TFThomas Feldhausen

Thomas Feldhausen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Thomas Feldhausen has a total of 186 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Vision-derived stability indicators from melt pool and wire dynamics in laser hot-wire directed energy deposition

    by Mario Rodriguez-Parra, Miguel Hoffmann, Mithulan Paramanathan, Thomas Feldhausen, Eric MacDonald

    Laser hot-wire directed energy deposition (LHW-DED) improves process performance by enhancing wire preheating. Reliable in situ assessment of process stability remains challenging because the melt-pool behavior and wire transfer are commonly evaluated separately. This study develops vision-derived stability indicators by jointly characterizing melt-pool geometry and wire dynamics during the deposition of stainless steel 316LSi under varying laser power and hot-wire power. Optical videos were analyzed using multi-Otsu segmentation for melt-pool area extraction and the Segment Anything Model 2 for temporal wire segmentation. Melt-pool area was used to characterize the energy input, while frame-to-frame Intersection over Union (IoU), IoU volatility, and angle variability were evaluated as indicators of wire stability. Low energy conditions produced smaller melt pools and greater wire flutter, whereas sufficient energy inputs produced larger melt pools and more consistent wire behavior. Parameter-level correlations showed that melt-pool area for single beads was related to penetration depth and total cross-sectional area measured by optical microscopy. Melt-pool area was also associated with wire stability during the single-bead laser-power sweep. These results establish melt-pool geometry and wire dynamics as complementary indicators of LHW-DED stability and support future process qualification and in situ feedback control.

  • Open Access

    Cross domain additive manufacturing video object segmentation dataset

    by Calvin Wetzel, Hector Santos-Villalobos, James Haley, Vladimir Orlyanchik, Mario Rodriguez Parra, Mithulan Paramanathan, Tom Feldhausen, Michael Sebok, Chris Masuo, Vincent Paquit

  • Reduction of baseplate distortion during directed energy deposition using compliant features

    by Ritin Mathews, Justin West, Mithulan Paramanathan, Christopher Tyler, Scott Smith, Thomas Feldhausen

  • Open Access

    Reduction of baseplate distortion during directed energy deposition using compliant features

    by Ritin Mathews, Justin West, Mithulan Paramanathan, Christopher Tyler, Scott Smith, Thomas Feldhausen

    Distortion in additive manufacturing (AM) remains a barrier to its adoption in precision industries. Baseplate warpage is one such issue which compromises the feasibility of post-process precision machining. The restriction to thermal contraction of the deposited part, imposed by the baseplate, generates bending moments that, in turn, causes warpage. A novel distortion mitigation strategy using baseplates with integrated compliant features, which enables thermal contraction of the build is presented. Six unique design concepts, including a solid reference, are evaluated using two deposition geometries. A laser, hot-wire, directed energy deposition (DED) process is used to deposit a symmetric cylindrical part (C-part) and a T-shaped asymmetric part (T-part). Flatness deviation of baseplates is measured using structured light 3D scanning. Measurements reveal a reduction in net flatness deviation of 58.8% for the C-part and 40.9% for the T-part, compared to the solid reference. While most designs yielded reductions exceeding 30% and 20% for the C- and T-parts, respectively, one configuration resulted in increased deviation. Finite element (FE) simulations are performed to elucidate the underlying mechanisms affecting distortion of compliant baseplates during DED. Despite variations between predictions and measurements, the general trends agree. It also revealed that initial flatness errors in baseplates significantly affect its deviation during deposition. Predictions indicate that compliant features significantly affect the thermal distribution as well as the evolution of flatness deviation in the baseplate during deposition. Notably, one design exhibited a reduction in distortion during cooling, following its initial increase during deposition. FE predictions show a maximum reduction of 60.9% and 38.8% in net flatness deviation for the C- and T-parts, respectively. The performance of compliant baseplates is found to be governed by both its the thermal and mechanical characteristics, which are crucial factors to be considered during design. Finally, the residual strain at the build-baseplate interface has been significantly reduced in the presence of complaint features.

