Yukang Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yukang Xu has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Ping Wang
National Engineering Laboratory, College of Textiles & Clothing Engineering Soochow University Suzhou China
3 shared publications - Guillaume Tartare
ENSAIT-GEMTEX Lab., Lille Université, 2 Allée Louise et Victor Champier, 59056 Roubaix, France
2 shared publications - Mulat Alubel Abtew
Department of Textile and Apparel Management, College of Arts and Science, University of Missouri, Columbia, MO 65211, USA
2 shared publications - Pascal Bruniaux
GEMTEX Laboratory, Ecole Nationale Superieure des Arts et Industries Textiles, 59056 Roubaix, France
2 shared publications - Sara Mosleh
College of Textile and Clothing Engineering, Soochow University, 178 G. J. D. Road, Suzhou 215021, China
2 shared publications - Yan Zhang
Soochow University
2 shared publications
Latest Publications
- 9 February 2022
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 31 (3) , 035025
A flexible pressure sensor based on PEDOT coated polyester nonwoven fabric for low-pressure range
Three most common methods for preparing PEDOT (poly(3,4-ethylenedioxythiophene)) are studied, including vapor phase polymerization (VPP), in-situ dipping (ISD) and solution deposition (SD) techniques. The PEDOT coated nonwoven fabric (PEDOT@NWF) composites were successfully fabricated via these three processes and have been proven to be conductive and equipped with piezoresistive properties. For each preparation method, factors that may affect product properties, such as concentrations of reagents, reaction temperature, reaction time, etc were explored to summarize the optimal parameters. The PEDOT@NWF composites prepared via different fabrication techniques were analyzed and compared through a series of tests and characterizations. The sensing performance of as-prepared pressure sensors are also been studied. The experimental results demonstrate that PEDOT@NWF prepared by VPP method (PEDOT@NWF-VPP) has the fastest response time (80 ms) and recovery time (40 ms), the composite prepared by ISD method (PEDOT@NWF-ISD) has the highest sensitivity for the pressure range less than 5 kPa (21.162 kPa −1 ) and long-term cycle stability (over 5000 cycles). Sensor utilized PEDOT@NWF-ISD as the piezoresistive layer was assembled and used to detect small pressure such as voice vibrations and air flow, implying that this designed pressure sensor has promising potential in the application of wearable electronic devices and healthcare monitors.
- 9 February 2022
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 31 (3) , 035025
A flexible pressure sensor based on PEDOT coated polyester nonwoven fabric for low-pressure range
Three most common methods for preparing PEDOT (poly(3,4-ethylenedioxythiophene)) are studied, including vapor phase polymerization (VPP), in-situ dipping (ISD) and solution deposition (SD) techniques. The PEDOT coated nonwoven fabric (PEDOT@NWF) composites were successfully fabricated via these three processes and have been proven to be conductive and equipped with piezoresistive properties. For each preparation method, factors that may affect product properties, such as concentrations of reagents, reaction temperature, reaction time, etc were explored to summarize the optimal parameters. The PEDOT@NWF composites prepared via different fabrication techniques were analyzed and compared through a series of tests and characterizations. The sensing performance of as-prepared pressure sensors are also been studied. The experimental results demonstrate that PEDOT@NWF prepared by VPP method (PEDOT@NWF-VPP) has the fastest response time (80 ms) and recovery time (40 ms), the composite prepared by ISD method (PEDOT@NWF-ISD) has the highest sensitivity for the pressure range less than 5 kPa (21.162 kPa −1 ) and long-term cycle stability (over 5000 cycles). Sensor utilized PEDOT@NWF-ISD as the piezoresistive layer was assembled and used to detect small pressure such as voice vibrations and air flow, implying that this designed pressure sensor has promising potential in the application of wearable electronic devices and healthcare monitors.
- 23 November 2021
- Published by Springer Nature in Cellulose
- Vol. 29 (2) , 835-848
Characterization of mechanical properties of jute/PLA composites containing nano SiO2 modified by coupling agents
- 23 November 2021
- Published by Springer Nature in Cellulose
- Vol. 29 (2) , 835-848
Characterization of mechanical properties of jute/PLA composites containing nano SiO2 modified by coupling agents
- Open Access
- 12 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (22) , 10655
Developments of Adapted Clothing for Physically Disabled People with Scoliosis Using 3D Geometrical Model
Scoliosis is a deformity of the spine that causes disorders of the rib cage. This makes it difficult to design clothes for affected people without following the shape of the rib cage. This paper presents a new 3D clothing design method based on virtual reality for women with physical disabilities such as scoliosis. The current design method is a variation of the draping techniques commonly used by fashion designers to design clothes on a mannequin or human body. However, the current design process highly considers the skeleton and body scan of the person. The skeleton is used to detect the anthropometric points of the patient, while the body scan allows us to detect the morphological contours at the onset of scoliosis. Thus, both allow us to accurately track the patient’s morphology and atypical shape. The position of the morphological contours is indicated by reference marks that are closely associated with the skeleton. This helps to automatically adapt the garment to the evolution of the patient’s pathology over time. The process of creating the 3D garment was processed based on the 3D model of the thorax, which helps to easily determine the anthropometric points and the morphological curves. Using this data, the geometrical model of the garment could be created with 3D ease allowances. The 2D block pattern was then obtained by flattening the 3D patterns using flattening methods. Finally, various tests were performed considering the evolution of pathology to predict the future garment. These tests validate our geometrical model of the garment with 3D ease allowances by comparing the results with previous work.
