Debin Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Debin Wang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Chao Li
School of Infrastructure Engineering, Dalian University of Technology, Dalian, China
2 shared publications - Guoxi Fan
Ocean University of China
2 shared publications - Hong-Nan Li
School of Infrastructure Engineering, Dalian University of Technology, Dalian 116024, P. R. China
2 shared publications - Mao Gao
Department of Civil Engineering, College of Transportation Engineering, Dalian Maritime University, Dalian 116026, China
2 shared publications - Rou-Han Li
Department of Civil Engineering, College of Transportation Engineering, Dalian Maritime University, Dalian 116026, China
2 shared publications - Wenming Wang
School of Civil Engineering, Shandong Jianzhu University, Jinan 250101, China
2 shared publications
Latest Publications
- Open Access
- 16 February 2026
- Published by Elsevier in SSRN Electronic Journal
Experimental Study and Numerical Simulation on Seismic Performance of a Self-Centering Deformation-Amplified Torsional Steel Tube Damper
To address the limitations of conventional metallic dampers, which exhibit difficulty in yielding under small deformations and significant residual deformation under large deformations, this paper proposes a novel self-centering deformation-amplified torsional steel tube damper (SC-DATSTD). The structural configuration, working mechanism, and assembly process of the proposed damper are described in detail. Quasi-static cyclic loading tests were conducted to investigate its hysteretic behavior, with a focus on key performance indicators, including failure mode, load-bearing characteristics, energy dissipation efficiency, and self-centering capability. Furthermore, a refined finite element model was developed. Experimental results indicate that the hysteresis curves exhibit a distinct asymmetric flag-shaped pattern. Reducing the initial amplification angle effectively enhances both the deformation and load-bearing amplification factors of the energy-dissipation system, significantly improves its energy-dissipation performance under low displacement levels, and increases the equivalent damping ratio by up to 43.3%, while maintaining stable self-centering capacity. Numerical simulation results show good agreement with experimental data, with maximum load errors across all loading stages remaining within 10% and nearly identical tension-compression load ratios. The reduction in the initial amplification angle leads to markedly increased plastic deformation in the energy-dissipation steel tubes, consistent with experimentally observed energy dissipation trends, thereby confirming that the finite element model accurately captures the working mechanism and hysteretic behavior of the damper.
- 16 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessExperimental Study and Numerical Simulation on Seismic Performance of a Self-Centering Deformation-Amplified Torsional Steel Tube Damper
To address the limitations of conventional metallic dampers, which exhibit difficulty in yielding under small deformations and significant residual deformation under large deformations, this paper proposes a novel self-centering deformation-amplified torsional steel tube damper (SC-DATSTD). The structural configuration, working mechanism, and assembly process of the proposed damper are described in detail. Quasi-static cyclic loading tests were conducted to investigate its hysteretic behavior, with a focus on key performance indicators, including failure mode, load-bearing characteristics, energy dissipation efficiency, and self-centering capability. Furthermore, a refined finite element model was developed. Experimental results indicate that the hysteresis curves exhibit a distinct asymmetric flag-shaped pattern. Reducing the initial amplification angle effectively enhances both the deformation and load-bearing amplification factors of the energy-dissipation system, significantly improves its energy-dissipation performance under low displacement levels, and increases the equivalent damping ratio by up to 43.3%, while maintaining stable self-centering capacity. Numerical simulation results show good agreement with experimental data, with maximum load errors across all loading stages remaining within 10% and nearly identical tension-compression load ratios. The reduction in the initial amplification angle leads to markedly increased plastic deformation in the energy-dissipation steel tubes, consistent with experimentally observed energy dissipation trends, thereby confirming that the finite element model accurately captures the working mechanism and hysteretic behavior of the damper.
