Roger Stark
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Roger Stark has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Ulrike Grossner
ETH Zurich
12 shared publications - Ivana Kovacevic-Badstuebner
Advanced Power Semiconductor Laboratory, ETH Zurich, Zurich, Switzerland
5 shared publications - Alexander Tsibizov
Advanced Power Semiconductor Laboratory, ETH Zrich, Zrich, Switzerland
4 shared publications - Judith Woerle
ETH Zurich
3 shared publications - Arto Javanainen
Department of Physics, University of Jyvskyl, Jyvskyl, Finland
2 shared publications - Corinna Martinella
Advanced Power Semiconductor Laboratory (APS), ETH Zrich, Zrich, Switzerland
2 shared publications
Latest Publications
- Open Access
- 7 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7709-7715
Frequency-Dependent Internal Gate Resistance of SiC Power MOSFETs
This article presents an analysis of the internal gate resistance of silicon carbide (SiC) power MOSFETs and its influence on the dynamic device performance. The internal gate resistance of SiC power MOSFETs features a frequency and voltage dependency that is not observed for silicon (Si) power MOSFETs, and hence, not investigated in mature Si device technology. Using numerical device modeling based on experimental electrical characterization, the low-frequency (LF) behavior of the internal gate resistance is attributed to the defects at the SiC–oxide interface. The high-frequency (HF) behavior is explained by the gate signal propagation across the die area and incorporated in a proposed MOSFET model. In the example of a reference SiC power MOSFET design, the developed model is used to evaluate the differences between the simulated and the measured switching waveforms in more detail. The results do not only reveal the physics of the internal gate resistance of SiC power MOSFETs but also highlight how the standard SPICE models, which include the internal gate resistance as a lumped resistor, can be limited in modeling the switching waveforms of SiC power MOSFETs and estimating switching losses with high accuracy.
- 7 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (12) , 7709-7715
Open AccessFrequency-Dependent Internal Gate Resistance of SiC Power MOSFETs
This article presents an analysis of the internal gate resistance of silicon carbide (SiC) power MOSFETs and its influence on the dynamic device performance. The internal gate resistance of SiC power MOSFETs features a frequency and voltage dependency that is not observed for silicon (Si) power MOSFETs, and hence, not investigated in mature Si device technology. Using numerical device modeling based on experimental electrical characterization, the low-frequency (LF) behavior of the internal gate resistance is attributed to the defects at the SiC–oxide interface. The high-frequency (HF) behavior is explained by the gate signal propagation across the die area and incorporated in a proposed MOSFET model. In the example of a reference SiC power MOSFET design, the developed model is used to evaluate the differences between the simulated and the measured switching waveforms in more detail. The results do not only reveal the physics of the internal gate resistance of SiC power MOSFETs but also highlight how the standard SPICE models, which include the internal gate resistance as a lumped resistor, can be limited in modeling the switching waveforms of SiC power MOSFETs and estimating switching losses with high accuracy.
- Open Access
- 6 June 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1092, 165-170
Temperature Dependence of the Channel and Drift Resistance of SiC Power MOSFETs Extracted from I-V and C-V Measurements
SiC power MOSFETs show very promising electrical performance for efficient and reliable high temperature operation. This work presents a novel approach for the determination of the temperature dependence of SiC power MOSFET’s channel and drift resistance components in the on-state, which are extracted based on current-voltage (I-V) and capacitance-voltage (C-V) measurements without the need of data extrapolation. The results show that the channel resistance has weak, whereas the drift resistance has strong temperature dependence.
- 6 June 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1092, 165-170
Open AccessTemperature Dependence of the Channel and Drift Resistance of SiC Power MOSFETs Extracted from I-V and C-V Measurements
SiC power MOSFETs show very promising electrical performance for efficient and reliable high temperature operation. This work presents a novel approach for the determination of the temperature dependence of SiC power MOSFET’s channel and drift resistance components in the on-state, which are extracted based on current-voltage (I-V) and capacitance-voltage (C-V) measurements without the need of data extrapolation. The results show that the channel resistance has weak, whereas the drift resistance has strong temperature dependence.
