Igor Aleksejev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Igor Aleksejev has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Artur Jutman
Tallinn University of Technology
12 shared publications - Sergei Devadze
Testonica Lab, Tallinn, Estonia
9 shared publications - Raimund Ubar
Tallinn University of Technology
7 shared publications Thomas Wenzel
GOEPEL electronic GmbH,Jena,Germany
3 shared publications- Jaan Raik
Department of Computer Systems, Tallinn University of Technology, Tallinn, Estonia
2 shared publications - Konstantin Shibin
Testonica Lab, Tallinn, Estonia
2 shared publications
Latest Publications
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Ways for board and system test to benefit from FPGA embedded instrumentation
With continually growing adoption of FPGA based designs, and more features and capabilities available in FPGAs, board and system level test applications can - and should - take advantage of FPGA embedded instrumentation. Such FPGA assisted tests not only improve manufacturing test but also allow extensive testing in the field to address issues such as no-fault-found syndrome by enabling the detection of environment-induced defects or latent defects (related to bad solder joint quality, aging, etc.). In this paper we are briefly reviewing different types of FPGA embedded instruments before specifically addressing synthetic instrumentation and focusing on example use cases. We will be discussing design for test considerations, quality of test and diagnostics, savings in test time and test cost, and levels of automation previously not associated with functional and performance / stress test development.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-10
Ways for board and system test to benefit from FPGA embedded instrumentation
With continually growing adoption of FPGA based designs, and more features and capabilities available in FPGAs, board and system level test applications can - and should - take advantage of FPGA embedded instrumentation. Such FPGA assisted tests not only improve manufacturing test but also allow extensive testing in the field to address issues such as no-fault-found syndrome by enabling the detection of environment-induced defects or latent defects (related to bad solder joint quality, aging, etc.). In this paper we are briefly reviewing different types of FPGA embedded instruments before specifically addressing synthetic instrumentation and focusing on example use cases. We will be discussing design for test considerations, quality of test and diagnostics, savings in test time and test cost, and levels of automation previously not associated with functional and performance / stress test development.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Embedded instrumentation toolbox for screening marginal defects and outliers for production
High-performance communication interfaces in modern complex electronic systems bring new challenges for board-level manufacturing test. Various means of calibration and error-correction that are incorporated into high-speed protocols tend to hide manufacturing flaws thus making comprehensive testing be an extremely hard task. Links transmitting at gigabit rates are especially susceptible to so-called marginal defects. Marginal defect often escape detection by commonly used test methods as they manifest themselves only under certain conditions that may sporadically occur during device operation in the field. As a result, undetected marginal defects badly affect system stability and reduce its overall operating margin. In this paper, we present a novel embedded instrumentation toolbox intended for use in volume production environments to screen out outliers and marginal devices. The paper focuses on instruments for testing marginal defects on High-Speed Serial Links and DDR3/4 interfaces.
- 1 September 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-9
Embedded instrumentation toolbox for screening marginal defects and outliers for production
High-performance communication interfaces in modern complex electronic systems bring new challenges for board-level manufacturing test. Various means of calibration and error-correction that are incorporated into high-speed protocols tend to hide manufacturing flaws thus making comprehensive testing be an extremely hard task. Links transmitting at gigabit rates are especially susceptible to so-called marginal defects. Marginal defect often escape detection by commonly used test methods as they manifest themselves only under certain conditions that may sporadically occur during device operation in the field. As a result, undetected marginal defects badly affect system stability and reduce its overall operating margin. In this paper, we present a novel embedded instrumentation toolbox intended for use in volume production environments to screen out outliers and marginal devices. The paper focuses on instruments for testing marginal defects on High-Speed Serial Links and DDR3/4 interfaces.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
On coverage of timing related faults at board level
In this paper, we demonstrate a clear gap in board level test coverage under category of timing related faults (TRFs). Although there are techniques that are capable to detect TRFs, there is no fault coverage metrics to quantify the quality of these techniques. To do that, we propose an easy-to-implement interconnect-level fault model extension towards TRFs. This extension can be integrated into existing test coverage models providing additional information on coverage of timing-related faults.
