 times at the first intermediate floor and at most 60% in the remaining floors. In the two-storey model, this ratio reaches up to three times at the first intermediate floor, while in the remaining floors it remains the same 60%. Furthermore, the provisions of the American Society of Civil Engineers/Structural Engineering Institute 7-22 standard concerning the minimum separation gap are considered inadequate for mid-rise steel moment-resisting frame structures.
- 19 April 2025
- Published by Wiley in Structural Concrete
- Vol. 26 (6) , 7204-7224
Cold rolling versus rotating friction welding techniques in mechanical splices: Study of the inelastic cyclic behavior of reinforced concrete columns
Selecting an optimal bar splicing technique is a pivotal challenge in reinforced concrete (RC) columns, particularly in seismic zones, due to its profound influence on structural performance, construction efficiency, and economic viability. This study presents a comprehensive experimental and analytical investigation into the inelastic cyclic behavior of RC columns incorporating threaded splices fabricated through two advanced techniques: cold rolling and rotary friction welding. The research aims to elucidate the effects of these splicing methods on critical seismic performance parameters, including displacement and curvature ductility, plastic hinge length, and energy dissipation. Experimental tests conducted on 1/3‐scale RC columns revealed that rotary friction welding splices with threaded couplers (RFWTC) significantly enhanced displacement ductility, curvature ductility, and energy dissipation capacities compared to oversize‐threaded couplers (OTC) and non‐spliced specimens. The superior performance of RFWTC splices was attributed to delayed bar buckling, improved bond strength, and extended plastic hinge zones. Additionally, an idealized backbone model for nonlinear analysis was developed and validated, demonstrating strong agreement with experimental observations. A refined equation for calculating plastic hinge length is also proposed, incorporating the influence of mechanical splices and confinement effects. The findings underscore the reliability and effectiveness of OTC and RFWTC splicing techniques for use in plastic hinge regions of RC columns subjected to seismic loading. These methods not only enhance ductility and energy dissipation but also address challenges associated with bar buckling and stress concentration, making them suitable for high‐performance structural applications in seismic regions.
- 19 April 2025
- Published by Wiley in Structural Concrete
- Vol. 26 (6) , 7204-7224
Cold rolling versus rotating friction welding techniques in mechanical splices: Study of the inelastic cyclic behavior of reinforced concrete columns
Selecting an optimal bar splicing technique is a pivotal challenge in reinforced concrete (RC) columns, particularly in seismic zones, due to its profound influence on structural performance, construction efficiency, and economic viability. This study presents a comprehensive experimental and analytical investigation into the inelastic cyclic behavior of RC columns incorporating threaded splices fabricated through two advanced techniques: cold rolling and rotary friction welding. The research aims to elucidate the effects of these splicing methods on critical seismic performance parameters, including displacement and curvature ductility, plastic hinge length, and energy dissipation. Experimental tests conducted on 1/3‐scale RC columns revealed that rotary friction welding splices with threaded couplers (RFWTC) significantly enhanced displacement ductility, curvature ductility, and energy dissipation capacities compared to oversize‐threaded couplers (OTC) and non‐spliced specimens. The superior performance of RFWTC splices was attributed to delayed bar buckling, improved bond strength, and extended plastic hinge zones. Additionally, an idealized backbone model for nonlinear analysis was developed and validated, demonstrating strong agreement with experimental observations. A refined equation for calculating plastic hinge length is also proposed, incorporating the influence of mechanical splices and confinement effects. The findings underscore the reliability and effectiveness of OTC and RFWTC splicing techniques for use in plastic hinge regions of RC columns subjected to seismic loading. These methods not only enhance ductility and energy dissipation but also address challenges associated with bar buckling and stress concentration, making them suitable for high‐performance structural applications in seismic regions.