- Open Access
- 5 June 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1091, 67-71
Small-Signal Impedance and Split C-V Characterization of High-κ SiC Power MOSFETs
In this work, the improvement of SiC power MOSFET performance achieved using high-κ gate-dielectrics instead of the standard SiO2 is investigated by means of advanced gate-impedance characterization. The benefit of using high-κ gate-dielectrics with high dielectric constant is demonstrated by comparing SiC MOSFETs with pure high-κ, a stack of SiO2/high-κ, as well as pure SiO2. Namely, the fabricated high-κ SiC MOSFETs show a superior performance to commercial SiC MOSFETs with SiO2/SiC interface with respect to channel resistance and interface quality. The proposed characterization approach is non-destructive and applicable to packaged power devices.
- 5 June 2023
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1091, 67-71
Open AccessSmall-Signal Impedance and Split C-V Characterization of High-κ SiC Power MOSFETs
In this work, the improvement of SiC power MOSFET performance achieved using high-κ gate-dielectrics instead of the standard SiO2 is investigated by means of advanced gate-impedance characterization. The benefit of using high-κ gate-dielectrics with high dielectric constant is demonstrated by comparing SiC MOSFETs with pure high-κ, a stack of SiO2/high-κ, as well as pure SiO2. Namely, the fabricated high-κ SiC MOSFETs show a superior performance to commercial SiC MOSFETs with SiO2/SiC interface with respect to channel resistance and interface quality. The proposed characterization approach is non-destructive and applicable to packaged power devices.
- Open Access
- 14 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (8) , 1844-1851
High-Energy Proton and Atmospheric-Neutron Irradiations of SiC Power MOSFETs: SEB Study and Impact on Channel and Drift Resistances
Accelerated single event burnout (SEB) tests with 200 MeV protons and atmospheric-neutrons were performed for commercial SiC power MOSFETs with different architectures ( i.e ., planar gate, asymmetric trench and symmetric trench). The average electric fields over the depletion layer width and the electric field distributions are reported for the tested conditions and compared for the three architectures, confirming the necessity of a lower de-rating for the trench design to protect from SEB, compared to planar ones. In addition to the epitaxial layer design, the influence of other design parameters on the SEB threshold is discussed. Finally, to investigate the presence of precursor damage in the pre-SEB region, a methodology is presented and used to study the radiation-induced degradation of the channel and drift resistances of devices which survived the SEB tests.
- 14 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 70 (8) , 1844-1851
Open AccessHigh-Energy Proton and Atmospheric-Neutron Irradiations of SiC Power MOSFETs: SEB Study and Impact on Channel and Drift Resistances
Accelerated single event burnout (SEB) tests with 200 MeV protons and atmospheric-neutrons were performed for commercial SiC power MOSFETs with different architectures ( i.e ., planar gate, asymmetric trench and symmetric trench). The average electric fields over the depletion layer width and the electric field distributions are reported for the tested conditions and compared for the three architectures, confirming the necessity of a lower de-rating for the trench design to protect from SEB, compared to planar ones. In addition to the epitaxial layer design, the influence of other design parameters on the SEB threshold is discussed. Finally, to investigate the presence of precursor damage in the pre-SEB region, a methodology is presented and used to study the radiation-induced degradation of the channel and drift resistances of devices which survived the SEB tests.
