Mehrdad Mousapour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mehrdad Mousapour has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Mika Salmi
Aalto University
4 shared publications - Jouni Partanen
Department of Mechanical Engineering, Aalto University, Otakaari 4, 02150 Espoo, Finland
2 shared publications - S. Siddharth Kumar
Aalto University
2 shared publications - Ari Jokilaakso
Department of Chemical and Metallurgical Engineering, School of Chemical Engineering, Aalto University, Espoo, Finland
1 shared publication - Jan Sher Akmal
Aalto University
1 shared publication - Jari Aromaa
Aalto University
1 shared publication
Latest Publications
- Open Access
- 21 May 2026
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 21 (1)
4D-printed shape memory alloy–polymer hybrid composites with tunable bidirectional actuation
- 21 May 2026
- Published by Taylor & Francis in Virtual and Physical Prototyping
- Vol. 21 (1)
Open Access4D-printed shape memory alloy–polymer hybrid composites with tunable bidirectional actuation
- Open Access
- 7 November 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 289
3d printing of a continuous carbon fiber reinforced bronze-matrix composite using material extrusion
- 7 November 2024
- Published by Elsevier in Composites Part B: Engineering
- Vol. 289
Open Access3d printing of a continuous carbon fiber reinforced bronze-matrix composite using material extrusion
- Open Access
- 3 November 2023
- Published by Elsevier in Additive Manufacturing
- Vol. 78
NiTiCu alloy from elemental and alloyed powders using vat photopolymerization additive manufacturing
- 3 November 2023
- Published by Elsevier in Additive Manufacturing
- Vol. 78
Open AccessNiTiCu alloy from elemental and alloyed powders using vat photopolymerization additive manufacturing
- Open Access
- 25 October 2021
- Published by MDPI AG in Corrosion and Materials Degradation
- Vol. 2 (4) , 625-640
The Oxidation of Copper in Air at Temperatures up to 100 °C
The aim of this study was to investigate the oxidation kinetics of copper at low temperatures (60 °C to 100 °C) in air by isothermal thermogravimetric analysis (TGA) and quartz crystal microbalance (QCM). The weight change in thermogravimetric tests showed periodic weight increase and decrease. In thermogravimetric tests the mass of the copper sample increased until the oxidation gradually slowed down and finally started to decrease due to cracking and spalling of the oxide formed on the surface. In QCM tests using electrodeposited copper film, the weight change was rapid at the beginning but slowed to a linear relationship after few minutes. Temperature and exposure time appeared to have a large effect on oxide film thickness and composition. With QCM, oxidation at 60–80 °C produced less than 40 nm films in 10 days. Oxidation at 90–100 °C produced 40 nm thick films in a day and over 100 nm films in a week. Although SEM-EDS analyses in TGA tests indicated that oxygen was adsorbed on the copper surface, neither XRD patterns nor Raman spectroscopy measurements showed any trace of Cu2O or CuO formation on the copper surface. Electrochemical reduction analysis of oxidized massive copper samples indicated that the oxide film is mostly Cu2O, and CuO develops only after several days at 90–100 °C.
- 25 October 2021
- Published by MDPI AG in Corrosion and Materials Degradation
- Vol. 2 (4) , 625-640
Open AccessThe Oxidation of Copper in Air at Temperatures up to 100 °C
The aim of this study was to investigate the oxidation kinetics of copper at low temperatures (60 °C to 100 °C) in air by isothermal thermogravimetric analysis (TGA) and quartz crystal microbalance (QCM). The weight change in thermogravimetric tests showed periodic weight increase and decrease. In thermogravimetric tests the mass of the copper sample increased until the oxidation gradually slowed down and finally started to decrease due to cracking and spalling of the oxide formed on the surface. In QCM tests using electrodeposited copper film, the weight change was rapid at the beginning but slowed to a linear relationship after few minutes. Temperature and exposure time appeared to have a large effect on oxide film thickness and composition. With QCM, oxidation at 60–80 °C produced less than 40 nm films in 10 days. Oxidation at 90–100 °C produced 40 nm thick films in a day and over 100 nm films in a week. Although SEM-EDS analyses in TGA tests indicated that oxygen was adsorbed on the copper surface, neither XRD patterns nor Raman spectroscopy measurements showed any trace of Cu2O or CuO formation on the copper surface. Electrochemical reduction analysis of oxidized massive copper samples indicated that the oxide film is mostly Cu2O, and CuO develops only after several days at 90–100 °C.
- Open Access
- 1 July 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 67, 438-446
Feasibility study of producing multi-metal parts by Fused Filament Fabrication (FFF) technique
- 1 July 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 67, 438-446
Open AccessFeasibility study of producing multi-metal parts by Fused Filament Fabrication (FFF) technique