MMMohamed R. Maafa

Mohamed R. Maafa

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mohamed R. Maafa has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Drew N. Maywar

    Department of Electrical and Microelectronic Engineering, Rochester Institute of Technology, Rochester, NY 14623, USA

    3 shared publications
  • M. Ravichandran

    Department of Electrical, Computer, and Telecommunications Engineering Technology Rochester Institute of Technology Rochester New York 14623 USA

    1 shared publication
  • S.K. Pham

    Department of Electrical, Computer, and Telecommunications Engineering Technology Rochester Institute of Technology Rochester New York 14623 USA

    1 shared publication
  • Saif A. Al Graiti

    IT research and development center, University of Kufa, Najaf, Iraq

    1 shared publication
  • Son Kim Pham

    Department of Electrical & Computer Engineering Technology, Rochester Institute of Technology, Rochester, NY 14623, United States of America

    1 shared publication

Latest Publications

  • Photonic fan-out and local selectable inversion of the optical hysteresis shape

    by Saif A. Al Graiti, Mohamed R. Maafa, Son Kim Pham, Drew N. Maywar

    We demonstrate and elucidate the local selectable inversion of the hysteresis shape of a bistable optical signal after fan-out. This selectability is based on a hysteresis-shape transformation that yields a switching contrast over 20 dB in magnitude for both the inversion clockwise (CW) and the non-inversion counterclockwise (CCW) hysteresis shapes, while maintaining input-switching powers. This behavior leverages an initial signal whose bistability is manifested by its state of polarization; a generalized Malus’ law elucidates how selection is possible by controlling the transmittivity hysteresis through each local polarizer. The concept is demonstrated using a Fabry–Pérot semiconductor optical amplifier to produce the initial bistable polarization-rotating signal, followed by a 1 × 2 fan-out and the realization of all four hysteresis shapes at each location, independent of the other location. This fan-out and selectable inversion behavior is applicable to other nonlinear photonic systems and provides new functionality for parallel optical processing.

  • Open Access

    Selectable microwave‐frequency doubling and quadrupling via optical path‐length tuning

    by M.R. Maafa, D.N. Maywar

    A technique to selectively double or quadruple the frequency of a microwave signal is experimentally demonstrated based on a commercial single‐output Mach–Zehnder modulator (MZM). Selectability is achieved by only a change in optical path length in a post‐MZM optical subsystem, without filtering and without changing the MZM drive voltage. This path length controls the synchronisation of two similarly shaped optical signals that are incoherently combined. Multiplication from 2 GHz (S‐band) to 4 GHz (C‐band, doubling) and to 8 GHz (X‐band, quadrupling) is demonstrated with side‐tone suppression greater than 24 dB. At a 10‐kHz offset from the quadrupled frequency, the phase‐noise degradation is only 7.9 dB, a 4.1‐dB improvement over traditional quadrupling techniques.

  • Open Access

    Microwave frequency doubling by synchronising and polarisation multiplexing the optical signals from a dual‐output Mach–Zehnder modulator

    by M.R. Maafa, S.K. Pham, M. Ravichandran, D.N. Maywar

    A technique is experimentally demonstrated to double the frequency of a microwave signal by synchronising and polarisation multiplexing the optical signals from a dual‐output Mach–Zehnder modulator. The frequency‐doubled tone at 4 GHz is 41.2 dB stronger than the residual fundamental‐frequency tone. The strongest side tone is found at 12 GHz (sixth order) and is suppressed by 32.7 dB. The phase noise of the frequency‐doubled signal is −104.1 dBc/Hz at an offset of 10 kHz, an increase of 6.7 dB over that of the initial signal. This technique does not rely on electronic or optical filters or amplifiers and is demonstrated using commercial off‐the‐shelf components.