- Open Access
- 31 May 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1062, 389-394
Fast Defect Mapping at the SiO2/ SiC Interface Using Confocal Photoluminescence
Electrically active defects at the SiO2/SiC interface can have detrimental effects on the device performance of SiC MOSFETs. Capacitance-or conductance-based analysis techniques are commonly used to extract the density of interface defects, despite having the disadvantage of requiring dedicated test structures for the analysis. Here, we discuss confocal sub-bandgap photoluminescence (PL) microscopy as a fast and reliable alternative to conventional electrical characterization techniques. For this purpose, the quality of the SiO2/SiC interface after post-oxidation annealing in N2O is studied both by confocal imaging as well as by the high-low and C-Ψ capacitance technique. We find excellent agreement between the optical and electrical analysis and observe a significant increase of the interface defect density for annealing temperatures below 1050 °C. Keywords: interface defect density, photoluminescence, capacitance-voltage
- 31 May 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1062, 389-394
Open AccessFast Defect Mapping at the SiO2/ SiC Interface Using Confocal Photoluminescence
Electrically active defects at the SiO2/SiC interface can have detrimental effects on the device performance of SiC MOSFETs. Capacitance-or conductance-based analysis techniques are commonly used to extract the density of interface defects, despite having the disadvantage of requiring dedicated test structures for the analysis. Here, we discuss confocal sub-bandgap photoluminescence (PL) microscopy as a fast and reliable alternative to conventional electrical characterization techniques. For this purpose, the quality of the SiO2/SiC interface after post-oxidation annealing in N2O is studied both by confocal imaging as well as by the high-low and C-Ψ capacitance technique. We find excellent agreement between the optical and electrical analysis and observe a significant increase of the interface defect density for annealing temperatures below 1050 °C. Keywords: interface defect density, photoluminescence, capacitance-voltage
- Open Access
- 31 May 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1062, 647-652
Temperature Dependence of On-State Inter-Terminal Capacitances (Cgd and Cgs) of SiC MOSFETs and Frequency Limitations of their Measurements
Inter-terminal capacitances (ITCs) have major influence on the dynamic performance of power SiC MOSFETs. Knowledge of the exact values for the ITCs is required in order to perform accurate and predictive compact model simulations of their dynamic performance. Since commercial SiC MOSFETs are capable of operating in a wide range of temperatures, it is important to know the values of ITCs in the whole temperature range of operation. Direct measurements of the ITCs with standard equipment is possible only at low current levels (i.e. in the off-state (Vgs < Vth) for Vds > 0 V), however their values in the on-state (Vgs>Vth) also influence the MOSFETs switching performance. In this work, ITCs of a planar SiC MOSFET in the on-state are studied by the means of a calibrated TCAD model, revealing substantial temperature dependence in the range of 300-450 K. In the first approximation, this temperature dependence of the ITCs can be explained by a weaker temperature dependence of the MOSFET channel resistance in comparison to its JFET and epitaxial layer resistances. In addition, it is shown that at high frequencies stray inductances of the TO-247-3 package result in a change of the extracted values of the on-state ITCs. This effect is already notable at 1 MHz.
- 31 May 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1062, 647-652
Open AccessTemperature Dependence of On-State Inter-Terminal Capacitances (Cgd and Cgs) of SiC MOSFETs and Frequency Limitations of their Measurements
Inter-terminal capacitances (ITCs) have major influence on the dynamic performance of power SiC MOSFETs. Knowledge of the exact values for the ITCs is required in order to perform accurate and predictive compact model simulations of their dynamic performance. Since commercial SiC MOSFETs are capable of operating in a wide range of temperatures, it is important to know the values of ITCs in the whole temperature range of operation. Direct measurements of the ITCs with standard equipment is possible only at low current levels (i.e. in the off-state (Vgs < Vth) for Vds > 0 V), however their values in the on-state (Vgs>Vth) also influence the MOSFETs switching performance. In this work, ITCs of a planar SiC MOSFET in the on-state are studied by the means of a calibrated TCAD model, revealing substantial temperature dependence in the range of 300-450 K. In the first approximation, this temperature dependence of the ITCs can be explained by a weaker temperature dependence of the MOSFET channel resistance in comparison to its JFET and epitaxial layer resistances. In addition, it is shown that at high frequencies stray inductances of the TO-247-3 package result in a change of the extracted values of the on-state ITCs. This effect is already notable at 1 MHz.
- Open Access
- 31 May 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1062, 346-350
Sensitivity of Dit Extraction at the SiO2/SiC Interface Using Quasi-Static Capacitance-Voltage Measurements
In this work, we compare different quasi-static capacitance-voltage measurement systems by analyzing 4H-SiC n-type MOS capacitors and studying the influence of systematic errors when extracting the interface trap density (Dit). We show that the extracted Dit strongly depends on the calculation of the surface potential due to variations of the integration constant. In addition, the ramp-rate during the quasi-static measurement is identified as a sensitive measurement parameter whose noise level is amplified in the Dit extraction.
