Christopher de Leeuwe
Research Subjects
Christopher de Leeuwe has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Adam Zaidi
5 shared publications- Vincenzo Spallina
Department of Chemical Engineering, University of Manchester, Manchester, M13 9PL, UK
4 shared publications - Angelos M. Efstathiou
Department of Chemistry, Heterogeneous Catalysis Laboratory
2 shared publications - Ian Saxley Metcalfe
School of Engineering, Newcastle University, Newcastle upon Tyne NE1 7RU, UK
2 shared publications - Mohamed Galal Hassan
The University of Southampton
2 shared publications - Syed Zaheer Abbas
School of Chemistry and Chemical Engineering, Faculty of Engineering and Physical Sciences, University of Southampton, Southampton SO17 1BJ, UK
2 shared publications
Latest Publications
- Open Access
- 12 September 2026
- Published by Elsevier in Molecular Catalysis
- Vol. 604
Fuel-assisted thermochemical CO production from CO2 using Co- and Ni-doped LaSrMn-based perovskite oxides
- 12 September 2026
- Published by Elsevier in Molecular Catalysis
- Vol. 604
Open AccessFuel-assisted thermochemical CO production from CO2 using Co- and Ni-doped LaSrMn-based perovskite oxides
- Open Access
- 27 May 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (22) , 11618-11630
Fixed Bed Chemical Looping beyond Gas Switching: Application to Dynamic Industrial Waste Gas Conversion
This article presents first-of-their-kind investigations on fixed bed chemical looping as a means of converting dynamic industrial process waste gases containing CO, H2, or hydrocarbons to a product suitable for delivery to a CO2 separation system, without dilution by excess combustion air or flaring outside of process lines. The electric arc furnace (EAF) is used as a case study for its extreme variability in composition and flow rates, and a sample process configuration is presented. Copper- and iron-based oxygen carrier (OC) materials are tested using batched synthetic CO-rich EAF off-gas at the bench scale in a fixed bed reactor to assess the operating limits of the materials with respect to temperature, flow rate, and OC conversion. Results show high OC utilization is possible before breakthrough, with potential for increases in higher-temperature reactors. External mass transfer resistances and possible flow channeling were observed in the bench-scale system and their elimination in pilot and full-scale reactors is discussed. Coke deposition occurred on the iron-based material and resulted in minor deactivation; however, pathways for elimination via temperature management and the use of a small supply of steam with feed gases are described. A selection of processes with dynamic product or waste streams that may benefit from fixed bed chemical looping as a waste treatment or emissions reduction system are introduced, highlighting the absence of treatment methods in use. A fixed bed chemical looping reactor configuration utilizing external heat removal is proposed for load balancing.
- 27 May 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (22) , 11618-11630
Open AccessFixed Bed Chemical Looping beyond Gas Switching: Application to Dynamic Industrial Waste Gas Conversion
This article presents first-of-their-kind investigations on fixed bed chemical looping as a means of converting dynamic industrial process waste gases containing CO, H2, or hydrocarbons to a product suitable for delivery to a CO2 separation system, without dilution by excess combustion air or flaring outside of process lines. The electric arc furnace (EAF) is used as a case study for its extreme variability in composition and flow rates, and a sample process configuration is presented. Copper- and iron-based oxygen carrier (OC) materials are tested using batched synthetic CO-rich EAF off-gas at the bench scale in a fixed bed reactor to assess the operating limits of the materials with respect to temperature, flow rate, and OC conversion. Results show high OC utilization is possible before breakthrough, with potential for increases in higher-temperature reactors. External mass transfer resistances and possible flow channeling were observed in the bench-scale system and their elimination in pilot and full-scale reactors is discussed. Coke deposition occurred on the iron-based material and resulted in minor deactivation; however, pathways for elimination via temperature management and the use of a small supply of steam with feed gases are described. A selection of processes with dynamic product or waste streams that may benefit from fixed bed chemical looping as a waste treatment or emissions reduction system are introduced, highlighting the absence of treatment methods in use. A fixed bed chemical looping reactor configuration utilizing external heat removal is proposed for load balancing.