- Open Access
Seismic Performance Research on a Graded-Yielding Metal Brace with Self-Centering Functions
With the aim of achieving a graded-protection braced frame structure and minimizing the excessive residual deformation of traditional metal dampers under intense seismic action, a graded-yield-type metal self-centering brace (SC-GYMB) is proposed. The brace is composed of X-shaped and U-shaped steel plates with different yield point displacements, which jointly dissipate energy. Additionally, it employs a composite disc spring as a self-centering element to provide restoring force for the brace. The brace’s basic structure and working mechanism are described, and the theoretical model for its restoring force is derived. The ABAQUS finite element software (ABAQUS 2021) is utilized to investigate the hysteretic performance of the SC-GYMB under low-cycle reciprocating load, while thoroughly discussing the influence of various model parameters on its key mechanical behavior. The results demonstrate a strong agreement between the theoretical restoring force model and the numerical simulation results. The hysteretic curves of the braces exhibit a distinct “flag” characteristic, indicating excellent energy dissipation capacity and self-centering performance. Moreover, these curves display a hierarchical yield behavior that satisfies the seismic performance requirements for different intensity earthquakes. The deformation mechanism of X-shaped steel sheets transitions from bending deformation during the initial loading stage to tensile deformation in the subsequent loading stage. Increasing the initial pre-compression force of the combined disc spring enhances the restoration performance of the brace. Augmenting the thickness of X-shaped or U-shaped steel sheets modifies the displacement and load at both the first and second yield points, thereby enhancing energy dissipation capacity and bearing capacity of the brace; however, it also leads to increased residual deformation.
Open AccessSeismic Performance Research on a Graded-Yielding Metal Brace with Self-Centering Functions
With the aim of achieving a graded-protection braced frame structure and minimizing the excessive residual deformation of traditional metal dampers under intense seismic action, a graded-yield-type metal self-centering brace (SC-GYMB) is proposed. The brace is composed of X-shaped and U-shaped steel plates with different yield point displacements, which jointly dissipate energy. Additionally, it employs a composite disc spring as a self-centering element to provide restoring force for the brace. The brace’s basic structure and working mechanism are described, and the theoretical model for its restoring force is derived. The ABAQUS finite element software (ABAQUS 2021) is utilized to investigate the hysteretic performance of the SC-GYMB under low-cycle reciprocating load, while thoroughly discussing the influence of various model parameters on its key mechanical behavior. The results demonstrate a strong agreement between the theoretical restoring force model and the numerical simulation results. The hysteretic curves of the braces exhibit a distinct “flag” characteristic, indicating excellent energy dissipation capacity and self-centering performance. Moreover, these curves display a hierarchical yield behavior that satisfies the seismic performance requirements for different intensity earthquakes. The deformation mechanism of X-shaped steel sheets transitions from bending deformation during the initial loading stage to tensile deformation in the subsequent loading stage. Increasing the initial pre-compression force of the combined disc spring enhances the restoration performance of the brace. Augmenting the thickness of X-shaped or U-shaped steel sheets modifies the displacement and load at both the first and second yield points, thereby enhancing energy dissipation capacity and bearing capacity of the brace; however, it also leads to increased residual deformation.
- Open Access
Research on the Mechanical Model and Hysteresis Performance of a New Mild Steel-Rotational Friction Hybrid Self-Centering Damper
A mild steel-friction self-centering damper with a hybrid energy-dissipation mechanism (MS-SCFD) was proposed, which consisted of a mild steel, frictional, dual-energy-dissipation system and a disc spring resetting system. The structure and principle of the MS-SCFD were explained in detail while the restoring force model was established. The hysteretic behavior of the MS-SCFD under low-cycle reciprocating loading was modeled. Then, the influence of parameters such as the disc spring preload, the friction coefficient, and the soft-steel thickness on the mechanical properties of the MS-SCFD was investigated. The results indicate that the simulation results are basically consistent with the theoretical prediction results, with a maximum error of only 9.46% for the key points of bearing capacity. Since the MS-SCFD is provided with a hysteretic curve in the typical flag type, it will obtain the capacity of excellent self-centering performance. It can effectively enhance the stiffness, bearing capacity, and self-centering capability of the damper after the pre-pressure of the disc spring is increased. The energy-dissipation capacity of the MS-SCFD increases with the increase in the friction coefficient. However, it also increases the residual deformation of the MS-SCFD. The energy dissipation of the MS-SCFD is particularly sensitive to the thickness of mild steel. After being loaded, all components of the MS-SCFD are not damaged except for the plastic deformation caused by the yielding of the mild steel. The normal function of the MS-SCFD can be restored simply by replacing the mild steel plates after the earthquake. Therefore, it can significantly enhance the economy and applicability of the damper.