- 1 May 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-2
On coverage of timing related faults at board level
In this paper, we demonstrate a clear gap in board level test coverage under category of timing related faults (TRFs). Although there are techniques that are capable to detect TRFs, there is no fault coverage metrics to quantify the quality of these techniques. To do that, we propose an easy-to-implement interconnect-level fault model extension towards TRFs. This extension can be integrated into existing test coverage models providing additional information on coverage of timing-related faults.
- 28 April 2016
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 32 (3) , 245-255
Optimization of Boundary Scan Tests Using FPGA-Based Efficient Scan Architectures
- 28 April 2016
- Published by Springer Nature in Journal of Electronic Testing
- Vol. 32 (3) , 245-255
Optimization of Boundary Scan Tests Using FPGA-Based Efficient Scan Architectures
- 1 March 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Complex delay fault reasoning with sequential 7-valued algebra
A method is proposed for simulating of transition delay faults (TDF) at different fault propagation conditions. The main idea of the method is to extend the TDF model, traditionally considered as a class of robustly tested delay faults, to a class of TDFs with extended detection conditions like non-robust and functional sensitization. A new sensitization type, called nonrobust functional sensitization was introduced as well. A novel delay fault reasoning algorithm based on sequential 7-valued algebra is presented, which is used for fault coverage calculation separately for all mentioned four types of TDFs. By experimental results we established that the fault coverage share for different types of TDFs considerably depends on the quality of delay test.
- 1 March 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Complex delay fault reasoning with sequential 7-valued algebra
A method is proposed for simulating of transition delay faults (TDF) at different fault propagation conditions. The main idea of the method is to extend the TDF model, traditionally considered as a class of robustly tested delay faults, to a class of TDFs with extended detection conditions like non-robust and functional sensitization. A new sensitization type, called nonrobust functional sensitization was introduced as well. A novel delay fault reasoning algorithm based on sequential 7-valued algebra is presented, which is used for fault coverage calculation separately for all mentioned four types of TDFs. By experimental results we established that the fault coverage share for different types of TDFs considerably depends on the quality of delay test.
- 1 March 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23730862,p. 1-6
Virtual reconfigurable scan-chains on FPGAs for optimized board test
This paper presents a method for optimization of board-level scan-test with the help of reconfigurable scan-chains (RSCs) implemented in a programmable logic of FPGA. Despite that the RSC concept is a well-known solution for scan-based test time reduction, the usage of RSC may lead to un-acceptable hardware overhead. In our work, we are targeting a completely new approach of exploiting on-board FPGA resources that being unconfigured are typically available during the manufacturing test phase for carrying out tests using temporarily implemented virtual RSC structures. As the allocated FPGA logic is re-claimed for functional use after the test is finished, the presented method delivers all the advantages of RSCs at no extra HW cost. Experimental results show that the proposed virtual RSCs can fit into all available commercial FPGAs providing a significant overall test time reduction in comparison with traditional Boundary Scan approach.
- 1 March 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23730862,p. 1-6
Virtual reconfigurable scan-chains on FPGAs for optimized board test
This paper presents a method for optimization of board-level scan-test with the help of reconfigurable scan-chains (RSCs) implemented in a programmable logic of FPGA. Despite that the RSC concept is a well-known solution for scan-based test time reduction, the usage of RSC may lead to un-acceptable hardware overhead. In our work, we are targeting a completely new approach of exploiting on-board FPGA resources that being unconfigured are typically available during the manufacturing test phase for carrying out tests using temporarily implemented virtual RSC structures. As the allocated FPGA logic is re-claimed for functional use after the test is finished, the presented method delivers all the advantages of RSCs at no extra HW cost. Experimental results show that the proposed virtual RSCs can fit into all available commercial FPGAs providing a significant overall test time reduction in comparison with traditional Boundary Scan approach.
- 1 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10893539,p. 1-10
FPGA-based synthetic instrumentation for board test
This paper studies a new approach for board-level test based on synthesizable embedded instruments implemented on FPGA. This very recent methodology utilizes programmable logic devices (FPGA) that are usually available on modern PCBs to a large extent. The purpose of an embedded instrument is to carry out a vast portion of test application related procedures, perform measurement and configuration of system components thus minimizing the usage of external test equipment. By replacing traditional test and measurement equipment with embedded synthetic instruments it is possible not only to achieve the significant reduction of test costs but also facilitate high-speed and at-speed testing. We detail the motivation and classify the FPGA-based instrumentation into different categories based on the implementation and application domains. Experimental results show the efficiency of this approach.