- 12 November 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (22) , 10655
Open AccessDevelopments of Adapted Clothing for Physically Disabled People with Scoliosis Using 3D Geometrical Model
Scoliosis is a deformity of the spine that causes disorders of the rib cage. This makes it difficult to design clothes for affected people without following the shape of the rib cage. This paper presents a new 3D clothing design method based on virtual reality for women with physical disabilities such as scoliosis. The current design method is a variation of the draping techniques commonly used by fashion designers to design clothes on a mannequin or human body. However, the current design process highly considers the skeleton and body scan of the person. The skeleton is used to detect the anthropometric points of the patient, while the body scan allows us to detect the morphological contours at the onset of scoliosis. Thus, both allow us to accurately track the patient’s morphology and atypical shape. The position of the morphological contours is indicated by reference marks that are closely associated with the skeleton. This helps to automatically adapt the garment to the evolution of the patient’s pathology over time. The process of creating the 3D garment was processed based on the 3D model of the thorax, which helps to easily determine the anthropometric points and the morphological curves. Using this data, the geometrical model of the garment could be created with 3D ease allowances. The 2D block pattern was then obtained by flattening the 3D patterns using flattening methods. Finally, various tests were performed considering the evolution of pathology to predict the future garment. These tests validate our geometrical model of the garment with 3D ease allowances by comparing the results with previous work.
- Open Access
- 10 November 2021
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 11 (58) , 36596-36606
Manufacturing of polytetrafluoroethylene fine fibers by waterjet impacting
The waterjet impacting technology was introduced to split PTFE split-film fibers again to manufacture fine fibers for applications in the air purification field.
- 10 November 2021
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 11 (58) , 36596-36606
Open AccessManufacturing of polytetrafluoroethylene fine fibers by waterjet impacting
The waterjet impacting technology was introduced to split PTFE split-film fibers again to manufacture fine fibers for applications in the air purification field.
- Open Access
- 17 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (10) , 4545
3D Digital Adaptive Thorax Modelling of Peoples with Spinal Disabilities: Applications for Performance Clothing Design
Peoples with spinal disability face a huge problem in the design and development of ergonomically fitted and comfortable clothing. Various research studies on the design and developments of functional clothing for scoliosis patients consider their morphological shapes. However, developing appropriate models of the complicated and deformed anatomical shape of the patient in 3D digitization technologies makes it possible to design a comfortable and fitted garment. The current paper proposes a method for developing a fully parametric 3D adaptive model of the thorax of a patient suffering from scoliosis. The model is designed from the spine and follows the deformation of the spine to adapt the thorax skeleton according to the temporal evolution of the spinal column deformation. The integration of the model of the thorax, adjusted to the patient’s data, enables the chain of acquisition, processing, and global model to be validated. The fit of the model could be improved for the different bones and it is possible to modify the angles of the spine to see the evolution of the disease. The developed model greatly helps to further detect anthropometric points from certain bone parts of the skeleton to design a basic bodice adapted to the patient’s evolving morphology.
- 17 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (10) , 4545
Open Access3D Digital Adaptive Thorax Modelling of Peoples with Spinal Disabilities: Applications for Performance Clothing Design
Peoples with spinal disability face a huge problem in the design and development of ergonomically fitted and comfortable clothing. Various research studies on the design and developments of functional clothing for scoliosis patients consider their morphological shapes. However, developing appropriate models of the complicated and deformed anatomical shape of the patient in 3D digitization technologies makes it possible to design a comfortable and fitted garment. The current paper proposes a method for developing a fully parametric 3D adaptive model of the thorax of a patient suffering from scoliosis. The model is designed from the spine and follows the deformation of the spine to adapt the thorax skeleton according to the temporal evolution of the spinal column deformation. The integration of the model of the thorax, adjusted to the patient’s data, enables the chain of acquisition, processing, and global model to be validated. The fit of the model could be improved for the different bones and it is possible to modify the angles of the spine to see the evolution of the disease. The developed model greatly helps to further detect anthropometric points from certain bone parts of the skeleton to design a basic bodice adapted to the patient’s evolving morphology.