Simon Vandelook
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Simon Vandelook has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Eveline Peeters
Vrije Universiteit Brussel
4 shared publications - Elise Elsacker
Vrije Universiteit Brussel
2 shared publications - Annah-Ololade Sangosanya
Vrije Universiteit Brussel
1 shared publication - Anouk Verstuyft
Research Group of Microbiology, Department of Bioengineering Sciences, Vrije Universiteit Brussel, Pleinlaan 2, 1050 Brussels, Belgium
1 shared publication - Aurélie Van Wylick
Research Group of Architectural Engineering Department of Architectural Engineering Vrije Universiteit Brussel Pleinlaan 2 Brussels B‐1050 Belgium
1 shared publication - Beatrice Benetti
, 2 Department of Biology , University of Padova , Via U. Bassi 58/B , Padova , Italy
1 shared publication
Latest Publications
- Open Access
Inoculum-to-interface distance tunes productivity in static liquid cultures of wood-decay fungi
Static liquid cultures of wood-decay fungi underpin applications in materials, food, and medicine, yet the mechanisms governing pellicle formation remain poorly understood, limiting rational optimisation at scale. We developed a time-lapse scanning and image analysis platform to visualise the process of pellicle formation across five white-rot fungal species, of which Trametes versicolor formed the thickest, heaviest pellicles and completed formation fastest. Kymographs revealed a reproducible four-stage sequence after inoculation and sedimentation of the biomass: recovery of viability, upward growth, pellicle initiation, and thickening. We formalised this as a model in which the time to pellicle establishment is determined by the distance between the settled biomass and the liquid–air interface. Increasing liquid depth relative to a fixed inoculum loading raised biomass and mat thickness, but prolonged formation. The results identify surface proximity as the dominant predictor of initiation timing. By fixing the inoculum at the liquid-air interface with a membrane, we validated that minimising the distance between the sedimented mycelium and the liquid surface accelerated and stabilised formation without compromising on pellicle biomass. By exposing the most relevant control variables, this work provides a quantitative basis for designing reliable liquid-state surface fermentations for emerging applications involving mycelium.
Open AccessInoculum-to-interface distance tunes productivity in static liquid cultures of wood-decay fungi
Static liquid cultures of wood-decay fungi underpin applications in materials, food, and medicine, yet the mechanisms governing pellicle formation remain poorly understood, limiting rational optimisation at scale. We developed a time-lapse scanning and image analysis platform to visualise the process of pellicle formation across five white-rot fungal species, of which Trametes versicolor formed the thickest, heaviest pellicles and completed formation fastest. Kymographs revealed a reproducible four-stage sequence after inoculation and sedimentation of the biomass: recovery of viability, upward growth, pellicle initiation, and thickening. We formalised this as a model in which the time to pellicle establishment is determined by the distance between the settled biomass and the liquid–air interface. Increasing liquid depth relative to a fixed inoculum loading raised biomass and mat thickness, but prolonged formation. The results identify surface proximity as the dominant predictor of initiation timing. By fixing the inoculum at the liquid-air interface with a membrane, we validated that minimising the distance between the sedimented mycelium and the liquid surface accelerated and stabilised formation without compromising on pellicle biomass. By exposing the most relevant control variables, this work provides a quantitative basis for designing reliable liquid-state surface fermentations for emerging applications involving mycelium.
- Open Access
- 1 January 2026
- Published by Walter de Gruyter GmbH in Environmental and Climate Technologies
- Vol. 30 (1) , 384-394
Bio-based Strategies to Enhance the Performance of Trametes versicolor Mycelium-Based Leather-Like Materials
Mycelium-based materials are emerging as promising bio-derived alternatives to animal and synthetic leather. However, their practical implementation is limited by insufficient mechanical strength and high surface hydrophilicity, which compromise dimensional stability and durability under humid conditions. This study investigates post-processing strategies aimed at enhancing structural integrity and improving surface hydrophobicity – an essential parameter to increase water resistance and extend service life – of Trametes versicolor mats produced through liquid-state surface fermentation (LSSF). A preliminary assessment showed that hot pressing increased the ultimate stress of glycerol-treated sheets from 0.31 ± 0.06 to 0.45 ± 0.06 MPa, confirming its suitability as a standard consolidation step. Subsequently, sorbitol- and citric acid-treated mats were coated with seven bio -based formulations, including proteins, polysaccharides, shellac, and wax–oil blends, and evaluated through static water contact angle (WCA) measurements. The uncoated mat exhibited the highest hydrophobicity (99.8 ± 15.0)°, while coated samples showed WCAs ranging from 65.1° (corn zein) to 95.3° (wax–oil balm). Coatings rich in hydrophobic long-chain molecules yielded the best water repellence, whereas protein- and polysaccharide-based films primarily altered surface texture without enhancing wettability. These results highlight the importance of formulation chemistry – particularly plasticizer content – in determining surface hydrophobicity, and provide a foundation for the development of scalable, fully bio-based surface finishing treatments for fungal leather-like materials.