Open AccessResearch on the Mechanical Model and Hysteresis Performance of a New Mild Steel-Rotational Friction Hybrid Self-Centering Damper
A mild steel-friction self-centering damper with a hybrid energy-dissipation mechanism (MS-SCFD) was proposed, which consisted of a mild steel, frictional, dual-energy-dissipation system and a disc spring resetting system. The structure and principle of the MS-SCFD were explained in detail while the restoring force model was established. The hysteretic behavior of the MS-SCFD under low-cycle reciprocating loading was modeled. Then, the influence of parameters such as the disc spring preload, the friction coefficient, and the soft-steel thickness on the mechanical properties of the MS-SCFD was investigated. The results indicate that the simulation results are basically consistent with the theoretical prediction results, with a maximum error of only 9.46% for the key points of bearing capacity. Since the MS-SCFD is provided with a hysteretic curve in the typical flag type, it will obtain the capacity of excellent self-centering performance. It can effectively enhance the stiffness, bearing capacity, and self-centering capability of the damper after the pre-pressure of the disc spring is increased. The energy-dissipation capacity of the MS-SCFD increases with the increase in the friction coefficient. However, it also increases the residual deformation of the MS-SCFD. The energy dissipation of the MS-SCFD is particularly sensitive to the thickness of mild steel. After being loaded, all components of the MS-SCFD are not damaged except for the plastic deformation caused by the yielding of the mild steel. The normal function of the MS-SCFD can be restored simply by replacing the mild steel plates after the earthquake. Therefore, it can significantly enhance the economy and applicability of the damper.
- Open Access
Experimental, Theoretical and Numerical Research Progress on Dynamic Behaviors of RC Structural Members
In this paper, research on dynamic behaviors of RC structural members was reviewed using experimental, theoretical and numerical perspectives. First, in a basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests were presented. Then, theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforced steel and proposed modified models of dynamic behavior parameters at the structural member level were summarized. Finally, the available modeling approach and method for incorporating dynamic effects in numerical simulations of RC structures were reviewed. Moreover, the work involved a brief introduction to a dynamic hysteretic model established using experimental data, which was designed to provide an alternative approach to the commonly-used DIF method for considering these dynamic effects. This paper, therefore, aimed to provide a valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures—while also putting forward issues that need to be addressed by future work.
Open AccessExperimental, Theoretical and Numerical Research Progress on Dynamic Behaviors of RC Structural Members
In this paper, research on dynamic behaviors of RC structural members was reviewed using experimental, theoretical and numerical perspectives. First, in a basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests were presented. Then, theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforced steel and proposed modified models of dynamic behavior parameters at the structural member level were summarized. Finally, the available modeling approach and method for incorporating dynamic effects in numerical simulations of RC structures were reviewed. Moreover, the work involved a brief introduction to a dynamic hysteretic model established using experimental data, which was designed to provide an alternative approach to the commonly-used DIF method for considering these dynamic effects. This paper, therefore, aimed to provide a valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures—while also putting forward issues that need to be addressed by future work.