- 31 May 2022
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 1062, 346-350
Open AccessSensitivity of Dit Extraction at the SiO2/SiC Interface Using Quasi-Static Capacitance-Voltage Measurements
In this work, we compare different quasi-static capacitance-voltage measurement systems by analyzing 4H-SiC n-type MOS capacitors and studying the influence of systematic errors when extracting the interface trap density (Dit). We show that the extracted Dit strongly depends on the calculation of the surface potential due to variations of the integration constant. In addition, the ramp-rate during the quasi-static measurement is identified as a sensitive measurement parameter whose noise level is amplified in the Dit extraction.
- Open Access
- 1 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10572-10584
Gate Capacitance Characterization of Silicon Carbide and Silicon Power mosfets Revisited
Capacitance–voltage (C–V) gate characteristics of power metal-oxide-semiconductor field-effect transistors (mosfets) play an important role in the dynamic device performance. C–V characterization of the mosfet gate structure is a necessary step for evaluating the mosfet switching behavior and calibrating lumped equivalent capacitances of mosfet compact models. This article presents a comprehensive analysis on gate C–V measurements of silicon (Si) and silicon carbide (SiC) power mosfets leading to clear measurement guidelines. The requirements on the measurement setup, the selection of equivalent models used for the mosfet capacitance extraction, and the measurement frequency range are defined and supported by an accurate C–V characterization of several Si- and SiC power mosfets. The results show that the gate-source and gate-drain capacitances should be extracted at a frequency of some 10 kHz rather than at 1 MHz, as typically adopted in datasheets, to avoid parasitic effects introduced by the measurement setup and package. Furthermore, analytical expressions for$C_\text{dg}$ and$C_\text{sg}$ were derived based on a lumped equivalent circuit, which explain the influence of the measurement setup and the package parasitics on the C–V measurements. Nonideal measurement conditions are identified and correlated to the differences in C–V extraction with either parallel or series-equivalent model. A new method is proposed to estimate the ratio of the mosfet’s on-state resistance components$R_\text{ch}$ and$R_\text{drift}$ based on the presented C–V measurement guidelines, which are applicable to all three- and four-terminal power mosfets.- 1 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (9) , 10572-10584
Open AccessGate Capacitance Characterization of Silicon Carbide and Silicon Power mosfets Revisited
Capacitance–voltage (C–V) gate characteristics of power metal-oxide-semiconductor field-effect transistors (mosfets) play an important role in the dynamic device performance. C–V characterization of the mosfet gate structure is a necessary step for evaluating the mosfet switching behavior and calibrating lumped equivalent capacitances of mosfet compact models. This article presents a comprehensive analysis on gate C–V measurements of silicon (Si) and silicon carbide (SiC) power mosfets leading to clear measurement guidelines. The requirements on the measurement setup, the selection of equivalent models used for the mosfet capacitance extraction, and the measurement frequency range are defined and supported by an accurate C–V characterization of several Si- and SiC power mosfets. The results show that the gate-source and gate-drain capacitances should be extracted at a frequency of some 10 kHz rather than at 1 MHz, as typically adopted in datasheets, to avoid parasitic effects introduced by the measurement setup and package. Furthermore, analytical expressions for$C_\text{dg}$ and$C_\text{sg}$ were derived based on a lumped equivalent circuit, which explain the influence of the measurement setup and the package parasitics on the C–V measurements. Nonideal measurement conditions are identified and correlated to the differences in C–V extraction with either parallel or series-equivalent model. A new method is proposed to estimate the ratio of the mosfet’s on-state resistance components$R_\text{ch}$ and$R_\text{drift}$ based on the presented C–V measurement guidelines, which are applicable to all three- and four-terminal power mosfets. - Open Access
- 10 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (5) , 634-641
Impact of Terrestrial Neutrons on the Reliability of SiC VD-MOSFET Technologies
Accelerated terrestrial neutron irradiations were performed on different commercial SiC power MOSFETs with planar, trench, and double-trench architectures. The results were used to calculate the failure cross sections and the failure-in-time (FIT) rates at sea level. Enhanced gate and drain leakage were observed in some devices which did not exhibit a destructive failure during the exposure. In particular, a different mechanism was observed for planar and trench gate MOSFETs, the first showing a partial gate rupture with a leakage path mostly between the drain and the gate, similar to what was previously observed with heavy ions, while the second exhibiting a complete gate rupture. The observed failure mechanisms and the postirradiation gate stress (PIGS) tests are discussed for different technologies.