- 1 November 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 10893539,p. 1-10
FPGA-based synthetic instrumentation for board test
This paper studies a new approach for board-level test based on synthesizable embedded instruments implemented on FPGA. This very recent methodology utilizes programmable logic devices (FPGA) that are usually available on modern PCBs to a large extent. The purpose of an embedded instrument is to carry out a vast portion of test application related procedures, perform measurement and configuration of system components thus minimizing the usage of external test equipment. By replacing traditional test and measurement equipment with embedded synthetic instruments it is possible not only to achieve the significant reduction of test costs but also facilitate high-speed and at-speed testing. We detail the motivation and classify the FPGA-based instrumentation into different categories based on the implementation and application domains. Experimental results show the efficiency of this approach.
- 1 May 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Embedded synthetic instruments for Board-Level testing
The main purpose of this paper is to refine the benefits of the FPGA-based synthetic instrumentation concept (see Section 1) proposed by us earlier [1] as well as to provide some new experimental data based on real industrial designs to show the efficiency of our methodology (see Section 2).
- 1 May 2012
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Embedded synthetic instruments for Board-Level testing
The main purpose of this paper is to refine the benefits of the FPGA-based synthetic instrumentation concept (see Section 1) proposed by us earlier [1] as well as to provide some new experimental data based on real industrial designs to show the efficiency of our methodology (see Section 2).
- 1 November 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Fast extended test access via JTAG and FPGAs
This paper describes a new test access protocol for system-level testing of printed circuit boards for manufacturing defects. We show that the protocol can be based on standard boundary scan (BS) instructions and test access mechanism (TAM). It means that the methodology does not require any changes/redesign of hardware and can be immediately implemented in the electronic manufacturing. Our solution needs however a proper software support and availability of programmable devices (FPGAs, CPLDs, etc.) on the board under test. The new technique dramatically extends the applicability of BS testing in the reality of modern complex on-board data transfer buses and protocols. Potentially, it can also increase the speed of in-system programming of flash memories and other tasks that are traditionally performed using BS.
- 1 November 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Fast extended test access via JTAG and FPGAs
This paper describes a new test access protocol for system-level testing of printed circuit boards for manufacturing defects. We show that the protocol can be based on standard boundary scan (BS) instructions and test access mechanism (TAM). It means that the methodology does not require any changes/redesign of hardware and can be immediately implemented in the electronic manufacturing. Our solution needs however a proper software support and availability of programmable devices (FPGAs, CPLDs, etc.) on the board under test. The new technique dramatically extends the applicability of BS testing in the reality of modern complex on-board data transfer buses and protocols. Potentially, it can also increase the speed of in-system programming of flash memories and other tasks that are traditionally performed using BS.
- 1 March 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23730862,p. 1-6
Turning JTAG inside out for fast extended test access
This paper describes a new test access protocol for system-level testing of printed circuit boards for manufacturing defects. We show that the protocol can be based on standard Boundary Scan (BS) instructions and test access mechanism (TAM). It means that the methodology does not require any changes/redesign of hardware and can be immediately implemented in the electronic manufacturing. Our solution needs however a proper software support and availability of programmable devices (FPGAs, CPLDs, etc.) on the board under test. The new technique dramatically extends the applicability of BS testing in the reality of modern complex on-board data transfer buses and protocols. Potentially, it can also increase the speed of in-system programming of flash memories and other tasks that are traditionally performed using BS.
- 1 March 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 23730862,p. 1-6
Turning JTAG inside out for fast extended test access
This paper describes a new test access protocol for system-level testing of printed circuit boards for manufacturing defects. We show that the protocol can be based on standard Boundary Scan (BS) instructions and test access mechanism (TAM). It means that the methodology does not require any changes/redesign of hardware and can be immediately implemented in the electronic manufacturing. Our solution needs however a proper software support and availability of programmable devices (FPGAs, CPLDs, etc.) on the board under test. The new technique dramatically extends the applicability of BS testing in the reality of modern complex on-board data transfer buses and protocols. Potentially, it can also increase the speed of in-system programming of flash memories and other tasks that are traditionally performed using BS.