Fredrik R. Westlye
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Fredrik R. Westlye has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Anders Ivarsson
Department of Mechanical Engineering, Technical University of Denmark, Nils Koppels Allé Bld. 403, 2800 Kgs. Lyngby, Denmark
3 shared publications Julien Manin
Sandia National Laboratories
2 shared publicationsLyle M. Pickett
Sandia National Laboratories
2 shared publicationsScott A. Skeen
Sandia National Laboratories
2 shared publicationsDaniele Farrace
ETH Zurich
1 shared publicationEmre Cenker
King Abdullah University of Science and Technology
1 shared publication
Latest Publications
- 5 April 2016
- Published by SAE International in SAE International Journal of Engines
- Vol. 09 (2) , 883-898
A Progress Review on Soot Experiments and Modeling in the Engine Combustion Network (ECN)
The 4th Workshop of the Engine Combustion Network (ECN) was held September 5-6, 2015 in Kyoto, Japan. This manuscript presents a summary of the progress in experiments and modeling among ECN contributors leading to a better understanding of soot formation under the ECN “Spray A” configuration and some parametric variants. Relevant published and unpublished work from prior ECN workshops is reviewed. Experiments measuring soot particle size and morphology, soot volume fraction (fv), and transient soot mass have been conducted at various international institutions providing target data for improvements to computational models. Multiple modeling contributions using both the Reynolds Averaged Navier-Stokes (RANS) Equations approach and the Large-Eddy Simulation (LES) approach have been submitted. Among these, various chemical mechanisms, soot models, and turbulence-chemistry interaction (TCI) methodologies have been considered.
- 5 April 2016
- Published by SAE International in SAE International Journal of Engines
- Vol. 09 (2) , 883-898
A Progress Review on Soot Experiments and Modeling in the Engine Combustion Network (ECN)
The 4th Workshop of the Engine Combustion Network (ECN) was held September 5-6, 2015 in Kyoto, Japan. This manuscript presents a summary of the progress in experiments and modeling among ECN contributors leading to a better understanding of soot formation under the ECN “Spray A” configuration and some parametric variants. Relevant published and unpublished work from prior ECN workshops is reviewed. Experiments measuring soot particle size and morphology, soot volume fraction (fv), and transient soot mass have been conducted at various international institutions providing target data for improvements to computational models. Multiple modeling contributions using both the Reynolds Averaged Navier-Stokes (RANS) Equations approach and the Large-Eddy Simulation (LES) approach have been submitted. Among these, various chemical mechanisms, soot models, and turbulence-chemistry interaction (TCI) methodologies have been considered.
- 5 April 2016
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Penetration and combustion characterization of cavitating and non-cavitating fuel injectors under diesel engine conditions
This work investigates the effects of cavitation on spray characteristics by comparing measurements of liquid and vapor penetration as well as ignition delay and lift-off length. A smoothed-inlet, converging nozzle (nominal KS1.5) was compared to a sharp-edged nozzle (nominal K0) in a constant-volume combustion vessel under thermodynamic conditions consistent with modern compression ignition engines. Within the near-nozzle region, the K0 nozzle displayed larger radial dispersion of the liquid as compared to the KS1.5 nozzle, and shorter axial liquid penetration. Moving downstream, the KS1.5 jet growth rate increased, eventually reaching a growth rate similar to the K0 nozzle while maintaining a smaller radial width. The increasing spreading angle in the far field creates a virtual origin, or mixing offset, several millimeters downstream for the KS1.5 nozzle. Remarkably, this mixing offset appeared to globally influence the liquid penetration and lift-off stabilization location over a wide range of operating conditions. When this offset was removed, OH chemiluminescence-derived lift-off lengths for the two nozzles essentially collapsed. An Eulerian multiphase mixture model, with Large-Eddy Simulations (LES) combining internal and external flow predicted the trends in spreading angle in the region close to the injector. The K0 simulation showed cavitation zones along walls downstream of the nozzle inlet with some dispersion into the center of the jet before the nozzle exit. With a slightly diverging nozzle (as measured), the K0 simulation also indicated that low pressure zones draw ambient gas just inside the nozzle exit, which, combined with cavitation dynamics, should be considered as a potential contributor to the initial growth rate.
- 5 April 2016
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Penetration and combustion characterization of cavitating and non-cavitating fuel injectors under diesel engine conditions
This work investigates the effects of cavitation on spray characteristics by comparing measurements of liquid and vapor penetration as well as ignition delay and lift-off length. A smoothed-inlet, converging nozzle (nominal KS1.5) was compared to a sharp-edged nozzle (nominal K0) in a constant-volume combustion vessel under thermodynamic conditions consistent with modern compression ignition engines. Within the near-nozzle region, the K0 nozzle displayed larger radial dispersion of the liquid as compared to the KS1.5 nozzle, and shorter axial liquid penetration. Moving downstream, the KS1.5 jet growth rate increased, eventually reaching a growth rate similar to the K0 nozzle while maintaining a smaller radial width. The increasing spreading angle in the far field creates a virtual origin, or mixing offset, several millimeters downstream for the KS1.5 nozzle. Remarkably, this mixing offset appeared to globally influence the liquid penetration and lift-off stabilization location over a wide range of operating conditions. When this offset was removed, OH chemiluminescence-derived lift-off lengths for the two nozzles essentially collapsed. An Eulerian multiphase mixture model, with Large-Eddy Simulations (LES) combining internal and external flow predicted the trends in spreading angle in the region close to the injector. The K0 simulation showed cavitation zones along walls downstream of the nozzle inlet with some dispersion into the center of the jet before the nozzle exit. With a slightly diverging nozzle (as measured), the K0 simulation also indicated that low pressure zones draw ambient gas just inside the nozzle exit, which, combined with cavitation dynamics, should be considered as a potential contributor to the initial growth rate.
- Top Cited Papers
Experimental investigation of nitrogen based emissions from an ammonia fueled SI-engine