- Open Access
- 5 October 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (6)
Performance evaluation of novel Ca/Mn-doped perovskite as a multifunctional material in chemical looping reverse water gas shift process for low-carbon fuels
- 5 October 2025
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 13 (6)
Open AccessPerformance evaluation of novel Ca/Mn-doped perovskite as a multifunctional material in chemical looping reverse water gas shift process for low-carbon fuels
- Open Access
- 13 November 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 94, 535-544
Experimental investigation of La0.6Sr0.4FeO3 -δ pellets as oxygen carriers for chemical-looping applications
- 13 November 2024
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 94, 535-544
Open AccessExperimental investigation of La0.6Sr0.4FeO3 -δ pellets as oxygen carriers for chemical-looping applications
- Open Access
- 16 October 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (21) , 20669-20680
Packed-Bed Chemical Looping Reforming for Renewable Syngas Production from Glycerol with Ni_Fe-Based Oxygen Carriers/Catalysts
A chemical looping (CL) reactor can provide the energy required to produce syngas from the reforming of glycerol. This can be done through the dynamic operation of packed-bed (PB) reactors that consecutively cycle in a three-stage process that includes oxidation, reduction, and a reforming stage. In this work, Ni-/Fe-based materials were synthesized, characterized, and tested as oxygen carriers and glycerol reforming catalysts during chemical looping reforming in packed-bed (CLR-PB) reactors. Two materials were prepared via coprecipitation/impregnation with different Ni loads (4.3 and 12 wt %) and similar Fe loadings (9.9 and 8.5% wt) and later on granulated to produce particles in a size cut of 0.6–1 mm. The materials presented high catalytic activity in a wide range of reforming temperatures (650–800 °C), being able to achieve over 95% glycerol-to-gas molar conversion in very short gas/solid contact times and at relevant conditions suitable for process scale-up. The results indicated that it is possible to produce materials with a low Ni load, which present sufficient catalytic activity and thermochemical capacity thanks to the presence of Fe, to operate under the glycerol CLR-PB configuration.
- 16 October 2024
- Published by American Chemical Society (ACS) in Energy & Fuels
- Vol. 38 (21) , 20669-20680
Open AccessPacked-Bed Chemical Looping Reforming for Renewable Syngas Production from Glycerol with Ni_Fe-Based Oxygen Carriers/Catalysts
A chemical looping (CL) reactor can provide the energy required to produce syngas from the reforming of glycerol. This can be done through the dynamic operation of packed-bed (PB) reactors that consecutively cycle in a three-stage process that includes oxidation, reduction, and a reforming stage. In this work, Ni-/Fe-based materials were synthesized, characterized, and tested as oxygen carriers and glycerol reforming catalysts during chemical looping reforming in packed-bed (CLR-PB) reactors. Two materials were prepared via coprecipitation/impregnation with different Ni loads (4.3 and 12 wt %) and similar Fe loadings (9.9 and 8.5% wt) and later on granulated to produce particles in a size cut of 0.6–1 mm. The materials presented high catalytic activity in a wide range of reforming temperatures (650–800 °C), being able to achieve over 95% glycerol-to-gas molar conversion in very short gas/solid contact times and at relevant conditions suitable for process scale-up. The results indicated that it is possible to produce materials with a low Ni load, which present sufficient catalytic activity and thermochemical capacity thanks to the presence of Fe, to operate under the glycerol CLR-PB configuration.
- 27 May 2019
- Published by Springer Nature in Nature Chemistry
- Vol. 11 (7) , 638-643
Overcoming chemical equilibrium limitations using a thermodynamically reversible chemical reactor
All real processes, be they chemical, mechanical or electrical, are thermodynamically irreversible and therefore suffer from thermodynamic losses. Here, we report the design and operation of a chemical reactor capable of approaching thermodynamically reversible operation. The reactor was employed for hydrogen production via the water–gas shift reaction, an important route to ‘green’ hydrogen. The reactor avoids mixing reactant gases by transferring oxygen from the (oxidizing) water stream to the (reducing) carbon monoxide stream via a solid-state oxygen reservoir consisting of a perovskite phase (La0.6Sr0.4FeO3-δ). This reservoir is able to remain close to equilibrium with the reacting gas streams because of its variable degree of non-stoichiometry and thus develops a ‘chemical memory’ that we employ to approach reversibility. We demonstrate this memory using operando, spatially resolved, real-time, high-resolution X-ray powder diffraction on a working reactor. The design leads to a reactor unconstrained by overall chemical equilibrium limitations, which can produce essentially pure hydrogen and carbon dioxide as separate product streams.
- 27 May 2019
- Published by Springer Nature in Nature Chemistry
- Vol. 11 (7) , 638-643
Overcoming chemical equilibrium limitations using a thermodynamically reversible chemical reactor
All real processes, be they chemical, mechanical or electrical, are thermodynamically irreversible and therefore suffer from thermodynamic losses. Here, we report the design and operation of a chemical reactor capable of approaching thermodynamically reversible operation. The reactor was employed for hydrogen production via the water–gas shift reaction, an important route to ‘green’ hydrogen. The reactor avoids mixing reactant gases by transferring oxygen from the (oxidizing) water stream to the (reducing) carbon monoxide stream via a solid-state oxygen reservoir consisting of a perovskite phase (La0.6Sr0.4FeO3-δ). This reservoir is able to remain close to equilibrium with the reacting gas streams because of its variable degree of non-stoichiometry and thus develops a ‘chemical memory’ that we employ to approach reversibility. We demonstrate this memory using operando, spatially resolved, real-time, high-resolution X-ray powder diffraction on a working reactor. The design leads to a reactor unconstrained by overall chemical equilibrium limitations, which can produce essentially pure hydrogen and carbon dioxide as separate product streams.