Peng Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Peng Zhou has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
Abdulhameed F. Alkhateeb
Department of Electrical and Computer Engineering, Faculty of Engineering, King Abdulaziz University, Jeddah 21589, Saudi Arabia
1 shared publication- Adil M. Ahmad
Communication Systems and Networks Research Group, Department of Information Technology, Faculty of Computing and Information Technology, King Abdulaziz University, Jeddah, Saudi Arabia
1 shared publication Ben Niu
Bohai University
1 shared publicationHuanqing Wang
Bohai University
1 shared publicationLi Rujiang
North Univ China, Sch Environm & Safety Engn, Taiyuan 030051, Shanxi, Peoples R China
1 shared publicationLiang Zhang
College of Engineering, Bohai University, Jinzhou 121013, Liaoning, China
1 shared publication
Latest Publications
- Open Access
- 1 May 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2508 (1) , 012054
Finite Element Simulation of Jet Fracture and Distribution of Grooving Charge Cover on Inner Surface
According to the analysis of the application of grooves on the inner surface of the conical charge cover in JET warhead, when the charging structure of the conical charge cover and the caliber of the charge cover are determined, Ansys LS-DYNA explicit finite element analysis software was used to study the JET fracture time, JET granulation and JET distribution caused by the groove depth and groove spacing of the inside surface of the charge cover of five groups. On this basis, parallel group experiments were conducted to analyze the data structure of the five groups. The influence law of groove structure on jet after effect on the inner surface of conical drug cover was obtained. It was found that when groove depth was 0.1mm, the effect on jet after effect was good, while the effect on jet after effect was poor when groove depth was 0.2mm. Reducing groove spacing on the inner surface would optimize jet fracture.
- 1 May 2023
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2508 (1) , 012054
Open AccessFinite Element Simulation of Jet Fracture and Distribution of Grooving Charge Cover on Inner Surface
According to the analysis of the application of grooves on the inner surface of the conical charge cover in JET warhead, when the charging structure of the conical charge cover and the caliber of the charge cover are determined, Ansys LS-DYNA explicit finite element analysis software was used to study the JET fracture time, JET granulation and JET distribution caused by the groove depth and groove spacing of the inside surface of the charge cover of five groups. On this basis, parallel group experiments were conducted to analyze the data structure of the five groups. The influence law of groove structure on jet after effect on the inner surface of conical drug cover was obtained. It was found that when groove depth was 0.1mm, the effect on jet after effect was good, while the effect on jet after effect was poor when groove depth was 0.2mm. Reducing groove spacing on the inner surface would optimize jet fracture.
- 18 May 2021
- Published by Taylor & Francis in International Journal of Systems Science
- Vol. 52 (9) , 1731-1745
Switched-observer-based adaptive output-feedback control design with unknown gain for pure-feedback switched nonlinear systems via average dwell time
This paper studies the problem of adaptive fuzzy tracking control for a class of pure-feedback switched nonlinear systems with unknown gain. First, the studied system is handled by using the mean value theorem, the initial pure-feedback nonlinear systems become affine nonlinear systems. Then, the unknown signal is handled through a linear transformation, the Nussbaum-type functions are used to design an effective controller for the processed system. To avoid the issue of ‘explosion of complexity’ caused by mean value theorem and backstepping procedure, a first-order sliding-mode differentiator is employed to simplify the calculation. Combined with the average dwell time (ADT) method, a set of switching signals are given to sure the stability of the system. The Lyapunov theorem is used to verify that all signals are semiglobal uniformly ultimately boundness (SGUUB), and the errors can be regulated arbitrarily small. Finally, simulation results show the effectiveness of the proposed method.
- 18 May 2021
- Published by Taylor & Francis in International Journal of Systems Science
- Vol. 52 (9) , 1731-1745
Switched-observer-based adaptive output-feedback control design with unknown gain for pure-feedback switched nonlinear systems via average dwell time
This paper studies the problem of adaptive fuzzy tracking control for a class of pure-feedback switched nonlinear systems with unknown gain. First, the studied system is handled by using the mean value theorem, the initial pure-feedback nonlinear systems become affine nonlinear systems. Then, the unknown signal is handled through a linear transformation, the Nussbaum-type functions are used to design an effective controller for the processed system. To avoid the issue of ‘explosion of complexity’ caused by mean value theorem and backstepping procedure, a first-order sliding-mode differentiator is employed to simplify the calculation. Combined with the average dwell time (ADT) method, a set of switching signals are given to sure the stability of the system. The Lyapunov theorem is used to verify that all signals are semiglobal uniformly ultimately boundness (SGUUB), and the errors can be regulated arbitrarily small. Finally, simulation results show the effectiveness of the proposed method.
- Open Access
- 9 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 69481-69491
Observer-Based Adaptive Fuzzy Finite-Time Control Design With Prescribed Performance for Switched Pure-Feedback Nonlinear Systems
In this paper, an adaptive fuzzy finite-time control problem for pure-feedback switched nonlinear systems with prescribed performance is investigate. By utilizing the prescribed performance technique, we mean that the system output is converge to the predefined bounds. By using the dynamic surface control (DSC) and the backstepping technique, we establish a novel adaptive fuzzy finite-time pure-feedback switching control method. In such a scheme, the Butterworth low-pass filter (LPF) is used to construct the fuzzy observer, which can estimate the immeasurable states and avoid algebraic loop problem. In accordance with the stability theory of common Lyapunov function (CLF), the designed controller can ensures that the tracking error converges to a small neighborhood of the origin in finite time. Finally, an example is given to illustrate this method and verify its validity and effectiveness.
- 9 November 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 69481-69491
Open AccessObserver-Based Adaptive Fuzzy Finite-Time Control Design With Prescribed Performance for Switched Pure-Feedback Nonlinear Systems
In this paper, an adaptive fuzzy finite-time control problem for pure-feedback switched nonlinear systems with prescribed performance is investigate. By utilizing the prescribed performance technique, we mean that the system output is converge to the predefined bounds. By using the dynamic surface control (DSC) and the backstepping technique, we establish a novel adaptive fuzzy finite-time pure-feedback switching control method. In such a scheme, the Butterworth low-pass filter (LPF) is used to construct the fuzzy observer, which can estimate the immeasurable states and avoid algebraic loop problem. In accordance with the stability theory of common Lyapunov function (CLF), the designed controller can ensures that the tracking error converges to a small neighborhood of the origin in finite time. Finally, an example is given to illustrate this method and verify its validity and effectiveness.