Muhammad Khalid Malik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Muhammad Khalid Malik has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Dimitrios Chronopoulos
Department of Mechanical Engineering & Mecha(tro)nic System Dynamics (LMSD), KU Leuven, 9000 Gent, Belgium
3 shared publications - Gerardo Aranguren
Electronic Design Group, University of the Basque Country (UPV/EHU), 48013 Bilbao, Spain
2 shared publications - Josu Etxaniz
Electronic Design Group, University of the Basque Country (UPV/EHU), 48013 Bilbao, Spain
2 shared publications - Sergio Cantero-Chinchilla
School of Electrical, Electronic and Mechanical Engineering, University of Bristol, Bristol BS8 1TR, UK
2 shared publications - Federico Martin de la Escalera
AERNNOVA Engineering Division SA, 3-28033 Madrid, Spain
1 shared publication - Francesco Ciampa
Department of Mechanical Engineering Sciences, University of Surrey, Guildford, UK
1 shared publication
Latest Publications
- Open Access
- 11 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (10) , 4319
Direct Calculation of the Group Velocity for Two-Dimensional Complex, Composite and Periodic Structures Using a Wave and Finite Element Scheme
Guided waves have immense potential for structural health monitoring applications in numerous industries including aerospace. It is necessary to evaluate guided wave dispersion characteristics, i.e., group velocity and phase velocity profiles, for using them effectively. For complex structures, the profiles can have highly irregular shapes. In this work, a direct method for calculating the group velocity profiles for complex, composite, and periodic structures using a wave and finite element scheme is presented. The group velocity calculation technique is easy to implement, highly computationally efficient, and works with the standard finite element formulation. The major contribution is summarised in the form of a comprehensive algorithm for calculating the group velocity profiles. The method is compared with the existing analytical and numerical methods for calculation of dispersion curves. Finally, an experimental study in a multilayered composite plate is conducted and the results are found to be in good agreement. The technique is suitable to be used in all guided wave application areas such as material characterisation, non-destructive testing, and structural health monitoring.
- 11 May 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (10) , 4319
Open AccessDirect Calculation of the Group Velocity for Two-Dimensional Complex, Composite and Periodic Structures Using a Wave and Finite Element Scheme
Guided waves have immense potential for structural health monitoring applications in numerous industries including aerospace. It is necessary to evaluate guided wave dispersion characteristics, i.e., group velocity and phase velocity profiles, for using them effectively. For complex structures, the profiles can have highly irregular shapes. In this work, a direct method for calculating the group velocity profiles for complex, composite, and periodic structures using a wave and finite element scheme is presented. The group velocity calculation technique is easy to implement, highly computationally efficient, and works with the standard finite element formulation. The major contribution is summarised in the form of a comprehensive algorithm for calculating the group velocity profiles. The method is compared with the existing analytical and numerical methods for calculation of dispersion curves. Finally, an experimental study in a multilayered composite plate is conducted and the results are found to be in good agreement. The technique is suitable to be used in all guided wave application areas such as material characterisation, non-destructive testing, and structural health monitoring.
- Open Access
Ultrasonic Guided Wave Testing on Cross-Ply Composite Laminate: An Empirical Study
Structural health monitoring comprises a set of techniques to detect defects appearing in structures. One of the most viable techniques is based on the guided ultrasonic wave test (UGWT), which consists of emitting waves throughout the structure, acquiring the emitted waves with various sensors, and processing the waves to detect changes in the structure. The UGWT of layered composite structures is challenging due to the anisotropic wave propagation characteristics of such structures and to the high signal attenuation that the waves experience. Hence, very low amplitude signals that are hard to distinguish from noise are typically recovered. This paper analyzes the propagation of guided waves along a cross-ply composite laminate following an empirical methodology. The research compares several implementations for UGWT with piezoelectric wafer active sensors. The reference for comparison is set on a basic mode, which considers the application of nominal voltage to a single sensor. The attenuation and spreading of the waves in several directions are compared when more energy is applied to the monitored structure. In addition, delayed multiple emission is also considered in multisensor tests. The goal of all the UGWT configurations is to transmit more energy to the structure such that the echoes of the emission are of greater amplitude and they ease the signal processing. The study is focused on the realization of viable monitoring systems for aeronautical composite made structures.