  • Open Access

    Upcycling Red Mud as a Flux for Direct Reduced Iron Refinement and its Comparison with Commercial Flux

    by Vanshika Singh, Rangasayee Kannan, Brian Hicks, Chris M. Fancher, Sarah Graham, Brett Spigarelli, Julio Ortega Rojas, Samuel Bell, Peeyush Nandwana, Sudarsanam Suresh Babu, et al.

    Red mud is a by-product of aluminum extraction process and has a composition similar to the flux used for iron extraction. This makes red mud a promising cost-effective and sustainable flux for steelmaking. Direct Reduced Iron (DRI) which is typically refined using ionic conductive fluxes for steel production poses a potential avenue for red mud re-utilization. In this study, we investigated red mud as fluxing agent for the refinement of DRI experimentally in corroboration with thermodynamic model and compared the outcomes with that produced via conventional commercial flux. Results indicated that high purity iron can be obtained by using red mud as a flux and has a higher compression strength compared to iron obtained using commercial flux. Thermo-kinetic calculations were used to rationalize the efficacy of red mud as a flux for DRI refinement.

  • Open Access

    Multi-Material Deposition Strategy for Hybrid Additive-Subtractive Manufacturing of Tooling Mold

    by Miguel Hoffmann, Mithulan Paramanathan, Lauren Heinrich, Rangasayee Kannan, Kenton B. Fillingim, Peeyush Nandwana, Thomas Feldhausen, Yousub Lee

    This paper presents a hybrid additive-subtractive manufacturing strategy for producing multi-material tooling molds. A functional Frisbee mold was fabricated using tri-metallic (316L, 17-4PH, H13) and bi-metallic (17-4PH, H13) designs. The process involved interleaved laser hot-wire directed energy deposition and integrated machining to enhance interface quality and dimensional precision while minimizing the use of costly, hard-to-machine materials. Comprehensive characterization, including X-ray computed tomography, optical microscopy, and Vickers microhardness testing, confirmed high part densities (≥99.5%), well-defined material transitions, and excellenthardness (212 HV for 316L, 347 HV for 17-4PH, and 599 HV for H13). The tri-metallic approach reduced material costs by 53% and significantly shortened machining time compared to a full-H13 mold. These findings highlight the potential of hybrid multi-material manufacturing for tooling applications, offering a scalable, cost-effective alternative to traditional methods.

  • Open Access

    Future foundries: A convergent manufacturing platform

    by Shramana Ghosh, Miguel Hoffmann, Lauren Heinrich, Kenton B. Fillingim, Joshua Vaughan, Brian K. Post, Thomas Feldhausen


  • Open Access

    Simulation driven adaptive sampling for neutron-diffraction based strain mapping of additively manufactured parts *

    by Venkatakrishnan S V, Ke An, Yousub Lee, Thomas Feldhausen, Lauren Heinrich, Stephen DeWitt

    Neutron diffraction based strain mapping is a useful technique for measuring residual strains in additively manufactured (AM) metal parts. The measurement is traditionally done by scanning the sample in a point-wise raster pattern to extract the strain at each position. Since the overall scan can span several hours, adaptive sampling approaches using Bayesian optimization based on Gaussian process (BO-GP) regression have been introduced—demonstrating that even with a fraction of the typically made measurements the dominant strain patterns in the sample can be reconstructed. However, the parameters of the BO-GP algorithm have to be carefully chosen for best performance, and the movement time between arbitrary points can offset the time savings from a reduced number of measurement locations. In this paper, we propose algorithms to refine the BO-GP based methods by using simulations of strain patterns in AM parts based on the materials and the process used to print them. We demonstrate that the simulated strain patterns can be used to help choose better parameters for the BO-GP based framework—leading to low reconstruction error for the final strain pattern. Furthermore, we show that the strain mapping experiment can be initialized with a sampling pattern learnt from the simulation data and ordered to reduce movement time, dramatically enabling reduction in the overall time required to run the baseline BO-GP method.


  • Open Access

    Operational resilience of additively manufactured parts to stealthy cyberphysical attacks using geometric and process digital twins

    by Jeremy Cleeman, Adrian Jackson, Anandkumar Patel, Zihan Wang, Thomas Feldhausen, Chenhui Shao, Hongyi Xu, Rajiv Malhotra