- 16 April 2025
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 50 (1) , 733-748
Seismic Design of Mid-Rise Steel Diagrid Structures Considering Life Cycle Cost
- 16 April 2025
- Published by Springer Nature in Iranian Journal of Science and Technology, Transactions of Civil Engineering
- Vol. 50 (1) , 733-748
Seismic Design of Mid-Rise Steel Diagrid Structures Considering Life Cycle Cost
- 24 March 2025
- Published by Elsevier in Structures
- Vol. 75
Seismic and harmonic response analysis of vertically mass isolated multi-story steel structures equipped with tuned mass dampers
- 24 March 2025
- Published by Elsevier in Structures
- Vol. 75
Seismic and harmonic response analysis of vertically mass isolated multi-story steel structures equipped with tuned mass dampers
- 8 June 2024
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 25 (09)
Seismic Assessment of Self-Centering Rocking Braced Systems with Story Energy Dissipation
Self-centering rocking braced (SCRB) system provides enhanced seismic performance and reduced post-earthquake residual drift. However, the effect of higher modes is controversial, affecting shear demands and bending moments in the structure. This functional deficiency is addressed by developing SCRB frames equipped with buckling-restrained columns (BRCs) and buckling-restrained braces (BRBs), performing as exchangeable fuse frames. The system consists of external columns branching off from the main core and connected to it via butterfly-shaped fuses, and BRC and BRB are incorporated into the core at four different height levels to be compared with conventional SCRB as the baseline. Three sets of 12-, 16- and 20-story structures are numerically developed in OpenSees finite element framework with regard to geometrical and material nonlinearities, making a total of 12 SCRB prototypes. The suit of 22 ground motions used in FEMA P695 was scaled to DBE and MCE hazard levels and applied to the structures. Results indicate the capability of the new system in reducing the destructive effects of higher modes, especially in the case of a fuse frame located in the middle of the height. In addition, the core moment and shear force largely reduced, almost 60%, in higher positions of the fuse frame, while those configurations led to large residual drift at the restrained level. However, all structures met the DBE-level 2% drift target. Moreover, increasing structural height nearly reduced seismic demands and increased response reductions. Overall, the system demonstrated acceptable performance in terms of high capacity for energy absorption.
- 8 June 2024
- Published by World Scientific Pub Co Pte Ltd in International Journal of Structural Stability and Dynamics
- Vol. 25 (09)
Seismic Assessment of Self-Centering Rocking Braced Systems with Story Energy Dissipation
Self-centering rocking braced (SCRB) system provides enhanced seismic performance and reduced post-earthquake residual drift. However, the effect of higher modes is controversial, affecting shear demands and bending moments in the structure. This functional deficiency is addressed by developing SCRB frames equipped with buckling-restrained columns (BRCs) and buckling-restrained braces (BRBs), performing as exchangeable fuse frames. The system consists of external columns branching off from the main core and connected to it via butterfly-shaped fuses, and BRC and BRB are incorporated into the core at four different height levels to be compared with conventional SCRB as the baseline. Three sets of 12-, 16- and 20-story structures are numerically developed in OpenSees finite element framework with regard to geometrical and material nonlinearities, making a total of 12 SCRB prototypes. The suit of 22 ground motions used in FEMA P695 was scaled to DBE and MCE hazard levels and applied to the structures. Results indicate the capability of the new system in reducing the destructive effects of higher modes, especially in the case of a fuse frame located in the middle of the height. In addition, the core moment and shear force largely reduced, almost 60%, in higher positions of the fuse frame, while those configurations led to large residual drift at the restrained level. However, all structures met the DBE-level 2% drift target. Moreover, increasing structural height nearly reduced seismic demands and increased response reductions. Overall, the system demonstrated acceptable performance in terms of high capacity for energy absorption.
- 23 March 2024
- Published by Elsevier in Structures
- Vol. 62
Time-dependent risk-targeted seismic design of RC moment-resisting frames under corrosive environment
- 23 March 2024
- Published by Elsevier in Structures
- Vol. 62
Time-dependent risk-targeted seismic design of RC moment-resisting frames under corrosive environment