Open AccessUltrasonic Guided Wave Testing on Cross-Ply Composite Laminate: An Empirical Study
Structural health monitoring comprises a set of techniques to detect defects appearing in structures. One of the most viable techniques is based on the guided ultrasonic wave test (UGWT), which consists of emitting waves throughout the structure, acquiring the emitted waves with various sensors, and processing the waves to detect changes in the structure. The UGWT of layered composite structures is challenging due to the anisotropic wave propagation characteristics of such structures and to the high signal attenuation that the waves experience. Hence, very low amplitude signals that are hard to distinguish from noise are typically recovered. This paper analyzes the propagation of guided waves along a cross-ply composite laminate following an empirical methodology. The research compares several implementations for UGWT with piezoelectric wafer active sensors. The reference for comparison is set on a basic mode, which considers the application of nominal voltage to a single sensor. The attenuation and spreading of the waves in several directions are compared when more energy is applied to the monitored structure. In addition, delayed multiple emission is also considered in multisensor tests. The goal of all the UGWT configurations is to transmit more energy to the structure such that the echoes of the emission are of greater amplitude and they ease the signal processing. The study is focused on the realization of viable monitoring systems for aeronautical composite made structures.
- 1 August 2020
- Published by Elsevier in Composite Structures
- Vol. 246
Transient ultrasonic guided wave simulation in layered composite structures using a hybrid wave and finite element scheme
- 1 August 2020
- Published by Elsevier in Composite Structures
- Vol. 246
Transient ultrasonic guided wave simulation in layered composite structures using a hybrid wave and finite element scheme
- Open Access
An Empirical Study on Transmission Beamforming for Ultrasonic Guided-Wave Based Structural Health Monitoring
The development of reliable structural health monitoring techniques is enabling a healthy transition from preventive to condition-based maintenance, hence leading to safer and more efficient operation of different industries. Ultrasonic guided-wave based beamforming is one of the most promising techniques, which supports the monitoring of large thin-walled structures. However, beamforming has been typically applied to the post-processing stage (also known as virtual or receiver beamforming) because transmission or physical beamforming requires complex hardware configurations. This paper introduces an electronic structural health monitoring system that carries out transmission beamforming experiments by simultaneously emitting and receiving ultrasonic guided-waves using several transducers. An empirical characterization of the transmission beamforming technique for monitoring an aluminum plate is provided in this work. The high signal-to-noise ratio and accurate angular precision of the physical signal obtained in the experiments suggest that transmission beamforming can increase the reliability and robustnessof this monitoring technique for large structures and in real-world noisy environments.
Open AccessAn Empirical Study on Transmission Beamforming for Ultrasonic Guided-Wave Based Structural Health Monitoring
The development of reliable structural health monitoring techniques is enabling a healthy transition from preventive to condition-based maintenance, hence leading to safer and more efficient operation of different industries. Ultrasonic guided-wave based beamforming is one of the most promising techniques, which supports the monitoring of large thin-walled structures. However, beamforming has been typically applied to the post-processing stage (also known as virtual or receiver beamforming) because transmission or physical beamforming requires complex hardware configurations. This paper introduces an electronic structural health monitoring system that carries out transmission beamforming experiments by simultaneously emitting and receiving ultrasonic guided-waves using several transducers. An empirical characterization of the transmission beamforming technique for monitoring an aluminum plate is provided in this work. The high signal-to-noise ratio and accurate angular precision of the physical signal obtained in the experiments suggest that transmission beamforming can increase the reliability and robustnessof this monitoring technique for large structures and in real-world noisy environments.
- 15 November 2019
- Published by DEStech Publications
Ultrasonic Guided-Wave Based System Identification for Beams
Ultrasonic Guided-Wave Based System Identification for Beams
- 15 November 2019
- Published by DEStech Publications
Ultrasonic Guided-Wave Based System Identification for Beams
Ultrasonic Guided-Wave Based System Identification for Beams