- 10 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Nuclear Science
- Vol. 68 (5) , 634-641
Open AccessImpact of Terrestrial Neutrons on the Reliability of SiC VD-MOSFET Technologies
Accelerated terrestrial neutron irradiations were performed on different commercial SiC power MOSFETs with planar, trench, and double-trench architectures. The results were used to calculate the failure cross sections and the failure-in-time (FIT) rates at sea level. Enhanced gate and drain leakage were observed in some devices which did not exhibit a destructive failure during the exposure. In particular, a different mechanism was observed for planar and trench gate MOSFETs, the first showing a partial gate rupture with a leakage path mostly between the drain and the gate, similar to what was previously observed with heavy ions, while the second exhibiting a complete gate rupture. The observed failure mechanisms and the postirradiation gate stress (PIGS) tests are discussed for different technologies.
- Open Access
- 21 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (8) , 9398-9410
Accuracy of Three Interterminal Capacitance Models for SiC Power MOSFETs Under Fast Switching
This paper presents a comprehensive analysis of non-linear voltage-dependent capacitances of vertical SiC power MOSFETs with lateral channel, focusing specifically on fast switching transients. The capacitance-voltage (C-V) device characteristics, (Cgs, Cgd, Cds), being dependent on both Vgs and Vds, are extracted by means of two-dimensional Technology Computer Aided Design simulations for a commercially available device in both off- and on-state modes. Different compact models for the modelled power MOSFET are investigated, each employing a three inter-terminal capacitance model as typically used in power electronics. The performed analysis shows in detail the importance of taking into account the Cgd, Cgs and Cds voltage dependence on Vgs and Vds for fast switching transients (in the range of 10 ns) in order to accurately predict switching losses, driver losses, current and voltage slopes, as well as current and voltage delays. As direct measurements for C-Vs in dependence of both Vgs and Vds are highly demanding, the results presented in this paper increase the understanding of both the underlying effects as well as of the trade-offs between accuracy and computational complexity made by simplifying device models. This information is highly beneficial for enabling accurate and computationally efficient automated design procedures for power electronics.
- 21 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 36 (8) , 9398-9410
Open AccessAccuracy of Three Interterminal Capacitance Models for SiC Power MOSFETs Under Fast Switching
This paper presents a comprehensive analysis of non-linear voltage-dependent capacitances of vertical SiC power MOSFETs with lateral channel, focusing specifically on fast switching transients. The capacitance-voltage (C-V) device characteristics, (Cgs, Cgd, Cds), being dependent on both Vgs and Vds, are extracted by means of two-dimensional Technology Computer Aided Design simulations for a commercially available device in both off- and on-state modes. Different compact models for the modelled power MOSFET are investigated, each employing a three inter-terminal capacitance model as typically used in power electronics. The performed analysis shows in detail the importance of taking into account the Cgd, Cgs and Cds voltage dependence on Vgs and Vds for fast switching transients (in the range of 10 ns) in order to accurately predict switching losses, driver losses, current and voltage slopes, as well as current and voltage delays. As direct measurements for C-Vs in dependence of both Vgs and Vds are highly demanding, the results presented in this paper increase the understanding of both the underlying effects as well as of the trade-offs between accuracy and computational complexity made by simplifying device models. This information is highly beneficial for enabling accurate and computationally efficient automated design procedures for power electronics.