- Open Access
- 17 April 2023
- Published by MDPI AG in Preprints.org
Experimental, Theoretical and Numerical Research Progress on Dynamic Behaviors of RC Structural Members
In this paper, the research progress on dynamic behaviors of RC structural members is reviewed from experimental, theoretical and numerical perspectives. Firstly, the basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests are presented. Then the theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforcing steel and the proposed modified models of dynamic behavior parameter at the structural member level are summarized. Finally, the available modelling approach and the method for incorporating the dynamic effect in numerical simulation of RC structures are reviewed. Moreover, a brief introduction is made to the dynamic hysteretic model established on the experimental data, which provides an alternative approach to consider the dynamic effect beside the commonly used DIF method. This paper provides valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures, and also puts forward some issues that need to be solved in the future research works..
- 17 April 2023
- Published by MDPI AG in Preprints.org
Open AccessExperimental, Theoretical and Numerical Research Progress on Dynamic Behaviors of RC Structural Members
In this paper, the research progress on dynamic behaviors of RC structural members is reviewed from experimental, theoretical and numerical perspectives. Firstly, the basic overview, measurement methods, main conclusions and current limitations of available dynamic loading tests are presented. Then the theoretical studies on the dynamic constitutive models of RC materials, the dynamic increase factor (DIF) model for concrete and reinforcing steel and the proposed modified models of dynamic behavior parameter at the structural member level are summarized. Finally, the available modelling approach and the method for incorporating the dynamic effect in numerical simulation of RC structures are reviewed. Moreover, a brief introduction is made to the dynamic hysteretic model established on the experimental data, which provides an alternative approach to consider the dynamic effect beside the commonly used DIF method. This paper provides valuable reference for experimental studies and numerical simulations on the dynamic behaviors of RC structures, and also puts forward some issues that need to be solved in the future research works..
- 18 February 2023
- Published by Springer Nature in International Journal of Civil Engineering
- Vol. 21 (5) , 857-874
Experimental Research and Theoretical Analysis of Mechanical Behavior of Torsional Metallic Damper
- 18 February 2023
- Published by Springer Nature in International Journal of Civil Engineering
- Vol. 21 (5) , 857-874
Experimental Research and Theoretical Analysis of Mechanical Behavior of Torsional Metallic Damper
- Open Access
- 18 January 2019
- Published by DEStech Publications in DEStech Transactions on Engineering and Technology Research
- No. eeec
Experimental Study on Dynamic Bond Properties Between Reinforcing Steel Bar and Concrete
Experimental Study on Dynamic Bond Properties Between Reinforcing Steel Bar and Concrete
- 18 January 2019
- Published by DEStech Publications in DEStech Transactions on Engineering and Technology Research
- No. eeec
Open AccessExperimental Study on Dynamic Bond Properties Between Reinforcing Steel Bar and Concrete
Experimental Study on Dynamic Bond Properties Between Reinforcing Steel Bar and Concrete
- 10 June 2013
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 32 (23) , 1793-1806
Experimental study on dynamic mechanical properties of reinforced concrete column
This article focuses on the study of the mechanical properties of the reinforced concrete columns with different specifications under different loading rates. The dynamic properties of the reinforced concrete column under bidirectional loading conditions are investigated as well. The initial stiffness, stiffness degradation, strength degradation, ductility, ultimate resistance capacity, yield resistance capacity, energy absorption and damage of members are analyzed according to experimental results. Based on the above analyses, some significant conclusions are obtained for engineering practice.
- 10 June 2013
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 32 (23) , 1793-1806
Experimental study on dynamic mechanical properties of reinforced concrete column
This article focuses on the study of the mechanical properties of the reinforced concrete columns with different specifications under different loading rates. The dynamic properties of the reinforced concrete column under bidirectional loading conditions are investigated as well. The initial stiffness, stiffness degradation, strength degradation, ductility, ultimate resistance capacity, yield resistance capacity, energy absorption and damage of members are analyzed according to experimental results. Based on the above analyses, some significant conclusions are obtained for engineering practice.