- 1 January 2026
- Published by Walter de Gruyter GmbH in Environmental and Climate Technologies
- Vol. 30 (1) , 384-394
Open AccessBio-based Strategies to Enhance the Performance of Trametes versicolor Mycelium-Based Leather-Like Materials
Mycelium-based materials are emerging as promising bio-derived alternatives to animal and synthetic leather. However, their practical implementation is limited by insufficient mechanical strength and high surface hydrophilicity, which compromise dimensional stability and durability under humid conditions. This study investigates post-processing strategies aimed at enhancing structural integrity and improving surface hydrophobicity – an essential parameter to increase water resistance and extend service life – of Trametes versicolor mats produced through liquid-state surface fermentation (LSSF). A preliminary assessment showed that hot pressing increased the ultimate stress of glycerol-treated sheets from 0.31 ± 0.06 to 0.45 ± 0.06 MPa, confirming its suitability as a standard consolidation step. Subsequently, sorbitol- and citric acid-treated mats were coated with seven bio -based formulations, including proteins, polysaccharides, shellac, and wax–oil blends, and evaluated through static water contact angle (WCA) measurements. The uncoated mat exhibited the highest hydrophobicity (99.8 ± 15.0)°, while coated samples showed WCAs ranging from 65.1° (corn zein) to 95.3° (wax–oil balm). Coatings rich in hydrophobic long-chain molecules yielded the best water repellence, whereas protein- and polysaccharide-based films primarily altered surface texture without enhancing wettability. These results highlight the importance of formulation chemistry – particularly plasticizer content – in determining surface hydrophobicity, and provide a foundation for the development of scalable, fully bio-based surface finishing treatments for fungal leather-like materials.
- Top Cited Papers
- 1 July 2020
- Published by Elsevier in Science of The Total Environment
- Vol. 725, 138431
A comprehensive framework for the production of mycelium-based lignocellulosic composites
- 1 July 2020
- Published by Elsevier in Science of The Total Environment
- Vol. 725, 138431
Top Cited PapersA comprehensive framework for the production of mycelium-based lignocellulosic composites
- Top Cited PapersOpen Access
- 22 July 2019
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 14 (7) , e0213954
Mechanical, physical and chemical characterisation of mycelium-based composites with different types of lignocellulosic substrates
The current physical goods economy produces materials by extracting finite valuable resources without taking their end of the life and environmental impact into account. Mycelium-based materials offer an alternative fabrication paradigm, based on the growth of materials rather than on extraction. Agricultural residue fibres are inoculated with fungal mycelium, which form an interwoven three-dimensional filamentous network binding the feedstock into a lightweight material. The mycelium-based material is heat-killed after the growing process. In this paper, we investigate the production process, the mechanical, physical and chemical properties of mycelium-based composites made with different types of lignocellulosic reinforcement fibres combined with a white rot fungus, Trametes versicolor. This is the first study reporting the dry density, the Young’s modulus, the compressive stiffness, the stress-strain curves, the thermal conductivity, the water absorption rate and a FTIR analyse of mycelium-based composites by making use of a fully disclosed protocol with T. versicolor and five different type of fibres (hemp, flax, flax waste, softwood, straw) and fibre processings (loose, chopped, dust, pre-compressed and tow). The thermal conductivity and water absorption coefficient of the mycelium composites with flax, hemp, and straw have an overall good insulation behaviour in all the aspects compared to conventional materials such as rock wool, glass wool and extruded polystyrene. The conducted tests reveal that the mechanical performance of the mycelium-based composites depends more on the fibre processing (loose, chopped, pre-compressed, and tow), and size than on the chemical composition of the fibres. These experimental results show that mycelium-composites can fulfil the requirements of thermal insulation and have the potential to replace fosile-based composites. The methology used to evaluate the suitability and selection of organic waste-streams proved to be effective for the mycelium-material manufacturing applications.
- 22 July 2019
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 14 (7) , e0213954
Top Cited PapersOpen AccessMechanical, physical and chemical characterisation of mycelium-based composites with different types of lignocellulosic substrates
The current physical goods economy produces materials by extracting finite valuable resources without taking their end of the life and environmental impact into account. Mycelium-based materials offer an alternative fabrication paradigm, based on the growth of materials rather than on extraction. Agricultural residue fibres are inoculated with fungal mycelium, which form an interwoven three-dimensional filamentous network binding the feedstock into a lightweight material. The mycelium-based material is heat-killed after the growing process. In this paper, we investigate the production process, the mechanical, physical and chemical properties of mycelium-based composites made with different types of lignocellulosic reinforcement fibres combined with a white rot fungus, Trametes versicolor. This is the first study reporting the dry density, the Young’s modulus, the compressive stiffness, the stress-strain curves, the thermal conductivity, the water absorption rate and a FTIR analyse of mycelium-based composites by making use of a fully disclosed protocol with T. versicolor and five different type of fibres (hemp, flax, flax waste, softwood, straw) and fibre processings (loose, chopped, dust, pre-compressed and tow). The thermal conductivity and water absorption coefficient of the mycelium composites with flax, hemp, and straw have an overall good insulation behaviour in all the aspects compared to conventional materials such as rock wool, glass wool and extruded polystyrene. The conducted tests reveal that the mechanical performance of the mycelium-based composites depends more on the fibre processing (loose, chopped, pre-compressed, and tow), and size than on the chemical composition of the fibres. These experimental results show that mycelium-composites can fulfil the requirements of thermal insulation and have the potential to replace fosile-based composites. The methology used to evaluate the suitability and selection of organic waste-streams proved to be effective for the mycelium-material manufacturing applications.